Page 2
VETRON | Typical GmbH inadmissible and punishable. VETRON | Typical GmbH is only liable for damage caused by intent or gross negligence on the part of the manufacturer. Otherwise, liability is excluded.
Page 3
04. INTENDED USE / DECLARATION OF CONFORMITY 05. TECHNICAL DATA 06. TRANSPORT - PACKAGING - DISPOSAL - STORAGE | FIRST COMMISSIONING / DECOMMISSIONING 11 02. MACHINE DESCRIPTION 01. FRONT VIEW 02. BACK VIEW 03. BATTERY PROTECTION SYSTEM 04. POWER DISPLAY 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
Page 4
01. INSERT / REMOVE BATTERY PACK 02. TURN MACHINE ON / OFF 03. MATERIAL 04. ADJUST THE FINGER GUARD 19 04. MAINTENANCE 01. REPLACE THE KNIFE 02. SHARPEN THE KNIFE 03. LUBRICATE THE KNIFE 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
Page 5
» Do not operate cutters with damaged power cables or battery packs. » Do not keep the power cord under tension to prevent me- chanical damage. » Do not use the power cable or battery pack for other equip- ment. 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
Page 6
RISK OF BURNS! This symbol indicates that there is an increased risk of burning here. MAGNET! This symbol indicates that there is a magnet field. INFORMATION! This symbol displays information. ADVICE! This symbol indicates important information. 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
Danger of crushing. The tool, especially the battery pack is heavy and may cause injury when falling. Always mainain a frim grip and do not position the tool on the edge of any surface to prevent it from being knocked over. 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
Damage due to non-intended use is not covered by the manufacturer‘s liability! CE-CONFORMITY DECLARATION This piece of equipment complies with the applicable European regulations of relevant basic health and safety requirements, which are specified in the declaration of conformity and manufacturer. 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
01. Engage the lock switch. 02. Remove the battery. 03. Disconnect the charger from the power supply. 04. Clean the tool if necessary. 05. Store safely in accordance with the provisions in this manual and workplace safety regulations. 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
Wait for the battery to cool down, then start the machine again. » When the battery voltage drops. › This means the battery power is running low. If the battery has been recently charged, have it checked. Otherwise charge it. 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
POWER LEVEL INDICATION LED status Remaining Power 100% - 75% 75% - 50% 50% - 25% 25% - 0% NOTE! Depending on ambient temperature and battery condition, the accuracy of this indication may vary. 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
04. Make sure the battery sits firmly in the slot. REMOVING THE BATTERY 01. Press and hold down the clip buttons on the sides of the battery. 02. Pull the battery from the slot. 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
Page 16
To start the machine: 01. Disengage the lock switch by oushing it towards the battery pack. 02. Push the power button to start the tool. NOTE! Re-engage the lock switch when you stop operating the machine. 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
Page 17
03. Firmly push the knife along where you want to cut the material. Do not apply too much pressure. If the knife does not cut the material properly, try tighten it in front of the knife. 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
Page 18
finger guard. Positioning screw Finger guard 01. Loosen positioning screw. 02. Use the latch on the top end of the finger guard to adjsut the position. 03. Re-tighten the screw to set the new position. 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
04. Remove the knife cap and knife. 05. Place the new knife with it‘s flat, labeled surface facing the tool. 06. Insert the locking pin. 07. Put the knife cap back in place and tighten it to secure the knife. 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
Page 20
03. Hold the sharpener in this position for a few seconds, then release it. 04. Let the knife cool down. 05. Test if the knife is sharp enough. If not, repeat these steps as often as necessary. 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
Page 21
04. MAINTENANCE 03. LUBRICATE THE KNIFE 01. Screw open the oil nozzle 02. Refill the oil. 03. Close the oil nozzle by screwing the cap back on again. 05/2020 TYPICAL RK70 CORDLESS ROUND KNIFE...
Page 22
This machine may only be operated by adequately trained operators only after having completely read and understood the instruction manual. Parts are subject to changes in design without prior notice. VETRON TYPICAL EUROPE GmbH Clara-Immerwahr-Str. 6 67661 Kaiserslautern, Germany Tel.: +49 6301 320 75-0 Fax: +49 6301 320 75-11 info@vetrontypical.com...