Matco Tools SBJE1 Quick Start Manual

WARNING
Study, understand and follow all instructions provided with
this product. Read these instructions carefully before
installing, operating, servicing or repairing this tool. Keep
these instructions in a safe, accessible place.
INTENDED USE OF THE TOOL
This item is for removing Subaru lower ball joints and
other M12x125 stud 1.75" OD ball joints. Do not use
this tool outside of the designed intent. Never modify
the tool for any other purpose or use.
WARNING
Caution: To help prevent personal injury
• Normal use of this product is likely to expose the user
to dust and/or microscopic particles containing chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm.
www.P65Warnings.ca.gov
equipment and clothing when using this product. Study,
understand and follow all instructions provided with this
product. Failure to read and follow all warnings and
operating instructions may result in damages and serious
injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and Bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with accessories
not designed for it could result in serious injury or death.
• Always select the correct accessories of the correct size
and design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is
in secure position, and will not move during repair.
SUBARU BALL
JOINT EXTRACTOR
MODEL:
SBJE1
Always wear appropriate safety
.
Made in China
to Matco specifications
Product Type:
SUBARU BALL JOINT EXTRACTOR
1 YEAR LIMITED WARRANTY
The manufacturer warrants this product to the original user against
defective material or workmanship for a period of 1 year from the date of
purchase.
The manufacturer reserves the right to determine whether the part or
parts failed because of defective material, workmanship or other causes.
Failures caused by accident, alteration, or misuse are not covered by this
warranty.
The manufacturer, at its discretion, will repair or replace products covered
under this warranty free of charge. Repairs or replacements of products
covered under this warranty are warrantied for the remainder of the
original warranty period.
The manufacturer or its authorized service representatives must perform
all warranty repairs. Any repair to the product by unauthorized service
representatives voids this warranty. The rights under this warranty are
limited to the original user and may not be transferred to subsequent
owners.
This warranty is in lieu of all other warranties, expressed or implied,
including warranties of merchantability and fitness for a particular purpose.
Some states do not allow the exclusion or limitations of incidental or
consequential damages, so the above limitations may not apply to you.
Read these instructions carefully before installing, operating, servicing or
repairing this tool. Keep these instructions in a safe, accessible place.
INSTRUCTIONS:
• Using with an impact wrench:
1) Thread double sided round nut onto ball joint stud.
2) Back off the 24mm nut on tool to allow for the drive bolt
to slide forward.
3) Thread the drive bolt inside of the cup sleeve onto the
double sided adapter by rotating the entire tool until it
stops and the ball joint stud begins to turn.
4) Grease exposed threads.
5) Thread the 24mm nut down until it meets the washer.
6) Use a deep 24mm socket and ratchet or 24mm impact
socket and impact wrench to tighten the nut, pulling the
ball joint out.
6) Back the 24mm nut off the drive bolt to slide the
assembly forward and expose the removed ball joint for
disposal.
• Using with a slide hammer:
1) Position the vehicle securely on a lift and raise vehicle.
2) Thread double sided round nut onto ball joint stud.
3) Thread your 5/8-18 threaded slide hammer onto the
double nut.
4) Work the slide hammer to pull out the ball joint.
5) Un-thread the double sided round nut and dispose of
ball joint.
PRODUCT INFORMATION:
• Easy removal. For rusted and difficult to remove "bolt-in"
style Subaru ball joints.
• Time saving. Get the job done quicker using a 24mm
wrench, impact wrench or most slide hammers to
quickly remove lower ball joints.
• Comprehensive coverage. For Baja 2003+, Forester 1998+,
Impreza 1993+, Legacy 1990+, Outback 2000+ and more.
DO NOT DISCARD – GIVE TO USER
Page 1
Important
1808223-14