LEGRAND 682083 Quick Start Manual

Emergency Lighting Test Switch
682083 (Trade)
Emergency Lighting Test Switch
682083 (Trade)
204565 (27.07.2009)
204565 (16.09.2010)
204565 (27.07.2009)
Cat No 682083
Cat No 682083
Emergency Lighting Test Switch - Trade
Emergency Lighting
Cat No 682083
Six Month Test - 90 min
Test Switch - Trade
Emergency Lighting
Turn the Key-switch to Start Test position to start discharge test.
Test Switch - Trade
The Red button LED will flash once a second. OPERATION
During this test the contactor will operate for a period of 90 minutes + 45
OPERATION
minutes. The extra 45 minutes is designed to allow walk through to check the Six Month Test - 90 min
fittings. The total duration of this test is 135 minutes (90min+45min)
Six Month Test - 90 min
Operate the Key Switch and remove the key.
Push the Red button (STOP) to terminate the test
The Red pilot LED will flash at once a second.
Operate the Key Switch and remove the key.
Commissioning Test - 120min
During this test the contactor will engage for a period of 90
The Red pilot LED will flash at once a second.
Hold down the Red button (STOP) and turn Key-switch to Start Test position minutes + 45 minutes. The extra 45 minutes is designed to al-
During this test the contactor will engage for a period of 90
to start discharge test.
low walk through to check the fittings. The total duration of this
minutes + 45 minutes. The extra 45 minutes is designed to al-
The Red button LED will flash once every 0.5 seconds.
test is 135 minutes (90min+45min)
low walk through to check the fittings. The total duration of this
During this test the contactor will operate for a period of 120 minutes + 45
test is 135 minutes (90min+45min) Push the STOP button to terminate the test.
minutes. The extra 45 minutes is designed to allow walk through to check the
fittings. The total duration of this test is 165 minutes (120min+45min)
Push the STOP button to terminate the test.
Commissioning Test - 120min
Push the Red button (STOP) to terminate the test
Commissioning Test - 120min
Hold down the STOP button whilst operating the Key Switch.
Power up Time Delay
The Red pilot LED will flash once every 2 seconds.
Power-up time delay provides additional 10 minutes of emergency lighting Hold down the STOP button whilst operating the Key Switch.
During this test the contactor will engage for a period of 120
once the Mains power is restored. This is typically used to allow discharge
The Red pilot LED will flash once every 2 seconds.
minutes + 45 minutes. The extra 45 minutes is designed to al-
lamps to warm up and regain sufficient light before the emergency lights
During this test the contactor will engage for a period of 120
low walk through to check the fittings. The total duration of this
are turned off avoiding a black out period.
minutes + 45 minutes. The extra 45 minutes is designed to al-
test is 165 minutes (120min+45min)
Power-up time delay = 0 min
low walk through to check the fittings. The total duration of this
Power-up time delay = 10 min
Push the STOP button to terminate the test. test is 165 minutes (120min+45min)
To change Power-up time delay, turn Key-switch to Stand-by position and
Push the STOP button to terminate the test.
press down Red button for 5 seconds.
(Key on Stand-by position).
(Key on Stand-by position).
Red button LED solid On (Default)
Red button LED flashes every 3 seconds
Cat No 682083
Emergency Lighting
Cat No 682083
Test Switch - Trade
Emergency Lighting
Test Switch - Trade
WIRING DIAGRAM
WIRING DIAGRAM
When the optional 8 Channel Sensing
Module Cat No 682085 is required, the link
When the optional 8 Channel Sensing
between '+' and 'OP' must be removed.
Module Cat No 682085 is required, the link
(See wiring Diagram of Sensing Module)
between '+' and 'OP' must be removed.
(See wiring Diagram of Sensing Module)