Related Manuals for Sercomm IP3442M
Summary of Contents for Sercomm IP3442M
- Page 1 IP3442M WiFi Router Quick Start Guide P/N: 957DFR00E5 Document Version: 1.0 Copyright 2020. All Rights Reserved. All trademarks and trade names are the properties of their respective owners...
- Page 2 Package Contents The following items are included in the box: 1. IP3442M 2. Quick Start Guide 3. Power adapter 4. Wifi credential card If any of these items are damaged or missing, please contact your service provider immediately.
- Page 3 This chapter provides details of the IP3442M's features and capabilities Overview The IP3442M is designed to enhance the connectivity between your WiFi router and wireless client device while increasing the coverage of your existing WiFi network. With its simple setup, this high-speed 802.11ac extender works seamlessly with most routers.
- Page 4 Chapter 2 Basic Setup This chapter provides details on how to setup the IP3442M Front Panel Figure 1: Front Panel Red On, Green off – No internet. 1. Power/WAN (Green/Red) Blink Red,Green off - The Power LED will blink(Red) during boot up Green On, Red off-Internet connection is available.
- Page 5 LED is Green. Reset to manufacturer default values and reboot. When pressed and held over 7 seconds, the settings of the IP3442M will be set to their default values. Reboot. When pressed and held over 2 seconds and less than 5 seconds, the IP3442M will reboot.
- Page 6 Side Panel Figure 3: Back Panel WPS Button Push the WPS button on the device and on your other WiFi device to perform WPS function that easily creates an encryption-secured WiFi connection automatically.
- Page 7 Setup the IP3442M You can set up your IP3442M using web browser. Setup Using Web Browser Step 1: Make sure the WiFi router is on and working properly. Step 2: Connect the Router WAN port with your cable modem or PON device with an Ethernet cable.
- Page 8 Chapter 3 Safety This chapter provides you some safety operation warnings 1. Use the power supply adapter provided in the package only. Using any other adapters may cause damage to the equipment or result in operation failures. 2. The electrical load capacity of the socket and cables should meet the device’s requirement.
- Page 9 Appendix A Regulatory FCC Statement This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Need help?
Do you have a question about the IP3442M and is the answer not in the manual?
Questions and answers
How do I block someone from using my wifi?
To block a user from accessing your Sercomm IP3442M WiFi, follow these steps:
1. Connect your PC to the router using an Ethernet cable.
2. Open a web browser and enter http://192.168.1.1 in the address bar.
3. Log in using the username "admin" and the WPS PIN as the password (found via QR code on your WiFi credential card).
4. Go to the Wireless page and click on Basic Setup.
5. Change your WiFi name (SSID) and password to prevent unauthorized access.
6. Save the settings and restart the router if necessary.
This will disconnect all connected devices, and only users with the new password can reconnect.
This answer is automatically generated
My Ring cameras requires IPV4 and this router only supports IPV6. Is there a workaround or settings that can be changed?
how do i block a device from connecting?
is there a way to do port forwarding on this router website?
how to change password on ip3442m-L/us
To change the password on the Sercomm IP3442M:
1. Ensure the WiFi router is on and working.
2. Connect your PC to the router using an Ethernet cable.
3. Open a web browser and go to http://192.168.1.1.
4. Enter the username (admin) and the password (WPS PIN from the WiFi credential card).
5. Navigate to the Wireless page.
6. Click Basic Setup and update your WiFi name and password.
This answer is automatically generated