Table of Contents
Advertisement
Quick Links
Singxer SDA-6 User Handbook
广州声仕电子有限公司
Guangzhou Singxer Electronic Co., Ltd.
地址：中国广东省广州市番禺区新造镇
Address: Xinzao Town Panyu District Guangzhou City Guangdong province, China
电话：180-7881-2020
Phone number: 86 180-7881-2020
联系人：陈先生
Contacts：Mr.chen
E-mail: leter@singxer.com
E-mail: leter15@foxmail.com
Skype: leter@singxer.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Singxer SDA-6
Summary of Contents for Singxer SDA-6
- Page 1 Singxer SDA-6 User Handbook 广州声仕电子有限公司 Guangzhou Singxer Electronic Co., Ltd. 地址：中国广东省广州市番禺区新造镇 Address: Xinzao Town Panyu District Guangzhou City Guangdong province, China 电话：180-7881-2020 Phone number: 86 180-7881-2020 联系人：陈先生 Contacts：Mr.chen E-mail: leter@singxer.com E-mail: leter15@foxmail.com Skype: leter@singxer.com...
- Page 2 3. Connect the SDA-6 to a computer or digital player via USB Type A to Type B cable. (Note: USB’s 5V power supply can not be open circuited); For WINDOWS system, it requires the SDA-6 driver to be installed, although the SDA-6 can be used without driver under the latest version of WINDOWS 10, it is recommended to use the driver we provided;...
- Page 3 Standby button, OLED will display MUTE in mute mode. Hold and press it for 2 seconds will switch the SDA-6 to standby mode. OLED screen will be off and the standby LED on the left side of OLED screen will light up, you can press any button to exit standby mode.
- Page 4 11. 采样率显示：PCM 为 44.1K-768K，DSD 为 2.82M- 24.57M，分别对应 DSD64-DSD512。 12. 四个按键是 Standby,CLK,D-filter,INPUT. 单击 Standby 按键是控制输出静音，OLED 显示 MUTE；长按 2 秒是进入待机状态，OLED 屏关闭，OLED 屏左边的 LED 待机灯亮起， 按下任意键退出待机。待机状态下，只是关闭了输出，但是内部电路是正常工作的。 13. 遥控器的功能和上述按键旋钮的功能是对应的， MUTE 是静音，POWER 标注代表待机， 上面白色的是 LED 指示灯。PLL，Bri,INV，V+,V-，PRE 六个键功能为备用键，在 SDA-6 上面无作用。 SDA-6 HDMI-I2S jumper setting table PS Audio HOLO...
Need help?
Do you have a question about the SDA-6 and is the answer not in the manual?
Questions and answers
jak nakonfigurovat i2s
To configure I2S for the Singxer SDA-6, follow these steps:
1. Select I2S Input: Use the INPUT button to cycle through input sources until I2S is selected.
2. Set DIP Switches: Configure the DIP switches on the bottom of the device to match the correct pin configuration for your I2S source. Different manufacturers may have different wiring, so refer to the jumper setting table in the manual.
3. Check Compatibility: Ensure your I2S signal is correctly formatted, as the SDA-6 uses a direct pass-through mode for I2S and does not support PLL or external clock adjustments.
4. Verify DSD Settings: If using DSD, ensure the DSD_ON pin (PIN13) is correctly set according to your source requirements.
5. Confirm Operation: Once settings are configured, check the OLED display for the correct sample rate and format.
This ensures proper I2S functionality with the SDA-6.
This answer is automatically generated