Related Manuals for Minnich A-1CL
Summary of Contents for Minnich A-1CL
-
Page 1: Chapter 1-Introduction
Minnich DUST COLLECTOR OPERATOR/SERVICE MANUAL Minnich Manufacturing Contact 1444 ST RT 42 Phone: (419)-903-0010 Mansfield,OH 44903 Email: sales@minnich-mfg.com... -
Page 2: Table Of Contents
Chapter 2-................................17 Parts Manual............................17 Notes...............................29 Warranty..............................30 Parts Ordering Online..........................31 It is Minnich’s policy to constantly strive to See engine manual for information pertaining improve our products. The information, spec- to the engine. ifications, and illustrations in this publication are based on the information in effect at the same time as approval for printing and pub- lishing. -
Page 3: General Warnings
GENERAL WARNINGS CALIFORNIA PROPOSITION 65 Engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the Sate of California to cause cancer, birth defects and other reproductive harm. -
Page 4: General Safety
GENERAL SAFETY Do not operate or service the equipment before SAFETY SYMBOLS reading the entire manual. Safety precautions Potential hazards associated with the operation should be followed at all times when operating this of this equipment will be referenced with hazards equipment. - Page 5 ∆ Never use accessories or attachments that are ∆ NEVER operate this equipment without not recommended by Minnich for the equip- proper protective clothing, shatter proof ment. Damage to the equipment and/or injury glasses, respirator protection, hearing pro- to user may result.
- Page 6 GENERAL SAFETY ENVIRONMENTAL SAFETY ∆ DO NOT expose vibrator to rain. ∆ DO NOT use vibrator motor in damp or wet ∆ DO NOT pour waste or oil directly into the locations without proper electrical circuits. ground, down a drain or into any water ∆...
- Page 7 NOISE MAY ∆ Make sure the lubricator is filled with proper DAMAGE HEARING WEAR PROPER HEARING lubricant. See Minnich recommended lubricant PROTECTION FLYING PARTICLES MAY CAUSE below. EYE INJURIES WEAR PROPER EYE ERSTAND OWNERS MANUAL COMPLETELY.
- Page 8 To find the latest revision of this publication, visit our website at: www.minnich-mfg.com The force exerted by an internal concrete vibra- tor is controlled by the weight and the speed at which the eccentric rotates.
- Page 9 GENERAL SAFETY TOOL USE AND CARE SERVICE 1. Only qualified persons should operate the 1. DO NOT run the drill unit while you make machine. Make sure you operate and service adjustments and repairs unless the procedure your machine according to the instructions list- is approved.
-
Page 10: General Specification
GENERAL SPECIFICATION SINGLE CAN DUST SINGLE CAN ON-GRADE Dust Collector Manual... - Page 11 GENERAL SPECIFICATION DOUBLE CAN DUST TRIPLE CAN DUST Dust Collector Manual...
-
Page 12: Safety Decal Location
SAFETY DECAL LOCATION All safety labels on Minnich Manufacturing units have been carefully placed so they can be eas- ily seen at all times. There are several different types of labels on the units. Always keep these warnings free of dirt, concrete, or anything else that restricts visibility. Never remove the labels for any reason. - Page 13 SAFETY DECAL LOCATION All safety labels on Minnich Manufacturing units have been carefully placed so they can be eas- ily seen at all times. There are several different types of labels on the units. Always keep these warnings free of dirt, concrete, or anything else that restricts visibility. Never remove the labels for any reason.
- Page 14 SAFETY DECAL LOCATION All safety labels on Minnich Manufacturing units have been carefully placed so they can be eas- ily seen at all times. There are several different types of labels on the units. Always keep these warnings free of dirt, concrete, or anything else that restricts visibility. Never remove the labels for any reason.
-
Page 15: Set-Up/Instillation
2009 have mounting tabs welded to the rear of the drill frame to accept the dust collector. b. Minnich models A-1CL, A-1C and A-2C ADJUSTMENTS require a piece of angle iron with two mount 1. With the drill bed in the lowered drilling position,... -
Page 16: Operation/Maintenance
When the drill turns on, the appropriate ∆ Minnich equipment does NOT contain fire or explo- dust collection canister will automatically turn on and run sive prevention equipment. A prudent user of dust... -
Page 17: Chapter 2
PARTS MANUAL Dust Collector Manual... - Page 18 GENERAL SAFETY Dust Collector Manual...
- Page 19 PARTS MANUAL Dust Collector Manual...
- Page 20 PARTS MANUAL Dust Collector Manual...
- Page 21 PARTS MANUAL Dust Collector Manual...
- Page 22 GENERAL SAFETY Dust Collector Manual...
- Page 23 PARTS MANUAL Dust Collector Manual...
- Page 24 PARTS MANUAL Dust Collector Manual...
- Page 25 GENERAL SAFETY Dust Collector Manual...
- Page 26 PARTS MANUAL Dust Collector Manual...
- Page 27 GENERAL SAFETY Dust Collector Manual...
- Page 28 PARTS MANUAL Item No. Part Number Description Qty. 2844 RAIL CLAMP 6040-1.5 HHCS, 1/2-13 X 1.50 GR .5 6040-2.25 HHCS, 1/2-13 X 2.25 GR .5 6040-2075 HHCS1/2-13 X 2.75 GR .5 6112 FW 9/16 ID 1-3/8 OD 6151 1/12” LOCK WASHER 6406 1/2-13 LOCKNUT 8412-1...
-
Page 29: Notes
NOTES Dust Collector Manual... -
Page 30: Warranty
The product must have been purchased resulting from the installation or removal of this directly from Minnich or from an authorized product from any installation, any unauthorized Minnich reseller. tampering with this product, any repairs at-... -
Page 31: Parts Ordering Online
Scan for Helpful Videos! WE ACCEPT THE FOLLOWING CARDS! NON-DEALER AND INTERNATIONAL COSTUMERS: Contact Minnich Manufacturing through the following num- ber to locate a dealer near you. (419-903-0010) All orders are treated as Standard Orders and will ship the same day if received prior to...
Need help?
Do you have a question about the A-1CL and is the answer not in the manual?
Questions and answers