Advertisement
Available languages
Available languages
Quick Links
π
H-1903
HEAVY DUTY
GLUE GUN
1.
Fasten output control adjuster.
2. Plug in to a 110 volt outlet.
3. Insert glue stick into back of gun.
4. Pull trigger several times until glue is set firmly into
the inlet tube.
5. Turn ON/OFF switch on.
6. Adjust temperature knob to desired temperature.
7. Allow 3 minutes to warm up gun and glue stick.
8. Apply appropriate amount of glue by squeezing
trigger.
9. The output volume of glue can be adjusted by
turning the output control adjuster. Turn clockwise for
less glue and counterclockwise for more.
NOTE: Use short nozzle for general use or long
nozzle for harder to reach areas.
PAGE 1 OF 6
1-800-295-5510
uline.com
Small Wire
Support Stand
Temperature
Wire
Support Stand
OPERATION
Output Control
Adjuster
Knob
ON/OFF Switch
10. Bond surfaces by pressing together within 15
seconds after applying hot glue. For best results,
surfaces should be clean of any oil and dirt.
11. Always use the provided wire support stand in
between uses when gun is plugged in.
12. Never lay gun on its side while it is still hot.
13. After use, always switch gun to off, unplug gun and
use provided wire support until gun has cooled
before storing.
14. Never pull glue sticks out of gun.
15. If glue drips excessively, replace the nozzle. To
change, heat the gun for a minute until glue is
softened enough to remove the nozzle. While
wearing gloves, use a wrench to remove the old
nozzle. Flush glue through the gun and attach the
new nozzle.
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
0421 IH-1903
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for U-Line H-1903
Summary of Contents for U-Line H-1903
- Page 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. π H-1903 1-800-295-5510 uline.com HEAVY DUTY GLUE GUN Output Control Adjuster Small Wire Support Stand Temperature Knob Wire Support Stand ON/OFF Switch OPERATION Fasten output control adjuster. 10. Bond surfaces by pressing together within 15 seconds after applying hot glue.
- Page 2 SAFETY • Keep out of reach of children. • When inserting glue sticks into a hot glue gun, avoid using too much force. This can cause hot glue to • Never touch the nozzle of the gun or hot melted discharge unexpectedly from nozzle or flow back glue.
- Page 3 π H-1903 800-295-5510 uline.mx PISTOLA DE SILICÓN PARA USO PESADO Ajustador de Control de Salida Soporte de Alambre Pequeño Perilla de Temperatura Soporte de Alambre Interruptor de Encendido/ Apagado (ON/OFF) FUNCIONAMIENTO 1. Coloque el ajustador de control de salida. 10. Una las superficies presionándolas una contra la otra durante 15 segundos tras aplicar el pegamento 2.
- Page 4 SEGURIDAD • Mantenga el artículo fuera del alcance los niños. • Al insertar barras de pegamento en una pistola de silicón caliente, evite ejercer mucha fuerza. Esto • Nunca toque la boquilla de la pistola o el puede ocasionar que el pegamento caliente salga pegamento caliente derretido.
- Page 5 π H-1903 1-800-295-5510 uline.ca PISTOLET À COLLE ROBUSTE Régleur de puissance de sortie Petit support en métal Bouton de température Support en métal Interrupteur marche/arrêt FONCTIONNEMENT Fixez le régleur de puissance de sortie. 10. Collez les surfaces en les pressant ensemble dans les 15 secondes suivant l'application de la colle 2.
- Page 6 SÉCURITÉ • Tenir hors de la portée des enfants. • Lorsque vous insérez des bâtons de colle dans un pistolet à colle chaude, évitez d'employer une trop • Ne touchez jamais à la buse du pistolet ou à la grande force. La colle chaude pourrait ainsi se colle chaude.
Need help?
Do you have a question about the H-1903 and is the answer not in the manual?
Questions and answers