Related Manuals for ATV MOW
Summary of Contents for ATV MOW
- Page 1 ATV FLAIL MOWER Briggs & Stratton Engine OPERATION MANUAL ATV MOW 3730 Harmony Way Harcourt Victoria 3453 1300 121 131 | sales@atvmow.com.au...
- Page 2 INDEX Section: Description: Page No: Introduction HSE Information Sheet In the Interest of Safety: DO NOT In the Interest of Safety: DO Instruction & Warning Decals Operating Instructions And Adjustments Initial Check Drawbar Adjustment Mower Cutting Height Starting The Engine Forward Speed Stopping The Mower Transport Position...
- Page 3 Flail mower incorporates easy height adjustment, and a full width anti-scalping roller to avoid damage to machine and sward. The mower is constructed from 4mm steel for added strength; all fittings are of high quality to ensure years of trouble free use. Different wheel locations are available for the ATV Flail Mower...
- Page 4 1. Some weight is transferred from the trailer onto the ATV draw-bar; 2. The draw-bar has a swivel hitch and the ATV a ball hitch having a large head to neck ratio. This makes it easier for the draw-bar hitch to swivel and cope with undulating ground;...
- Page 5 Read the manufacturer’s instruction book and take note of the safety advice given; Choose an ATV with enough power for the work you want it to do. four-wheel drive will give better traction and mobility and may provide a margin of safety;...
-
Page 6: In The Interest Of Safety: Do
－ 6. DO Be aware components can be hot after operation － 7. DO Follow any towing guidelines stated by ATV manufacturer. － 8. DO Show some caution when filling the tank with petrol, especially if engine components are hot. - Page 7 INSTRUCTION / WARNING DECALS KEEP WHEEL NUTS TIGHT CHECK DAILY REFER TO THE OPERATORS MANUAL FOR CORRECT TYRE INFLATION PRESSURE OBSERVE TOWING VEHICLE MAX TOWING LIMITS OR TRAILER MAX WEIGHTS ATTENTION Your Responsibilities Before Operating this Machine are: (A) Read, understand and follow the safety procedures manual (B) Train operators before using &...
-
Page 8: Initial Check
The above decals should be located on your ATV – Flail Mower. If any of the above decals are not located on your ATV or are damaged in damaged in any way contact for some replacement decals before use. OPERATING INSTRUCTIONS AND ADJUSTMENTS The ATV FLAIL MOWER is designed to give safe and dependable service if operated according to instructions and intended use. -
Page 9: Drawbar Adjustment
5.2 DRAWBAR ADJUSTMENT The drawbar attachment height of the towing vehicle can vary. To accommodate adjustment, a screw link is located beneath the drawbar. This should be lengthened or shortened so that the cutting deck is horizontal to level ground. (This ensures a better cutting efficiency) TO ADJUST 1. -
Page 10: Starting The Engine
Observing all the precautions mentioned above in ‘Starting the mower’. REMOTE THROTTLE CONTROL When a remote throttle control option is fitted, normally to the rear carrier frame of an ATV or other suitable site on the towing vehicle, it gives the operator the facility of controlling the mower engine... -
Page 11: Forward Speed
from the operating position. The facility is most beneficial when moving from one cutting site to another close to it, by reducing the engine revs to allow the mower flails to come to rest, no harm will be caused to the mower or ground surface during transport, often over rough or difficult terrain when stones and loose objects may be encountered. - Page 12 Never move from one site to another with the engine running. Please note the ATV – Flail Mower is not road legal, and should not be used on public roadways 5.8 ANTI-SCALPING ROLLER/SIDE SKIDS The main purpose of the anti-scalping roller is to prevent damage. If a wheel drops into a hole, or there is uneven ground between the wheels, the roller takes the weight of the mower, avoiding the flails scalping the ground;...
-
Page 13: Maintenance
MAINTENANCE Maintenance Schedule Maintenance Operation: Hourly Daily Weekly Seasonal ● ● ● ● Engine (See Engine Manufacturers Manual) ● ● ● ● Remove Excess Crop Gathered on Deck Remove Excess Crop Wrapped around ● ● ● ● Rotor Ends ● ●... - Page 14 6.3 VISUAL CHECK Make a visual check around the mower, check for missing / loose parts or damaged / worn components. All-faults must be either repaired or replaced. 6.4 TYRE PRESSURES 6.5 ROTOR BEARING INSPECTION Rotate rotor shaft by hand and feel for any roughness in the bearings. Also try to pull the shaft from side to side to see if any movement is found.
- Page 15 6.9 ROTOR FLAIL MAINTENANCE The ATV Mow range has Forged Hammers designed to last a long time. However, when breaking or losing hammer, it is important to replace it immediately. Failure to do this can cause serious unbalancing problems. (Always use spare parts) At the time of replacement, the opposite hammer on the rotor should be checked for wear.
- Page 16 ATV FLAIL MOWER PART LIST...
- Page 17 ATV FLAIL MOWER ASSEMBLY Part No. Name & Specifications GB5783-86 Blot M12x30 GB93-87 Spring Washer 12 GB97.1-85 Plain Washer 12 MFP120.00.106 Fixing Sleeve GB894.1-85 Circlip 35 GB893.1-86 Circlip 62 GB278-89 Bearing 6007Z MFP120.00.152 Driving Belt Wheel MFP120.00.017 Clutch GB1096-79 Key 6.3x7x50 MFP120.00.018...
- Page 18 ATV FLAIL MOWER ASSEMBLY Part No. Name & Specifications EF100.00.101 Sleeve RK120.114A Blade GB5783-86 Blot M12x80 EF100.00.122 Baffle EF100.00.121 Baffle MFP120.00.109 Shaft MFP120.00.024 Protecting Bracket MFP120.00.116 Tension Spring UC207-Z Bearing Seat 90207 GB13871-94 Oil seal FB55x80x8 RK120.109 Oil-sealing Sleeve GB1152-89 Oil Cup M8x1 MFP120.00.036...
- Page 19 ATV FLAIL MOWER ASSEMBLY Part No. Name & Specifications MFP120.00.107 Driving Belt Wheel JB/T7934Z3 Swellable Sleeve GB12732 Belt 1067 GB5783-86 Bolt M6x16 GB93-87 Spring Washer 6 GB97.1-85 Plain Washer 6 GB62-88 Butterfly Nut M6 MFP120.00.111 Cover Plate MFP120.00.011 Protecting Cover...
- Page 21 ATV FLAIL MOWER WHEEL PARTMENT ASSEMBLY Part No. Name & Specifications GB1152-89 Oil Cup M6 GB6170-86 Nut N12 GB97.1-85 Plain Washer 12 MFP120.00.038-A Protection Casting Weldment GB5783-86 Bolt M12x35 MFP120.00.039 Handle GB276-94 Bearing 61904 TR200.00.123 Bearing Seat GB301-95 Bearing 51104...
- Page 23 ATV FLAIL MOWER TRACTION ASSEMBLY Part No. Name & Specifications GB1152-89 Oil Cup M6 GB6170-86 Nut N12 GB97.1-85 Plain Washer 12 MFP120.00.038-A Protection Casting Weldment GB5783-86 Bolt M12x35 MFP120.00.039 Handle GB276-94 Bearing 61904 TR200.00.123 Bearing Seat GB301-95 Bearing 51104 GB70-85 Screw M8x30 TR200.00.120...
- Page 25 ATV FLAIL MOWER PART LIST Part Code Part Name Note ATH120.011 Cover Weldment UC207 Bearing Set ATH120.005 Blade Axle Assy ATV120.106 Bush GB/T 13871.1-2007 Seal Ring GB/T 95-2002 Flat Washer 24*13.5*2.5 GB/T93-1987 Spring ATV120B.103 Slide Plate R ATV120B.104 Slide Plate L ATV120B.105...
- Page 26 ATV FLAIL MOWER PART LIST Part Code Part Name Note Bakelite Bolt Rubber Bolt M10-22 ATV120B.019 Triangle Weldment GB/T 95-2002 Flat Washer GB/T 859-1987 Spring Washer GB/T 859-1987 Spring Washer at120.102 Shaft GB/T 95-2002 Flat Washer GB/T 889.1-2000 Locking Nut M16...
- Page 27 ATV FLAIL MOWER PART LIST Part Code Part Name Note 6-DZF-12 Buttery KSP120.031A Cover Weldment for Buttery GB／T 5780-2016 Bolt M6*50 M6×50 GB/T 889.1-2000 Locking Nut M8 GB/T 5783-2000 Bolt M8*20 M8×20 ATH120.002 Transmission Part ATMS120.003 Tyre Part ATJ120.002 Inn-Out Tube Parts AT120.016...
- Page 29 ATV FLAIL MOWER PART LIST Part No. Part Name Note AT120.110 Active Wheel Fixation GB/T 95-2002 Flat Washer GB/T 859-1987 Spring Washer 10 7/16-20X35 Jiangdong GB/T 5783-2000 Bolt 3/8-24X35 Loncin GB/T 95-2002 Flat Washer GB/T 859-1987 Spring Washer 6 GB/T 5781-2000 Bolt M6×16...
- Page 30 ATV FLAIL MOWER PART LIST Part No. Part Name Note GB 893.1-86 Circlip for Hole AT120.111 Tension Wheel ATV120.108 Driven Wheel Belt Belt BX1067 GB/T 70.1-2000 Stud M8×20 GB/T 1096-2003 Key B6*6*40 B6×6×40 ATV120B.018 Belt Cover Weld...
- Page 32 ATV FLAIL MOWER PART LIST Part No. Part Name Note ATMP120.011A Trailer Wheel Arm Weldment (L) ATMP120.012A Trailer Wheel Arm Weldment (R) AT120.501 Tyre 16*6.5-8 GB/T 276-94 Deep Groove Ball Bearing 6205-2Z GB/T 96.1-2002 Big Washer 12 37*13*3 GB/T 859-1987...