Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Monkey Vision MOMETER PRO
Summary of Contents for Monkey Vision MOMETER PRO
- Page 1 Monkey MOMETER FACIAL RECOGNITION•ACCESS CONTROL QUICK START GUIDE...
- Page 2 INTRODUCTION The Monkey MOMETER PRO has been specifically developed to help Australians take the necessary steps to only allow the right people onto your site With accurate, contactless scanning and facial the option of activating personal registration and access control, it’s the perfect solution for of fices, hotels, buildings,...
- Page 3 5. Please don’t plug audio equipment, alarms and other external interfaces or terminals directly to the unit. 6. The Monkey Mometer Pro works best in room temperature between -100C and +550C and relative humidity between 10% - 90%. But if you’re working somewhere the room temperature is below 00C or above 300C you should seriously consider looking for another job.
- Page 4 TO BUILD YOUR STAND: THE STAND HAS THREE MAIN PARTS: A BASEPLATE AND TWO UPRIGHT POSTS. (YOU SHOULD ALSO HAVE A POWER CABLE, TWO BACK PLATES, A LARGE SPACER RING AND 20 BOLTS) STEP 1 STEP 2 STEP 3 The upright posts have four holes Attach the baseplate to one of the Carefully place the other post in each end.
- Page 5 Tighten the nut as much as the bottom of the the hole at the top of you can by hand. If you like, Monkey MOMETER PRO your stand one at a time you can tighten further with and remove it.
- Page 6 You’re good to go! The Monkey MOMETER PRO will tell you if something is wrong – like if you need to stand closer to or further STEP 6 away from the unit, or if you need to clear things away from your f...
- Page 7 CONNECTOR INTERFACE INTRODUCTION 1. USB 5V DM DP GND A and B Normal open, default normal open, identification passed-connection, (alarm output 2) 2. Access Control (output) C and D Normal close, default normal close, identification passed-disconnection, (alarm output 2) 3. Reset Key Hard reset 4.
- Page 8 Mometer. To find the IP address of your Monkey Mometer, look at the bottom left of the Monkey Mometer's screen. If you have purchased a Monkey Vision 4G Ranger, you will connect to your Monkey Mometer via WiFi and the IP address is 192.168.100.8...
- Page 9 If everything has gone to plan you should see the main screen as below. STEP 2 Click on “Access Control” along the top of the screen. Live View Play Back Access Control Camera Settings Directory Logout Face Recognition Region CONT. monkeyvision.com.au...
- Page 10 Live View Play Back Access Control Camera Settings Directory Logout To capture the faces of people visiting your site, we recommend you set up folders on your connected PC to store Directory these images. ˇ Local Disk Click on Directory across the top Record Path Open directory C:\webclient2\videos...
-
Page 11: Door Access
Click on “Door Access”, Live View Play Back Access Control Camera Settings Directory Logout then select the access mode you want from the Access Control Door Access Save drop down list. Face Recognition Temperature Access Control Face Detection Temperature & Face Temperature &... - Page 12 To enable or disable Live View Play Back Access Control Camera Settings Directory Logout face-mask detection, click on “Face Mask Detection” Access Control Face Mask Detection and select from the Save Face Mask Detection drop down list. Face Detection Disable Wearing Mask Alarm Door Access Not Wearing Mask Alarm...
- Page 13 To set up Face Detection, Live View Play Back Access Control Camera Settings Directory Logout you need to create a Whitelist, click on Face Library, and then Face library configuration Access Control click on the settings icon next to List Export Import Face Detection...
- Page 14 Single Add Click on confirm in the Single Add dialogue box. ˇ Add Person New face ˇ Directory Picture Source Cancel Confirm Click on the plus sign at the top of the photo box that opens up ⁺ at that step, note the settings required for the photo, Support maximum size (256KB)
- Page 15 This folder will open on your computer, you can then search for folders on your computer where photos may already be stored. You can click through the default folder to find people who have attended your site – the best photo that can be used from existing images is one where the person was in good light and stood approx.
- Page 16 Double click the photo, Live View Play Back Access Control Camera Settings Directory Logout and then edit the persons details as per below. Whitelist Return to Face Library Access Control To add more than one person, Results Face Detection Refresh Batch Add Single Add Delete...
- Page 17 Click on Batch Add, click on the folder icon, you Batch Add will go to a standard Explorer window to find the photo files. Click on the files you want to import and then click on the “Import” command at the bottom right of screen.
- Page 18 Live View Play Back Access Control Camera Settings Directory Logout Access Control Access Log Results Face Detection Door Access Derived form Refresh Face Mask Detection List Registered Face Library Name Time & Date Degree of Recognition Temperature Unit Temperature Monitoring White list whiteListGroup Nick...
- Page 19 Live View Play Back Access Control Camera Settings Directory Logout To identify someone where the name field is blank, Intelligent configuration Access Log double click on that entry Results Face Detection Details to see who it was by revealing Door Access Derived form Refresh Face Mask Detection...
- Page 20 The information contained within this document provides the user with all the practical information required to safely set-up and operate the Monkey MOMETER PRO. Without written permission, no unit or individual may in any way extract, copy, translate or modify all or part of this manual.
Need help?
Do you have a question about the MOMETER PRO and is the answer not in the manual?
Questions and answers