Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Amit RB-MVB/AN02
Summary of Contents for Amit RB-MVB/AN02
- Page 1 RB-MVB/AN02 MVB analyser Operation manual Version 1.00 rb-mvban02_g_en_100...
- Page 2 RB-MVB/AN02 AMiT, spol. s r. o. does not provide any warranty concerning the contents of this publication and reserves the right to change the documentation without obligation to inform any body or authority about it. This document can be copied and redistributed under following conditions: 1.
-
Page 3: Table Of Contents
RB-MVB/AN02 Contents History of revisions ..................4 Related documentation ................... 4 Definition of used abbreviaions ............5 Definition of used terms ..............6 Introduction ..................7 Technical parameters ................8 4.1. Dimensions ....................10 4.2. Recommended drawing symbol ..............11 Product marking ................ -
Page 4: History Of Revisions
RB-MVB/AN02 History of revisions Document name: rb-mvban02_g_en_100.pdf Revision Date Author of change Changes 4. 10. 2016 Petrovský J. New document Related documentation RB-MVB/AN02 – MVB analyser – Programmers manual file: rb-mvban02_1_ms_en_100.pdf rb-mvban02_g_en_100 4/30... -
Page 5: Definition Of Used Abbreviaions
RB-MVB/AN02 1. Definition of used abbreviaions Bus Administrator Electrical Middle Distance Medium Attachment Unit Multifunction Vehicle Bus Message Data Process Data To Be Defined Train Communication Network 5/30 rb-mvban02_g_en_100... -
Page 6: Definition Of Used Terms
RB-MVB/AN02 2. Definition of used terms Bus Administrator MVB device with Bus Administrator functionality is able to work as MVB bus Master. This function supposes the device is able to transfer the process data and reports as well as transmit and receive the Device Status type information. -
Page 7: Introduction
RB-MVB/AN02 3. Introduction RB-MVB/AN02 is an MVB analyser. Analyser contains doubled MVB interface in ESD and EMD connection, Ethernet interface and BNC connector for triggering. Device is supplied from factory only with loader. Before first use all required domains must be loaded into device (see Programming manual). -
Page 8: Technical Parameters
RB-MVB/AN02 4. Technical parameters MVB interface MVB Standard IEC 61375-3-1: 2012 1 × EMD, 1 × ESD Number of MVB lines Number of MVB channels MVB Classification Class 1 Galvanic isolation Insulation strength 500 V AC / 1 minute *) Physical layer EMD, ESD 1.5 Mbps 0.01 %... - Page 9 RB-MVB/AN02 Dangerous Unit overall mass of plastics 144 g materials Included mass of self-extinguishing 144 g plastics Module does not contain PUR, PVC, Asbestos Module complies 2011/65/EU (ROHS) 1907/2006EU (REACH) -40 °C to 70 °C Temperatures Operating temperature -40 °C to 70 °C...
-
Page 10: Dimensions
RB-MVB/AN02 4.1. Dimensions RB-MVB/AN02 TYPE: S/N: xxxxxxx MAC: xx-xx-xx-xx-xx-xx LDR: POWER: 24 V DC / 0.6 A WEIGHT: 0.87 kg TEST: OK-JE HiPot: HiPot - OK DATE: 09.06.2015 Fig. 1 - RB-MVB/AN02 mechanical dimensions in mm rb-mvban02_g_en_100 10/30... -
Page 11: Recommended Drawing Symbol
RB-MVB/AN02 4.2. Recommended drawing symbol Following drawing symbol is recommended for RB-MVB/AN02 analyser. RB-MVB/AN02 Trigger Ethernet MVB ESD MVB ESD MVB EMD MVB EMD Fig. 2 - Recommended drawing symbol for RB-MVB/AN02 11/30 rb-mvban02_g_en_100... -
Page 12: Product Marking
RB-MVB/AN02 5. Product marking Analyser RB-MVB/AN02 is fitted with producer type label on its side. RB-MVB/AN02 TYPE: S/N: xxxxxxx MAC: xx-xx-xx-xx-xx-xx LDR: POWER: 24 V DC / 0.6 A WEIGHT: 0.87 kg TEST: OK-JE HiPot: HiPot - OK DATE: 09.06.2015 Fig. -
Page 13: Producer Type Label
RB-MVB/AN02 TYPE: S/N: xxxxxxx MAC: xx-xx-xx-xx-xx-xx LDR: POWER: 24 V DC / 0.6 A WEIGHT: 0.87 kg TEST: OK-JE HiPot: HiPot - OK DATE: 09.06.2015 Fig. 4 - Example of AMiT type label 13/30 rb-mvban02_g_en_100... -
Page 14: Conformity Assessment
RB-MVB/AN02 6. Conformity assessment The equipment meets the requirements of NV616/2006 Czech Government Decree. The conformity assessment has been carried out in accordance with harmonized standard EN 50121-3-2:2006. Tested in accordance Type of test Classification with standard EN 55011:2009 Industrial, scientific and medical Complies equipment –... -
Page 15: Other Tests
RB-MVB/AN02 6.1. Other tests This product has been assessed and approved for use in railway applications according to standards: Tested in accordance Type of test Classification with standard Railway applications – Electronic EN 50155:2007 Complies equipment used on rolling stock Railway applications –... -
Page 16: Power Supply
RB-MVB/AN02 7. Power supply Analyser RB-MVB/AN02 can be powered only by DC power supply +24 V. Fig. 5 - Power supply connector location Connector Connector type: WAGO 769-103/021-000 wiring Connector Signal Description Module chassis Power supply, ground Power supply, +24 V DC... -
Page 17: Communication Lines
RB-MVB/AN02 8. Communication lines Analyser RB-MVB/AN02 disposes with MVB interfaces adapted for EMD (Electrical Middle Distance) and ESD (Electrical Short Distance). Coupling connector is D-sub DE-9 plug and socket, fixed to counterpart by bolt with M3 thread. Connectors are internally concatenated. -
Page 18: Mvb-Emd
RB-MVB/AN02 8.2. MVB-EMD Terminating resistor for EMD is part of analyser. It is activated through external termination module TRM-MVB/F EMD or TRM-MVB/M EMD. X6, X7 Fig. 7 - Location of MVB-EMD connectors Connector Connector type: D-sub DE-9, socket wiring Connector... -
Page 19: Mvb Line State Indication
RB-MVB/AN02 8.2.1 MVB line state indication State of MVB line is indicated by 8 LEDs on front panel. Following table describes meaning of individual LEDs. Fig. 8 - Detail look on front panel LEDs (MVB LEDs) Colour Green Green Green... -
Page 20: Ethernet
RB-MVB/AN02 8.3. Ethernet The 10/100 Mbps Ethernet interface allows connecting of RB-MVB/AN02 analyser to LAN network. Fig. 9 - Ethernet connector location Connectors Connector type: RJ45, socket wiring Signal Description Data transmission, signal + Data reception, signal + Data transmission, signal - –... -
Page 21: Ethernet Line State Indication
RB-MVB/AN02 8.3.1 Ethernet line state indication State of Ethernet line is indicated by 2 LEDs on front panel. Following table describes meaning of individual LEDs. Fig. 11 - Detail look on front panel LEDs (Ethernet LEDs) Colour Green Green Status... -
Page 22: Inputs/Outputs
RB-MVB/AN02 9. Inputs/outputs 9.1. Trigger output Analyser RB-MVB/AN02 is equipped with triggering output with BNC connector. Output signal has a 5 V level; output impedance is 50 Ω. The function is given by the software. Fig. 12 - Trigger output connector location... -
Page 23: Indications And Settings
RB-MVB/AN02 10. Indications and settings 10.1. System LEDs Indication of analyser status is provided by two LEDs in the upper part of front panel. Following table describes meaning of individual LEDs. Fig. 13 - Detail look on front panel LEDs (System LED) -
Page 24: Service Mode And Factory Setting
RB-MVB/AN02 10.2. Service mode and factory setting Service mode is started and factory settings are restored through RESTORE button. To press the button, use a tool with diameter max. 1.5 mm (e.g. match, or ballpoint refill). Service mode To restore the factory setting press and hold the RSTR button while analyser starts up. -
Page 25: Mounting, Installation Rules
RB-MVB/AN02 10.3. Mounting, installation rules MVB analyser is intended for mounting on base plate with two 6 mm diameter holes. Analyser could be mounted in any position. Fig. 15 - Mounting holes 25/30 rb-mvban02_g_en_100... -
Page 26: Ordering Information And Completion
RB-MVB/AN02 11. Ordering information and completion Complete unit – see chapter 11.1 Completion MVB analyser RB-MVB/AN02 11.1. Completion RB-MVB/AN02 Part Quantity MVB analyser Connector counterpart WAGO 769-103/021-000 Insulation testing protocol Certificate of product quality and completeness Routine testing protocol rb-mvban02_g_en_100... -
Page 27: Packing
RB-MVB/AN02 12. Packing Packing The analyser is wrapped in two layers of bubble wrap. Wrapped analyser is stored in a paper box. Package dimensions are listed in chapter 4. Technical parameters. Label Sticker on the box contains following information: Item... -
Page 28: Storing
RB-MVB/AN02 13. Storing To prevent damage of the device, follow these rules. Product Product in original packaging must be stored under the conditions specified in in a package chapter 4. Technical parameters. Product must not come into contact with water, oil or any other liquids that can damage the packaging. -
Page 29: Maintenance
RB-MVB/AN02 14. Maintenance Device requires no periodic control nor maintenance. Cleaning Depending on equipment usage, the dust is to be removed occasionally from equipment. The equipment can be cleaned by dry soft brush or vacuum cleaner, only when turned-off and disassembled. -
Page 30: Waste Disposal
RB-MVB/AN02 15. Waste disposal Electronics The disposal of electronic equipment is subject to the regulations on handling disposal electrical waste. The equipment must not be disposed of in common public waste. It must be delivered to places specified for that purpose and recycled.
Need help?
Do you have a question about the RB-MVB/AN02 and is the answer not in the manual?
Questions and answers