Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Amit RRU-WTB/AN01
Summary of Contents for Amit RRU-WTB/AN01
- Page 1 RRU-WTB/AN01 WTB analyser Operation manual Version 1.00 rru-wtban01_g_en_100...
- Page 2 RRU-WTB/AN01 AMiT, spol. s r.o. does not provide any warranty concerning the contents of this publication and reserves the right to change the documentation without obligation to inform any body or authority about it. This document can be copied and redistributed under following conditions: 1.
-
Page 3: Table Of Contents
RRU-WTB/AN01 Contents History of revisions ..................4 Related documentation ................... 4 Definition of used abbreviations ............5 Definition of used terms ..............6 Introduction ..................7 Technical parameters ................8 4.1. Dimensions ....................11 4.2. Recommended drawing symbol ..............12 4.3. -
Page 4: History Of Revisions
RRU-WTB/AN01 History of revisions Document name: rru-wtban01_g_en_100.pdf Author: Jiří Březina Revision Date Changes 14. 8. 2014 New document Related documentation Programmers manual WTB analyser Programmer’s manual file: tcn-wtb-an_ms_en_xxx.pdf Application Note AP0037 – Principles of using Ethernet network file: ap0037_en_xx.pdf rru-wtban01_g_en_100... -
Page 5: Definition Of Used Abbreviations
RRU-WTB/AN01 1. Definition of used abbreviations Bus Administrator Electric Middle Distance Medium Attachment Unit To Be Defined Train Communication Network Wire Train Bus 5/28 rru-wtban01_g_en_100... -
Page 6: Definition Of Used Terms
RRU-WTB/AN01 2. Definition of used terms Bus Administrator MVB device with Bus Administrator functionality is able to work as MVB bus Master. This function supposes the device is able to transfer the process data and reports as well as transmit and receive the Device Status type information. -
Page 7: Introduction
RRU-WTB/AN01 3. Introduction RRU-WTB/AN01 is WTB bus analyser, hereinafter analyser or WTB analyser. Analyser is intended to be mounted in to the 19“ subrack, or it could be mounted in to other suitable frame structure. Analyser is equipped with doubled WTB interface and working Ethernet line with M12 connector. -
Page 8: Technical Parameters
RRU-WTB/AN01 4. Technical parameters Number of WTB lines 1 (doubled line) 16 × LED Operation indication Galvanic separation Yes, 1000 V AC / 1 minute Fritting 1 Mbps 0,01 % Communication rate Max. number of devices Max. segment length without repeater 860 m 120 Ω... - Page 9 RRU-WTB/AN01 Mechanics Mechanical design Compact aluminium tube, anodized black Front and rear panel made of aluminium alloy with anti-corrosion coating Into 19“ subrack Mounting Ingress protection rate IP30 – netto 1.55 kg ±5 % Weight – brutto 1.85 kg ±5 % Dimensions in standard units (w ×...
- Page 10 RRU-WTB/AN01 Safety The equipment meets the SWSIL0 classification according to EN 50128:2011 Railway applications – Communications, signalling and processing systems – classification Software for railway control and protection systems. The equipment meets the SIL0 classification according to EN 50129:2003 Railway applications –...
-
Page 11: Dimensions
RRU-WTB/AN01 4.1. Dimensions 168,5 Fig. 1 - Analyser mechanical dimensions 11/28 rru-wtban01_g_en_100... -
Page 12: Recommended Drawing Symbol
RRU-WTB/AN01 4.2. Recommended drawing symbol Following drawing symbol is recommended for RRU-WTB/AN01 module. RRU-WTB/AN01 Ethernet WAGO 769-663 D-sub DE-9 24 V WTB A1 D-sub DE-9 WTB A2 D-sub DE-9 WTB B1 D-sub DE-9 WTB B2 Fig. 2 - Recommended drawing symbol... -
Page 13: Block Diagram
WTB B1 WTB B2 Power Ethrenet interface interface 5 V ss. 1.2 V ss. 1.8 V ss. DDR2 FPGA 2.5 V ss. 24 V ss. 5 V ss. Power Power supply supply Fig. 3 - RRU-WTB/AN01 analyser block scheme 13/28 rru-wtban01_g_en_100... -
Page 14: Conformity Assessment
RRU-WTB/AN01 5. Conformity assessment Providing that RRU-WTB/AN01 analyser is correctly used, it will comply the requirements of Czech governmental decree NV616/2006. The conformity assessment has been carried out in accordance with harmonized standard EN 50121-3-2:2006. Tested in accordance Type of test... -
Page 15: Other Tests
RRU-WTB/AN01 5.1. Other tests RRU-WTB/AN01 WTB analyser has been assessed and approved for use in railway applications according to standards: Tested in accordance Type of test Result with standard EN 50155:2007 Electronic equipment used on rolling stock. Complies Electromagnetic compatibility (EMC) –... -
Page 16: Power Supply
RRU-WTB/AN01 6. Power supply The RRU-WTB/AN01 WTB analyser can be powered by 24 V DC vehicle on-board network. 6.1. Powering from DC network Power supply is connected to X1 WAGO 769-663 (X-COM®), plug. Fig. 4 - Power supply connector location... -
Page 17: Communication Lines
RRU-WTB/AN01 7. Communication lines 7.1. WTB RRU-WTB/AN01 WTB analyser has available a WTB interface with doubled line, according to IEC 61375-1 ed. 2 standard. Both lines are connected through D-sub DE-9 connectors. Connectors are fitted with M3 threaded nuts, that secures cable against extraction or falling off due to vibrations. -
Page 18: Wtb Line State Indication
RRU-WTB/AN01 Connector type: D-sub DE-9, socket Connector Signal wiring on RRU-WTB/AN01 X4, X6 WTB line positive wire WTB line negative wire Not used Not used Not used Not used Not used Not used Not used 7.1.1 WTB line state indication Indication of WTB line state is provided by 16 LEDs in the middle part of front panel. -
Page 19: Ethernet
RRU-WTB/AN01 7.2. Ethernet The Ethernet 100 Mbps interface allows the WTB analyser to connect to LAN network. Ethernet interface is fitted with M12 connector according to IEC 61375-3-4:2014. Fig. 7 - Location of Ethernet line connector M12 type M12 type connector according to EN 61375-3-4:2014... -
Page 20: Ethernet Line State Indication
RRU-WTB/AN01 7.2.1 Ethernet line state indication Indication of Ethernet line state is provided by two LEDs, located above the RJ45 connector. Fig. 8 - Front panel LEDs detail (Ethernet) Meaning of Color Meaning Green Analyser connected to the Ethernet network... -
Page 21: Indications And Settings
RRU-WTB/AN01 8. Indications and settings 8.1. System LEDs Fig. 9 - Front panel LEDs detail (System LEDs) LED colors Color Yellow Green Green Meaning of Status Meaning Lights Power supply voltage indication Blinks, T = 2 s Operation state Blinks, T = 200 ms... -
Page 22: Service Mode And Factory Setting
RRU-WTB/AN01 8.2. Service mode and factory setting RSTR button is used to enter service mode and to restore factory settings. To press the button, use a tool with maximum diameter of 1.5 mm. Service mode To enter service mode press and hold the RSTR button during analyser start up. -
Page 23: Mounting, Installation Rules
9. Mounting, installation rules 9.1. Mounting instructions Analyser RRU-WTB/AN01 is intended to be mounted into 19“ subrack. After the analyser is put in to rack it must be fixed with four screws in plastic sleeves in four corners of front panel. - Page 24 RRU-WTB/AN01 Fig. 11 - Fixing, when mounting in to frame. Keep the free space at least 70 mm in front of WTB gateway for attaching the cables. It is very important to ensure that ambient temperature does not exceed the allowed limits.
-
Page 25: Holes For Mounting Into Frame
RRU-WTB/AN01 9.2. Holes for mounting into frame All dimensions are stated in mm. Fig. 12 - Mounting template for mounting into the frame 9.3. Installation rules PE terminal of power supply connector must be connected with local installation earthing terminal. -
Page 26: Ordering Information And Completion
RRU-WTB/AN01 10. Ordering information and completion 10.1. Ordering information WTB analyser RRU-WTB/AN01 Complete, see chapter Completion Connector WAGO769-103 Power supply connector counterpart counterparts 21038821405 Crimping M12 cable connector, D coding Crimping contacts to 21038821405 for AWG 24 – 28 09670007576... -
Page 27: Maintenance
RRU-WTB/AN01 11. Maintenance WTB analyser requires no periodic control, nor maintenance. Cleaning Time after time, with regard to way of using it is necessary to remove dust from device. The equipment can be cleaned in cut-off state and disassembled, by dry paintbrush or fine brush, alternatively by vacuum cleaner. -
Page 28: Waste Disposal
RRU-WTB/AN01 12. Waste disposal Electronics The disposal of WTB analyser is subject to the regulations on handling electrical disposal waste. Analyser must not be disposed together with common public waste. It must be delivered to places specified for that purpose and recycled.
Need help?
Do you have a question about the RRU-WTB/AN01 and is the answer not in the manual?
Questions and answers