Related Manuals for Incite Fire ekho EK-WL8-TRH
Summary of Contents for Incite Fire ekho EK-WL8-TRH
- Page 1 EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 1 of 22...
-
Page 2: Table Of Contents
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 2 of 22 CONTENTS GENERAL DESCRIPTION ...................... 3 TECHNICAL SPECIFICATIONS ........................4 FEATURES ..............................4 CONSTRUCTION ........................5 STRUCTURE ..............................7 INSTALLATION ........................9 MAIN APPLICATIONS .......................... 10 WIRING..............................11 ACCESS PERMISSION ........................12 NEW SYSTEM CREATING ........................... -
Page 3: General Description
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 3 of 22 GENERAL DESCRIPTION • The “wire to wireless” translator module EK-WL8-TRH/AU (further EK- WL8-TRH or WL8-TRH) is a device which interfaces the hard-wired Hochiki Enhanced Systems Protocol (ESP) loop to the Ekho wireless sys- tem. -
Page 4: Technical Specifications
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 4 of 22 TECHNICAL SPECIFICATIONS Loop Supply Voltage (low) from 17V to 32V Loop Pulse Voltage from 7 V to 9 V Quiescent Current 27mA (at 41V 22mA±20% Loop current (when polled) Radio frequency 918-926 MHz Radio signal modulation type... -
Page 5: Construction
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 5 of 22 • Two internal antennas • Operate up to 3 seconds with internal power source after 15 minutes of operating • OLED graphical display 96x64 dots embedded CONSTRUCTION In order to open the case please bend the latches, de- lete the two rivet snaps and remove the cover. - Page 6 EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 6 of 22...
-
Page 7: Structure
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 7 of 22 STRUCTURE EK-WL8-TRH board LOOP'S TERMINAL BLOCKS: used for connecting the translator to the analogue loop DISPLAY: used for configuring the wireless system Micro USB PORT: used for modifying the firmware with a computer via a micro-USB cable and for connecting to Streletz-Wizard software. - Page 8 EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 8 of 22 ANTENNA'S TERMINAL BLOCKS: can be used to replace the built-in an- tennas with external ones. In order to do that, please remove the existing antennas and insert coaxial cables from external 918 MHz antennas (con- nect the central conductor to socket "A").
-
Page 9: Installation
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 9 of 22 INSTALLATION Avoid installing the translator close to: equipment that uses large amounts of electrical current large metal objects, structures or metal ceiling structures fluorescent lighting fixtures computers, their peripheral and network cabling. If there are other translators or wireless system expander modules, keep a distance between them of at least 2 meters. -
Page 10: Main Applications
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 10 of 22 MAIN APPLICATIONS There is one Ekho subsystem in a loop Ekho device #1 Expander Hochiki Device#1 Ekho Hochiki subsystem Device#2 Main TRH Ekho device #2 Main control panel Hochiki Ekho device #3 Device#N... -
Page 11: Wiring
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 11 of 22 WIRING TRANSLATOR'S WIRING Before wiring the device, please keep in mind the following: refer to and follow national codes of wiring and cabling practice and other internationally recognized standards; loop terminals are polarity sensitive, so connect them according to the following instructions. -
Page 12: Access Permission
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 12 of 22 FINAL STEPS OF INSTALLATION Configure radio system either directly with translator’s keyboard/display system or with a personal computer. System configuring and programming will be described further in this manual. ATTENTION Due to limitation of short circuit isolators, the panel current should be limited to 2 Ampere. -
Page 13: New System Creating
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 13 of 22 NEW SYSTEM CREATING First of all, you should create central node (Main TRH) or a few central nodes if it's required of application. Create new WL8-TRH Main TRH WL8-TRH system? v x.x/RF v.y... -
Page 14: Choosing Protocol Type
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 14 of 22 CHOOSING PROTOCOL TYPE Radio WL8-TRH Configuration RSM-WTM Loop v x.x/RF v.y Maintenance HWL8-TRH Start Addr Short! PSW Change Prot.type Currently you have to use default protocol type named RSM-WTM. The pro- tocol type HWL8-TRH is for future use. -
Page 15: Changing The Start Address Of Devices In The Loop
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 15 of 22 WL8-TRH v x.x/RF v.y Password Are you Radio Delete Configuration --ADD NEW-- sure? Init 000 RR-V Loop Maintenance Info 001 Aur-TS Start Addr 002wl8-os etc. Please keep in mind that this command deletes a device from the configura- tion of the translator, but not from the configuration of the main control panel. -
Page 16: Addresses Cross-Mapping
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 16 of 22 ADDRESSES CROSS-MAPPING The Loop menu is used to show information about whole address table translator provides to the Hochiki loop. Also, it's possible to see the mapping between Hochiki and radio addresses. WL8-TRH Radio wl8-trh... -
Page 17: Parameter Editing
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 17 of 22 You can also see the address(es) occupied by every radio device: WL8-TRH Radio --ADD NEW-- Delete Configuration Loop Init v x.x/RF v.y Loop 000wl8-trh Maintenance address(es) Edit 001wl8-o Start Adrr 9,136 002wl8-ov... - Page 18 EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 18 of 22 Tamper Info Radio --ADD NEW-- Configuration WL8-TRH Enabled Edit Loop 000wl8-trh v x.x/RF v.y Maintenance Alarm sound Start Addr 001wl8-o Cont. tone Alarm mess. Pulse 1s/1s Pulse 2s/2s Dual 1s/1s Dual .4s/.4s Pulse .2s/1.3s...
-
Page 19: Maintenance
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 19 of 22 MAINTENANCE Maintenance menu (not for WL8-TRH(E)) allows you to see the state of wireless devices and send control commands: State Configuration ! 001wl8-o Tamper Control Maintenance ! 003wl8-in RF Link ! 001wl8-trh(e) Command... -
Page 20: Warranty
EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 20 of 22 In the "RF Link" mode WL8-TRH shows link quality with selected child de- vice according to next table: Wireless signal quality (S/N) Assessment < 10 dB Bad (no connection) 10 –... - Page 21 EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 21 of 22 APPENDIX A MENU, SUB-MENU AND COMMAND STRUCTURE Radio WL8-O WL8-TRH --ADD NEW-- Loop 000wl8-trh WL8-OH v x.x/RF v.y WL8-H Start Addr list devices Short! WL8-OS PSW Change WL8-OV Prot.type Device Press prog...
- Page 22 EK-WL8-TRH/AU WIRELESS TRANSLATOR MODULE STFV.425551.070-AU-UM rev. 4 20.08.2020 Page 22 of 22...