Page 4
Digital Voice Systems, Inc. shall not be liable for any errors or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual or the examples herein. The information in this document is subject to change without notice.
Page 5
END USER has requested a license, and any derivative works thereof, including modifications, enhancements and extensions made by or for Digital Voice Systems, Inc. (DVSI) and including circuit diagrams, timing diagrams, programmable logic software, logic diagrams, layouts, operating instructions and user manuals.
Page 6
Agreement shall be limited to 20% (twenty percent) of the fees paid by END USER for the particular Voice Codec or VC-20™ ATC-10b Vocoder Board which caused the damages or that is the subject matter of, or is directly related to, the cause of action.
Page 7
Agreement shall remain in full force and effect. 12.0 Notices complete sole 12.1 Any notices to DVSI which may be given hereunder shall be in writing and sent to: Littleton Road, Westford, MA., 01886, U.S.A. AMBE-1000™ Vocoder Chip User’s Manual Digital Voice Systems Inc., 234...
The Speech Compression Specialists VC-20™ - ATC-10b Introduction General Information The Digital Voice Systems, Inc. (DVSI) VC-20™ - ATC-10b voice codec is a full- duplex real-time voice processing board. The VC-20™ - ATC-10b contains proprietary software which implements the Advanced Multi-Band Excitation™...
5-14 should be disconnected. If the VC-™ - ATC-10b is generating the clocks and frames, then jumpers 1-4 should be connected, otherwise, they should be disconnected. VC-20 ATC-10b Vocoder Board User’s Manual Section 2 – VC-20 AMBE™ Vocoder Board Overview page 3...
Storage To insure maximum shelf life in long term storage, VC-20 AMBE™ Vocoder Board should be kept in a moisture controlled package at <40 C and <90% RH. page 4...
Section 6 – VC-20™ ATC-10b Vocoder Board Advanced Features VC-20-ATC-10b Connector Signals TXD3-0 TXD3-0 are the voice data signals from the VC-20™ - ATC-10b encoder. These signals changes state on each rising edge of TXCK. The 96 voice bits of each 20 ms voice frame are transmitted in 24 TXCK cycles (TXCK = 9.6 kHz), resulting in an...
Page 19
DTMF_DET is high. The data is synchronous with the rising edge of TXCK. This signal should be ignored when DTMF_DET is inactive. VC-20 ATC-10b Vocoder Board User’s Manual Section 6 – VC-20™ ATC-10b Vocoder Board Advanced Features page 9...
Section 6 – VC-20™ ATC-10b Vocoder Board Advanced Features GO The GO signal must be active to place the encoder in voice mode. This signal is sampled every 20 ms when FMEN is high. If this signal is active then the encoder outputs voice data on TXD during the next 20 ms frame.
Section 6 – VC-20™ ATC-10b Vocoder Board Advanced Features VC-20-ATC-10b DTMF Tone Data The VC-20-ATC-10b supports DTMF detection, transmission, and generation. The encoder detects and transmits DTMF tones, and the decoder decodes and generates DTMF tones, in support of standard telephony requirements In addition, if the VC-20™...
Additional Manuals Additional manuals may be downloaded for DVSI’s web sit www.dvsinc.com VC-20 ATC-10b Vocoder Board User’s Manual Digital Voice Systems, Inc. 234 Littleton Road Westford, MA 01886 USA Phone: (978) 392-0002 Fax: (978) 392-8866 email: info@dvsinc.com...
5.5 mm 41612 Connector < 7.5 mm 3.0 mm 100 mm 112 mm (bottom view) 112 mm (components < 12.5 mm) 11 mm (connections < 2 mm) < 7.5 mm (side view) Figure 7: VC-20 Physical Dimensions ™ ATC-10b...
Need help?
Do you have a question about the VC-20-ATC-10B and is the answer not in the manual?
Questions and answers