COLOR MONITOR Chassis : KS6A(P) Model : SM0-210TPV SMO-150TPV COLOR MONITOR CONTENTS Precautions Specifications Alignment and Adjustments Troubleshooting Exploded Views and Parts List Electrical Parts List Block Diagrams PCB Diagram Wiring Diagram Schematic Diagrams...
Precautions 1. Precautions Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays. 1-1 Safety Precautions 1. Be sure that all of the built-in protective devices are replaced. Restore any missing (READING SHOULD protective shields.
Page 3
14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheat- ing, and correct any potential hazards. Samsung Electronics...
Page 4
Precautions 1-2 Servicing Precautions Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning2: An electrolytic capacitor installed with the wrong polarity might explode. 1.
Page 5
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Samsung Electronics...
Page 7
Specifications and IC Data 2-3 Semiconductor Basic Diagrams ELECTROLYTIC- CONDENSER DIODE LPM900W2(Pin 64) HCF4053(Pin 16) TRANSISTOR TRANSISTOR KSC5802 KSC815-Y KSA539-Y E B C TRANSISTOR LA7840 TDA6107Q KA7632 KSC2331-Y E C B Fig. 2-1 Semiconductor Base Diagrams Samsung Electronics...
3. Access the Adjustment Mode by pressing the “Volume-up”(video)keys. The adjustment 6. Cancel the Adjustment Mode by re-pressing parameters are listed in the accompanying the “FACTORY” or “Power SAVE” keys. table, and selected by pressing the left side two keys. Samsung Electronics...
Page 9
1. Press Remote control keys in the following sequence : “Menu” + “1” + “8” + “2” + “SET” 2. Press the Factory remote control keys in the following sequence : Menu Factory Item Initial Item Initial ADJUST OPTION G2-ADJUST RESET SCBT PSNS Samsung Electronics...
Page 10
0 ~ 23 19h(D5-D0) 1 0(Fix) Sub Sharpness gain adjustment 0 ~ 1 20h(D2) 1(Fix) NTSC Matrix : for japan Model PSNS 0 ~ 1 21h(D2) 1(Fix) Ident sensitivity PAL/NTSC decoder 3-3-3 WHITE BALANCE SECTION y(F/L) HIGH LIGHT LOW LIGHT Samsung Electronics...
Page 11
Adjust the Screen jack of FBT so that the value of SCREEN ADJUST can be shown as G2-ADJUST RESET ‘OK’. In this case, AV1 must be in NO Signal. 3-3-6 RESET The Reset Mode is used during User Menu Control Value inspection Function reset : ITEM Inital Value Contrast Brightness Color Samsung Electronics...
Page 12
But the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set has been moved or turned in a different direction, disconnect its AC power for at least 30 minutes. Samsung Electronics...
Page 13
11. Produce blue and red rasters by adjusting the low-light controls. Check for good purity in each field. 12. Tighten the deflection yoke. 4 Pole Magnet 2 Pole Magnet 6 Pole Magnet Clamper Screw Fig. 4-1 Convergence Magnet Assembly Samsung Electronics...
Page 14
2. Input a Toshiba pattern. (b) Low-Light Adjustment 1. Set SBT to 1.0 fL in the Factory Service Mode with using CA100. See Fig. 4-3. 2. Adjust RG,BG so that the levels are suitable to Fing. 4-3 each local area. Samsung Electronics...
Page 15
RED/BLUE GREEN BLUE BLUE RED/BLUE GREEN 6-Pole Magnet Movement 4-Pole Magnet Movement Fig. 4-4 Center Convergence Adjustment 3-4-9 Sub-Color Adjustment data to (Factory Mode). Samsung Electronics...
Page 16
Fig. 4-8 6. Adjust HS (Horizontal Shift) so that the left and right margins of the picture are 5. Fig. 4-6 4. Adjust with VSL (Vertical-Slope) so that the bottom margin of the picture is 4. Fig. 4-7 Samsung Electronics...
IC201S Abnormal Normal Replace Abnormal IC201S Check the FD801S, D813, IC801S Check the or AC-Fuse Check/Replace (33)Pin (H-Drive) IC804 of IC201S Abnormal Normal Abnormal Check the 125V- A Line Check the Normal FBT,P808 Check / Replace Q401 Samsung Electronics...
Page 19
Check IC201S D812,FBT Pin 51,52,53 (R.G.B) Normal Check IC201S Pin 42,43(Y,C) Check IC201S Pin50(IK) Abnormal Normal Abnormal Normal Check CNT02 Normal Check/Replace Check Pin 15,16(B+3.3V) Pin 11,12(B+5V) IC201S CRT and FBT Pin 6, 8(Y,C) Abnormal Check/Replace Mux b'd Samsung Electronics...
Page 20
Troubleshooting 4-3 No Sound(Video OK) Normal Check the signal output from CN601 Abnormal Check Speaker and Wire Normal Check IC601 Pin 1,2,3,4 Abnormal Check IC601 B + Line 13V Normal Check IC201 Pin 35 sound input Check/Replace IC201S Samsung Electronics...
200V TO CRT(VIDEO B+) CAM7 16.5V, -16.5V TO VERT.AMP, H.D.T DRIVE FUH-29A001B(S) CAM8 B+130V 6.3Vac TO CRT(HEATER) 3.3V TO VOC Voltage 5V TO EEPROM, EXPANDER IC AC INPUT STR-F6656 POWER TRANS Regulator 8V TO VOC KA7632 13V TO SOUND AMP Samsung Electronics...
Need help?
Do you have a question about the SM0-210TPV and is the answer not in the manual?
Questions and answers