Subscribe to Our Youtube Channel
Related Manuals for FWB interactiveRACQUETBALL
Summary of Contents for FWB interactiveRACQUETBALL
- Page 1 Installation Manual Fun With Balls GmbH Gyßlingstraße 72 80805 Munich Germany © 2020...
- Page 2 1. Hardware: With the following simple guidelines we would like to guide you to an easy installation of interactiveRACQUETBALL. Our system consists of one console, two sensor bars and four cameras. Fun With Balls GmbH, 2020 ©...
- Page 3 1. Hardware: Included hardware components of interactiveRACQUETBALL: Components: Console Sensor Bar Bottom Sensor Bar Top Camera Front Left Camera Front Right Camera Top Camera Rear Speakers Main Cable Fun With Balls GmbH, 2020 ©...
- Page 4 1. Hardware: Required court properties to install interactiveRACQUETBALL: Requirements: Dedicated Power Outlet Active Internet Connection Console Mounting Space Ceiling Load-Bearing 100kg/220lbs or Stand Load-Bearing 100kg/220lbs Floor and Ceiling Spaces to integrate the Sensor Bars Cable Ducts Wall Spaces for Cameras...
-
Page 5: Installation
2. Installation: First delivery: Second delivery: Console mounting plate Console Front Wall Paint Sensor Bars Cameras Main Cable The system will be installed and activated by our team or you will get remote installation support. Installation Steps: Check delivered components Check already sent components before for court preparation Check court measurements Check internet and power plug... - Page 6 2. 1. Check delivered components: Box 1: 1x Console 2x Speakers Box 2: 8x Sensor Bar Parts 4x Cameras 1x Wiring Harness Fun With Balls GmbH, 2020 ©...
- Page 7 2. 2. Check already mounted components before installation: The front wall should always be painted with our white paint. The console mounting plate (1) should already be fixed (load-bearing 100kg/220lbs) on the ceiling before starting installation. The console can also be placed on a stand (load-bearing 100kg/220lbs). Make sure that the console is placed in middle at the rear of the court at the most up position.
- Page 8 2. 2. Check already mounted components before installation: Cable channel (1) in the middle behind the front wall with a diameter of minimum 4 inch. Fun With Balls GmbH, 2020 ©...
- Page 9 2. 3. Check court measurements: With the help of a laser measurement device, check the front wall´s measurements. Front wall: Left side wall to right side wall inside length is minimum 239.85 inch. Optional the sensor bars can be cut by 0,75 inch for a wall inside length of minimum 239.1 inch. Sensor Bar Space Requirements Floor and Ceiling: Camera Space Requirements Front/Rear Wall and Ceiling: Fun With Balls GmbH, 2020 ©...
- Page 10 2. 4. Check Internet and Power Plug: Connect a laptop to the provided Ethernet connection with a cable. Open up a network browser window and go to website “speedof.me” to run an Internet Speed Test. Connect a device (Laptop charger, phone charger, etc.) to the provided power plug & check the device is charging. Fun With Balls GmbH, 2020 ©...
- Page 11 2. 5. Unpack & Arrange: Remove the nails that hold the box’s wooden walls together to bring the material out of its delivery box & bring them into the court. Arrange them to ease and make installation process fast. Fun With Balls GmbH, 2020 ©...
- Page 12 2. 6. Installation Console: Set anchor on the holding plate for the rope/chain hoist to lift up the console. Secure the chain hoist to the console metal structure. With the help of a scaffold, accompany the console as it’s being lifted up. Secure the console to the holding plate.
- Page 13 2. 6. Installation Console: Run the main cable (1) from the console (2) to the middle of the sensor bar bottom (3). Connect the console to power and internet (4). Fun With Balls GmbH, 2020 ©...
- Page 14 2. 6. Installation Console: Front light control: Place the switch (1) in the power supply system (2) of the court lights so that the front lights can be controlled by the console. Connect the female plug (3) with the power supply, the male plug (4) with the front light and connect the control cable (5) with the console. Fun With Balls GmbH, 2020 ©...
- Page 15 2. 6. Installation Console: Install the speakers (1) left and right next to the console with a distance of 19 inch. IW 406 FG II Installation Speaker: https://www.jamo.com/products/iw-406-fg-ii#manuals Connect the speakers (2) with the console. Fun With Balls GmbH, 2020 ©...
- Page 16 2. 7. Mount Sensor Bar Top: Start with sensor part number 1 from the left side. Remove the covers and mount the sensor bar flush into the ceiling directly in the connection to the front wall. Secure the green plugs (1) and run the cables through the cable duct behind the front wall to the sensor bar bottom. Mount the covers. Reference video links (interactiveSQUASH): ●...
- Page 17 2. 8. Mount Sensor Bar Bottom: Start with part no. 1 from the left side. Remove the covers and mount the sensor bar flush into the floor directly in the connection to the front wall. Reference video links (interactiveSQUASH): ● 10_Sensor tin bottom mounting ●...
- Page 18 2. 9. Connect Sensor Bars: Plug the red marked cables (1) coming from the sensor bar top into the SEA (2) port of the corresponding bottom sensor bar´s LVX (green board). Plug the black marked cables (3) coming from the sensor bar top into the EMA (4) port of the corresponding bottom sensor bar´s LVX . Fun With Balls GmbH, 2020 ©...
- Page 19 2. 9. Connect Sensor Bars: Connect the sensor bar parts with each other (1). Connect the the main cable (2) with the sensor bar bottom. Run the LAN cables (3) from the main cable (2) to the camera spots (4). Fun With Balls GmbH, 2020 ©...
- Page 20 2. 9. Connect Sensor Bars: When all tins are installed - Perform the calibration steps: Switch up the PIN 3 on all LVXs (green board) Unplug the power supply by disconnecting the main cable going in the y-splitter. Plug back in the power supply. Switch down the PIN 3 on all LVXs Unplug the power supply.
-
Page 21: Install Cameras
2. 10. Install cameras: Position front cameras. The camera housing measures 6.1 x 6.1 inch. The distance from the center (1) of the camera housing to the side walls is 31.5 and to the floor 9.22 inch. The distance from the outer edge (2) of the camera housing to the side walls is 28.44 and to the floor 6.17 inch. Reference video links (interactiveSQUASH): ●... - Page 22 2. 10. Install cameras: Middle position ceiling and rear camera. The distance from the front wall to the ceiling camera (1) is 234 inch. The distance from the the floor to the rear camera (2) is 86.5 inch. Fun With Balls GmbH, 2020 ©...
- Page 23 2. 10. Install cameras: Open the camera housing by removing the front glass. Mount the cameras flush into the walls and ceiling. Use the long holes (1) to fix the metal housing with screws. Bring the LAN cable through the hole (2), open the internal camera by 3 security screws (tool is in the boxes) and connect (3) the camera. Connect the LAN cables of the cameras with internet switch located in the console (4).
-
Page 24: Projector Adjustment
2. 11. Projector Adjustment: Using focus, adjust the projector's focus to the point that it's as sharp and accurate as it gets. Using Zoom and Shift, adjust the projection to cover the entire front wall. You’re now all set for the final installation stage of your interactiveSQUASH system. Once you’ve mounted all our hardware, our technical team is ready to support the setting of the hardware. - Page 25 2. 12. Hardware adjustments with setup: After all hardware mounting is done, your system will get set up for use. Our technical support will guide you on video / audio how to set all devices. Hardware adjustments include IR camera focus, IR lights setting. Checking the difference images &...
- Page 26 3. The Final Court: Now enjoy interactiveRACQUETBALL. Fun With Balls GmbH, 2020 ©...
Need help?
Do you have a question about the interactiveRACQUETBALL and is the answer not in the manual?
Questions and answers