Advertisement
Setting Preprogrammed Effects
• Light Type: Using the toggle switch, select the type of lights that
are attached to the PDS-60ca. See Fig. 5.
for iColor Flex SL, iColor Flex SLX, iColor Cove EC,
1
POSITION
iColor Cove QL or Pro products.
for iColor Tile FX.
2
POSITION
for future products.
3
POSITION
: Before engaging power, set the light type using the toggle
NOTE
switch. If Light Type is changed after power is engaged, the power
supply must be recycled in order to recognize the change.
• Mode: After selecting the light type, use the Mode button to select
the effect. Press and release the Mode button to cycle through each
effect. The following effects are available for each light type.
,
,
: Rainbow, Random, Color Wash, Fixed Color.
FLEX SL
COVE EC
PRO
: Burst, Spiral, Vertical Rainbow, Horizontal Rainbow, Random,
TILE FX
Color Wash, Fixed Color.
• Speed: Press and release to cycle through four speeds.
: When in Fixed Color mode, press and hold the Speed button
NOTE
to change colors.
• Option: The Options button lets you modify certain effects as
follows:
: Toggles between snap and fade changes.
RANDOM
: Each cycle increases through four width settings then
RAINBOW
reverses direction and decreases widths.
,
, and
: Reverses direction.
COLOR WASH
BURST
SPIRAL
: Once mode, speed, and options are set, PDS-60ca remem-
NOTE
bers your settings and recalls them after each power cycle.
Fig. 5
1 - FLEX SL, FLEX SLX,
COVE EC, COVE QL, PRO
2 - TILE FX
3 - FUTURE PRODUCTS
OPTIONS
SPEED
MODE
Sealing the Power Supply
• After all the power and data connections have been made, and all
through holes are water-tight, replace the cover and attach with pro-
vided screws. Tighten screws to 8 to 10 in/lbs.
: Before attaching cover, ensure gasket is seated properly and
NOTE
that no wires are pinched.
Replacing Fuses
: Ensure that the power supply is off before connecting or
WARNING
disconnecting fuses.
Each power output terminal of the PDS-60ca 7.5V and PDS-60ca 12V
is equipped with a fuse. Red LEDs are located next to each fuse to
indicate that power is present that the output connector. If an output
terminal is not functioning, replace the fuse as follows:
• Turn off power.
• Remove the fuse from the malfunctioning fuse terminal.
• Insert the replacement fuse into the fuse terminal. Use only correct
fuse size as noted on the fixture. See Fig. 6.
Fig. 6
Fuse
DMX/ETHERNET
PDS-60ca 7.5V
PDS-60ca 12V
PDS-60ca SPECIFICATIONS
Power Output 7.5VDC, 12VDC or 24VDC, 62W
Power Input
100-240VAC (auto ranging), 50-60 Hz; 1.7A
Ambient Temp 14˚F to 104˚F (-10˚C to 40˚C)
Packaging
NEMA 4 enclosure
Dimensions
8.27" (31 cm) X 5.36 " (14 cm) X 3.57" (9 cm)
Connectors
RJ45 data input and output connectors; 4-pin power
OUT
1
OUT 2
output connectors
Data Interface Color Kinetics Chromasic data interface output
DMX/ETHERNET
DMX
IN
OUT
WARRANTY
This product is sold pursuant to CK's Standard Terms and
Conditions (the "T&Cs") which may be found at
http://colorkinetics.com/howtobuy/buy/terms and which contain
important provisions, including, among others, Limited Warranty,
exclusions and limitations on CK's liability for damages, and restric-
tions on the remedies that are available to you.
OUT 1
OUT 2
DMX
IN
OUT
Advertisement
