Advertisement
Quick Links
Maintenance Instructions
ATTENTION!
Safe Operation & Maintenance Instructions must be followed.
In support of our policy of continuous product improvement we reserve the right to change materials and specifications without notice. Drawings, where used, are not to scale. All
dimensions are in millimetres and sizes given are approximate. Where possible, technical MSDS data sheets are made available on the website. All products should be installed and used
in accordance with manufacturer's instructions provided. Warning: products may be the subject of registered designs and patents. Refer to website for terms and conditions on warranty.
Safe Operation &
14.4V Cable Cutter
MSS-KREC-54AC
legendpower.com.au
legendpower.co.nz
Advertisement
Related Manuals for Legend MSS-KREC-54AC
Summary of Contents for Legend MSS-KREC-54AC
- Page 1 Safe Operation & Maintenance Instructions 14.4V Cable Cutter MSS-KREC-54AC ATTENTION! Safe Operation & Maintenance Instructions must be followed. In support of our policy of continuous product improvement we reserve the right to change materials and specifications without notice. Drawings, where used, are not to scale. All dimensions are in millimetres and sizes given are approximate.
-
Page 2: Safety Instruction
Thank you for using MSS products. This manual must be read Thank you for using KuDos® products. This manual must be read carefully prior to operating this product. Special attention should be paid carefully prior to operating this product. Special attention should be paid to the section “Safety Instructions”. -
Page 3: Table Of Contents
Contents 1. Safety Instruction ..................2. -
Page 4: Safety Instruction
Safety Instructions Work Area Safety Personal Safety 1. Keep the area around the tool 1. Stay alert while using this tool to clean and free of obstructions. prevent serious injury. Do not use under the influence of drugs, 2. Keep the area free of flammables alcohol or medicine. -
Page 5: Product Description
Product Description: MSS-KREC-54AC Specifications: Charger: Height: 338 (H)mm Input voltage: Weight: 3.4 kgs (including battery) 230V Single Phase AC Drive unit: 14.4V DC Motor Input frequency: 50-60Hz Charger (GS/CE): Input current: 21.75 VA Accessories: Plastic carrying case 2x 14.4V / 3.0Ah Li-ion Battery, 230V Charger Cutting Capacity: (Max. -
Page 6: Operate Instruction
Operating Instructions Operating Instructions 1. Install the charged battery by sliding it into the base of the tool handle until it clicks into place. The battery should be secured and unmoveable. 1. Install the charged battery by sliding it into the base of the tool handle until it clicks into place. - Page 7 3. Please find below diagram regarding on the safety switch. 3. Please find below diagram regarding on the safety switch. The safty switch need to be press in the same time when you press the The safty switch need to be press in the same time when you press the trigger to make the blade moving, once the blade move, then the finger trigger to make the blade moving, once the blade move, then the finger press on the safety switch can be remove.
-
Page 8: Battery Charging
Battery Charging 1. After removing the battery from the power tool, insert it into the battery Thank you for using KuDos® products. This manual must be read charger. The red indicator will light up and indicate the battery is charging. ... -
Page 9: Maintenance
would like to remind you to work safely and to keep this manual on hand. Inform Legend Power Systems authorized distributors in case of any abnormalities or Safety Instructions malfunctions of the product. DO NOT DISASSEMBLE OR ATTEMPT TO REPAIR THIS TOOL. -
Page 10: Trouble Shooting
Trouble - Shooting The Cable cannot be cut: A. Tool Blades are worn or damaged. The blades must be replaced. Tools with worn or damaged blades might cause property damage or even personal injuries. B. Applied cable is over-specification. Please check the specification table. The circuit breaker will need to be reset. -
Page 11: Warranty Information
Receipt and warranty card are required for warranty services. If the tool is found to be defective, in our sole judgement, Legend Power Systems will either repair or replace the defective product or part. In support of our policy of continuous product improvement we reserve the right to change materials and specifications without notice. Drawings, where used, are not to scale. - Page 12 Replace any worn or damaged parts immediately. - Contact Legend Power Systems ASAP to book in a repair/service Do NOT attempt to disassemble or repair the product. MSS hydraulic tools must be serviced by a qualified technician. Contact your Legend Power Systems representative for more information.
Need help?
Do you have a question about the MSS-KREC-54AC and is the answer not in the manual?
Questions and answers