Subscribe to Our Youtube Channel
Related Manuals for Ashland HDW-3217-12
Summary of Contents for Ashland HDW-3217-12
- Page 1 Parts Manual HDW-3217-12 WG-HDW3217-12 4/19 24916+ PH: 715-682-4622 www.ashlandind.com...
-
Page 2: Table Of Contents
Table of Contents Introduction Disc Harrow Specifications Frame Lift Cylinder Disc Gang Jack Oil Bath Bearing Wheel Carriage Assembly Decals Notations Operation & Maintenance Safety Guidelines Tire Inflation & Torque Chart Tire Service Hub Service Warranty Statement PH: 715-682-4622 www.ashlandind.com... -
Page 3: Introduction
Support section drop-down. If you have questions, please feel free to call or email us. You can visit us on-line at www.ashlandind.com. Ashland Industries hours of operation are 8:00 a.m. to 5:00 p.m. CST. We can be reached toll free at: 877-634-4622. -
Page 4: Disc Harrow Specifications
Disc Harrow Specifications Disc Diameter 32 Inches - Notched Disc Spacing 17 Inches Number of Discs 6 Front, 6 Rear Overall Dimensions: Length (Frame) 218 Inches Width 110 Inches Gang Diameter 2-1/2 Inches Weight 9,550 Pounds Width of Cut 91 Inches Depth of Cut 10-5/8 Inches Gang Angle (Adjustable):... -
Page 5: Frame
Frame Item Part Number Description 400428 Frame: Main Center, HDW 400429 Bearing: Articulation AFB-00187 HHCS: 1"-8 x 4" AFW-00001 Washer: 1" Flat AFW-00006 Washer: 1" Split Lock AFN-00012 Nut: 1"-8 Hex 400430 Frame: Wheel Carriage, HDW 400431 Support: Link Bar 400432 Bushing: 1-1/4"... - Page 6 Frame Item Part Number Description 400443 Pin: 7/8" x 3-1/4" 400445 Pivot: Offset Pole Bar 400446 Pin: 1-1/2" x 6-3/4" Main Pole Pivot 400447 Washer: 1-1/2" HT AFP-00015 Pin: 1/4" x 2-1/2" Cotter 400448 Stabilizer: Front Tower Bar 400449 Rod: Spring Control 400450 Pin: 1-1/16"...
- Page 7 Frame Item Part Number Description AFW-00040 Washer: 5/8" AFW-00031 Washer: 5/8" Split Lock AFN-00003 Nut: 5/8"-11 400469 Adapter: Hydraulic, Double Connection AFB-00094 HHCS: 3/8"-16 x 1" AFW-00010 Washer: 3/8" AFW-00028 Washer: 3/8" Split Lock AFN-00048 Nut: 3/8"-16 400470 Jack: Top Wind 400471 Pin: 3/4"...
-
Page 8: Lift Cylinder
Lift Cylinder - 400421 Item Part Number Description 400485 Barrel: 4" x 16" 400486 Rod: 2" 400487 Cap: Gland End 400488 Support: 2" x 4" Ring 400489 Seal: Piston Back-up Guide Ring 400490 Seal: 2" Rod Gasket 400491 Ring: 2" Wear Band 400492 Ring: 2"... -
Page 9: Disc Gang
Disc Gang Item Part Number Description 400658 Shaft: 2-1/2" x 97"L, w/o Nut 400413 Nut: 2-1/2" Hex HT 400412 Axle Washer: External, 2-1/2" 400426 Disc: 2-1/2" ID x 32" OD, 10-Notch, Cutting Blade 400418 Bearing: 2-1/2“ ID x 17"L Oil Bath w/ Wear Plate 400398 Spacer: 2-1/2“... -
Page 10: Jack
Jack Item Part Number Description 400470 Jack: Top Wind PH: 715-682-4622 www.ashlandind.com... -
Page 11: Oil Bath Bearing
Oil Bath Bearing – 400418 Item Part Number Description Oil: SAE 80W-90 Heavy Duty Gear Oil 400499 Housing: Oil Bath Bearing 400500 Bearing Ass'y.: Tapered Roller Cup/Cone 400501 Axle: Oil Bath Bearing 400502 Gasket: 0.01", 6-hole 400503 Gasket: 0.004", 6-hole 400504 Cap: Oil Bath Housing AFW-00030... -
Page 12: Wheel Carriage Assembly
Wheel Carriage Assembly – 601389 Item Part Number Description 504198 Spindle: 3-1/2” x 14-5/8” w/ Cross Hole A8020 Seal: Grease A9061 Bearing: Cone, Inner A8022 Bearing: Cup, Inner A125320 Stud: Wheel 5/8"-18 x 2-1/2" A125319 Hub: 8-hole A8024 Bearing: Cup, Outer A8025 Bearing: Cone, Outer A125321... -
Page 13: Decals
Decals Safety Decals Model Decals 750464 Decal: High Pressure ADS-00061 Decal: 25.75 x 5” ADS-00011 Decal: Pinch Point ADS-00062 Decal: 36 x 7” ADS-00019 Decal: Grease Daily ADS-00064 Decal: AI 5.5 x 3.5” ADS-00030 Decal: Turning ADS-00065 Decal: AI 11.5 x 7” ADS-00046 Decal: Do Lifting ADS-00085... -
Page 14: Notations
Notations PH: 715-682-4622 www.ashlandind.com... -
Page 15: Operation & Maintenance
Operation & Maintenance Your Ashland disc harrow is a durable piece of equipment and with proper care will yield many years of trouble-free operation. However, the life of your machine can be severely shortened by poor maintenance. You must follow consistent maintenance practices and use superior quality grease and hydraulic oil (compatible with the power unit’s hydraulic system) -
Page 16: Safety Guidelines
Safety Guidelines Safety Signal Words: Please note the use of signal words such as DANGER, WARNING, and CAUTION paired with the safety messages on your disc harrow. The appropriate signal word for each safety message has been selected using the following guidelines: •... -
Page 17: Tire Inflation & Torque Chart
Tire Inflation & Torque Chart On new machines, wheel nuts must be retorqued after the first 2 hours of operation. Check tires daily to ensure correct inflation levels with an accurate gauge having 6.9 kPa [(0.07 bar) 1 PSI] gradations. Tire: 295/75R22.5 MAX PSI: 96 Also check for: •... -
Page 18: Tire Service
Tire Service The task of servicing tires and wheels can be extremely dangerous and should be performed by trained personnel only, using the correct tools and following best- practice. Do not attempt to mount, demount, or inflate a tire if you do not have the proper equipment and experience to perform the job. -
Page 19: Hub Service
The bearings within the hubs of the disc harrow are fully greased with a Mobilith SHC™ 460 grease at the factory. Ashland uses a special bearing grease packer to ensure the bearing is effectively and evenly lubricated. Generous amounts of additional grease are added on both sides of the bearing prior to install within the hub. -
Page 20: Warranty Statement
This warranty is applicable only for the normal service life expectancy of the product or components, not to exceed one year from the date of delivery of the new Ashland Industries product to the original purchaser, or the date the product is first put into service via a rental agreement or other means, whichever occurs first. - Page 21 • Warranty Labor Reimbursement for labor expense to the dealer is made by payment of the established hourly shop rate. • Repair times will be reviewed by Ashland Industries and may be adjusted to average repair time required by other dealers to make similar repairs. Labor is not paid on the warranty associated with repair parts purchased by the retail customer that are used on a product that is not currently in warranty time frame.
- Page 22 30 day period. In these cases, the dealer must notify Ashland Industries in writing of the extenuating circumstance and advise that the continued use of the product will not enlarge the warranty claim.
- Page 23 30 days from the date of failure to Ashland Industries, Inc. routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid.
Need help?
Do you have a question about the HDW-3217-12 and is the answer not in the manual?
Questions and answers