Functions With Ptt Switch; Technical Characteristics - PRESIDENT ANDY II FCC Owner's Manual

When the color is set, long press the NB key (5) or the PTT switch
-
(11). A beep sounds, the characters of the color are displayed
during 1 second.
5) RESET
(EMG key)
- Turn on the power while pressing the EMG key (7) to reset to the
factory settings.
- "rS" blinks in the display.
- Press the NB key (5) for 1 second to confirm.
D) FUNCTIONS WITH PTT SWITCH
4 more functions are available. To activate the function press and
hold the PTT switch (11) and press the function key. Repeat this
process to deactivate the function.
1) TALKBACK
(PTT + NB key)
The TALKBACK function can be activated or deactivated as follows:
a) Press and hold the PTT switch (11)
b) Short press on NB key (5). Current TALKBACK level blinks 3 times
allowing you to adjust this level.
When function is activated, "TB" appears on the display.
This function allows to ear your own modulation with the CB speaker.
2) TALKBACK LEVEL
(PTT + s/t)
- At step b) adjust the TALKBACK level using the s/t keys (3).
When the function is on and "TB" is shown on the display, press
-
and hold the PTT switch (11), then use the s (3a) / t (3b) keys to
select the level. 9 levels from 01 to 09.
3) PA
(PTT + CB/WX key)
Press and hold the PTT switch (11)
-
- Short press on CB/WX key (6) to alternate between
(Public Address) mode. An external loud speaker can be con-
nected to your ANDY II FCC by the PA jack plug situated on the
back panel PA.SP (D). The CB message received or transmitted
into the microphone will be directed towards the external speaker
and be amplified. Adjust the PA volume with VOL key (1).
When PA mode is activated, "PA" and "AM" blink alternatively.
When PTT switch (11) is pressed, "PA" replace the active channel
on the display. Release the PTT switch (11) to display again the
active channel.
4) NOISE GATE
Press and hold the PTT switch (11).
-
- Short press the VOX key (8) to activate (On) or deactivate (OF)
the NOISE GATE. "
Noise Gate: Prevents amplification of background noise. This results
in optimized signal levels.
E) TECHNICAL CHARACTERISTICS
1) GENERAL
- Channels
- Modulation modes
- Frequency ranges
- Weather channels
- Antenna impedance
- Power supply
- Dimensions
- Weight
- Accessories supplied
- Filter
2) TRANSMISSION
- Frequency allowance
- Carrier power
- Transmission interference
- Audio response
CB and PA - Emitted power in the adj.
channel
- Microphone sensitivity
- Maximum drain
- Modul. signal distortion
11
(PTT + VOX)
" Is displayed when the function is active.
: 40
: AM
: from 26.965 MHz to 27.405 MHz
: 162.400 MHz to 162.550 MHz
: 50 ohms
: 13.8 V / 27.6 V
: 4.92 (W) x 7.09 (D) x 1.77 (H) inches
125 (W) x 180 (D) x 45 (H) mm
: ~ 1.98 lbs / 0.9 kg
: Electret microphone with support,
mounting cradle, screws.
: ANL (Automatic Noise Limiter) built-in
: +/- 200 Hz
: 4 W
: inferior to 4 nW (- 54 dBm)
: 300 Hz to 3 KHz
: inferior to 20 µW
: 7 mV
: 1.7 A at 13.8 V / 0.85 A at 27.6 V
: 2 %