Advertisement
DO NOT use sander with water, get the sander wet or use in damp or wet locations, the sander is for dry use only.
8
DO NOT operate sander if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT use where there are flammable liquids, solids or gases such as paint solvents or waste wiping or cleaning rags.
8
DO NOT leave the sander running unattended.
8
DO NOT carry the sander with your finger on the power switch.
8
When not in use disconnect from power supply and store in a safe, dry, childproof area.
9
LEAD pAINT WARNING!
Paint once contained lead as a traditional ingredient. The dust from the removal of such paint is toxic if inhaled or ingested and must,
therefore, be avoided. The following action must be taken before using the sander on a surface that you suspect may have contained
lead in the paint.
1.
User must determine potential hazard relating to age of paint to be removed. (Modern paints do not contain lead).
2.
DANGER! Keep all persons and pets away from the work area. The following are particularly vulnerable to the effects of lead paint dust:
Expectant women, babies and children.
3.
We recommend personal protection by using the following safety items:
a) Paint Spray Respirator (Sealey ref: SSP1699)
b) PE Coated Hooded Coverall (Sealey ref: SSP266)
c) Latex Gloves (Sealey ref: SSP24)
4.
Take adequate measures to contain the paint dust, flakes, and scrapings.
5.
Continue to wear safety equipment as in 3 above, and thoroughly clean all areas when task is complete. Ensure that paint waste is
disposed of, in sealed bags or containers, according to local authority regulations.
2.
INTRODucTION
9mm orbit designed specifically for use on car body work repairs. Six stage variable control from 3200 - 7200rpm. Ergonomic rubberised gear head
casing for added comfort and grip during use. Fitted with 5m mains cable. Supplied with Ø150mm hook and loop backing pad, side handle spare
brushes and hex key.
3.
SpEcIFIcATION
Model No: ..................................................................... OS600
Pad Size: ....................................................................Ø150mm
Motor Power: ................................................................... 600W
Supply: ............................................................................. 230V
No Load Speed: ................................................ 3200-7200rpm
Orbit Size: ..........................................................................9mm
Weight: .............................................................................2.5kg
Noise power/Noise pressure: ................................. 95/84dB(A)
Vibration: .......................................................................1.1m/s²
Uncertainty: ...................................................................1.5m/s²
4. ASSEMBLY
4.1.
FIT BAcKING pAD
WARNING! Remove from mains supply before performing maintenance or assembly.
‰
4.1.1.
Place tool on its back with spindle facing upwards. Place the backing pad on the spindle, ensure the spindle engages with
the hex recess on the backing pad.
4.1.2.
Lock the backing pad onto the spindle with the hex screw
supplied with the tool, using the hex key supplied.
WARNING! Before use, ensure that you have read and
‰
understood Section 1 Safety Instructions.
4.2.
Attach the side handle by screwing into which side
location is required.
4.3.
Attach the correctly rated sanding disc (not supplied) to
the sanding pad.
4.4.
Plug the sander into the electric power supply.
4.5.
Grip the side handle and turn on by pressing the trigger.
4.6.
The speed of the sander can be adjusted using the speed
control within the trigger, turn the control clockwise to
increase the speed or anti-clockwise to reduce the speed.
4.7.
Check that the unit is working correctly before use.
NOTE: The sander is designed for dry use only. DO NOT
use with water or any other liquids.
5. MAINTENANcE
WARNING! Disconnect sander from power supply before changing accessories, servicing or performing maintenance. Replace
‰
or repair any damaged parts. Use genuine parts only, unauthorised parts may be dangerous and will invalidate the warranty.
5.1.
After each 50 hours use (or as required), remove dust by blowing air through the side vents and around the pad bearing. Regular
cleaning will prolong the life of the sander.
5.2.
Only use mild soap with a damp cloth to clean the tool. DO NOT use cleaning agents containing solvents.
5.3.
Change pads when required. Ensure pad and disc RPM ratings are equal to, or exceed the machine rating. If the disc becomes
unbalanced, it will cause the bearings to wear.
5.4.
All other service and maintenance be carried out by an authorised Sealey stockist.
5.5.
When not in use store in a safe, dry, childproof location.
© Jack Sealey Limited
Original Language Version
OS600
Issue:1 - 03/05/19
Advertisement
