Toro 07344 Operator's Manual

1/3 platform lift for workman heavy-duty utility vehicle

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Form No. 3361-472 Rev A

1/3 Platform Lift

for Workman Heavy-Duty Utility Vehicle

Model No. 07344—Serial No. 2900000001 and Up

To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.

Original Instructions (EN)

Table of Contents

Summary of Contents for Toro 07344

Page 1 Form No. 3361-472 Rev A 1/3 Platform Lift for Workman Heavy-Duty Utility Vehicle Model No. 07344—Serial No. 2900000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com. Original Instructions (EN)
Page 2: Table Of Contents
3 Install the Main Wire Harness w/Relays....7 additional information, contact an Authorized Service 4 Mount the Parking Brake Switch......8 Dealer or Toro Customer Service and have the model 5 Mount Rear Level Switch ........9 and serial numbers of your product ready.
Page 3: Safety
Such • Do not use platform lift during lightning, use could void the product warranty of The Toro® thunderstorms, or high winds. Company. • Never move vehicle while platform is raised.
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-3701 93-3702 93-3710 93-3703 93-3711...
Page 5 93-3706 93-3704 93-3709 93-3708 93-3705 93-3707...
Page 6: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Remove the seat, shroud and fender – No parts required assemblies – No parts required Remove the hood Main Wire Harness w/ Relays Cable Tie Screw, 1/4 x 3/4 inch Install main wire harness w/relays...
Page 7: Remove The Seat, Shroud And Fender Assemblies
Remove the Seat, Shroud and Fender Assemblies No Parts Required Procedure 1. Position vehicle on a clean, level surface, stop engine, engage parking brake and remove key from ignition switch. Disconnect positive cable from battery. Figure 3 2. Unscrew and remove all knobs from console levers and from the gear shift lever (Figure 2).
Page 8: Install The Main Wire Harness W/Relays
2. Locate an empty slot in the fuse block. If no empty wire harness. Secure harness to vehicle wire harness slot is available, an additional fuse block (Toro part with (2) cable ties. no. 92–2641) will have to be added.
Page 9: Mount The Parking Brake Switch
loosely mount the level switch bracket to rear axle with locknuts removed. Mount the Parking Brake Switch Parts needed for this procedure: Parking brake switch Screws Procedure 1. Mount the parking brake switch to the parking brake Figure 6 mount with two screws as shown in Figure 5. 1.
Page 10: Mount Lift Onto Vehicle Frame
Figure 8 1. Hitch frame extension tube Figure 7 2. Locate and remove the threaded insert from the 1. Hitch plate mounting hole in left and right vehicle frame 3. Switch harness 2. Level switch bracket channels, as shown in Figure 9. 2.
Page 11 2. Locate and remove the threaded insert from the mounting hole in left and right vehicle frame channels, as shown in Figure 9. Figure 12 1. Vehicle frame channel 2. Threaded insert 3. Position a spacer tube onto each frame channel Figure 10 aligning mounting holes with holes in frame 1.
Page 12: Connect Wires
inch flange head capscrews and flange nuts. Use the 2. Reinstall shroud, seats, seat frame and console cover (2) 3/8-16 x 3 inch flange head capscrews in front plate, if applicable. mounting holes (Figure 13). 3. Reinstall overflow tube to radiator. Check coolant level and replenish, if required.
Page 13: Install Decals
Install Decals Parts needed for this procedure: Operation Decal G01021 1 No Step Decal Figure 17 1. No—Step decal For Workman 3000–4000 series vehicles with serial numbers 240000001 and up 1. Affix operation decal to top of console cover positioning as shown in Figure 15. 2.
Page 14: Product Overview
Product Overview Controls Up Button Press "UP" button to raise lift (Figure 18). Down Button Press "DOWN" button to lower lift (Figure 18). Key Switch Figure 19 Rotate key switch to authorize use of lift. Remove key 1. Emergency lowering valve knob from lift pendant control switch to prevent operation when unattended.
Page 15: Operation
Check Tire Pressure Operation Check tire pressure every 8 hours or daily to assure Check Oil Level proper levels. Refer to the vehicle operator’s manual for proper tire The lift reservoir is filled at the factory with DTE 13 inflation specification. hydraulic oil.
Page 16: Operating The Lift
7. Rotate safety blocks 90 degrees in channel and secure to ends of lift frame with retaining pins (Figure 22). Improper operation of platform lift may cause serious personal injury or death. To reduce risk to operator and bystanders: • Read and understand all safety instructions in Workman and Platform Lift Operator’s Manuals and warning labels.
Page 17 Operation of platform lift without parking brake Contact between non-insulated platform lift engaged can result in tip-over and personal and power lines will cause electrocution. injury. • Electrocution will cause serious personal • Always apply parking brake before operating injury or death. platform lift.
Page 18: Operating Tips
Contact with moving scissor arms can cause Falling or jumping from raised platform will personal injury. cause personal injury. • Stand clear of scissor arms while platform • Secure both handrail snap chains across is moving. opening before raising platform. •...
Page 19 Tip-over of Workman Vehicle while platform is raised will result in personal injury to operator and/or bystanders. • Always park vehicle on firm, level surface before raising platform. • Never exceed 5 degree maximum angle of operation. • Never raise platform if bubble level indicator is outside recommended operating range.
Page 20: Maintenance
Maintenance Battery Care 1. Battery electrolyte level must be properly maintained Check Safety Circuits and the top of the battery kept clean. If the machine is stored in a location where temperatures are The electrical safety circuits of the lift require the vehicle extremely high, the battery will run down more to be parked on a slope of less than 5 degrees, parking rapidly than if the machine is stored in a location...
Page 21 Warning CALIFORNIA Proposition 65 Warning Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. Charging the battery produces gasses that can explode.
Page 22: Schematics
Schematics Electrical Schematic (Rev. B)
Page 23 Notes:...
Page 24 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisﬁ ed with your Distributor’s service or have difﬁ...