Bivocom TG452 Series User Manual
  1. Manuals
  2. Brands
  3. Bivocom Manuals
  4. Gateway
  5. TG452 Series
  6. User manual

Bivocom TG452 Series User Manual

Industrial cellular edge gateway
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
®
Industrial Cellular Edge Gateway
TG452 Series User Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TG452 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Bivocom TG452 Series

Summary of Contents for Bivocom TG452 Series

  • Page 1 ® Industrial Cellular Edge Gateway TG452 Series User Guide...

  • Page 2: Copyright

    Product specifications and information in this document are subject to change without any notice, and BIVOCOM reserves the right to improve and change this user guide at any time. Users should take full responsibility for their application of products, and Xiamen Bivocom Technologies Co., Ltd.

  • Page 3: About This Guide

    About This Guide Thank you for choosing Bivocom Industrial Cellular Edge Gateway TG452 Series. Please thoroughly read this user guide before you configure and install the device. This manual is compatible with below models Model Description TG452-LF Industrial Edge Gateway with 4G/LTE Cat 4 Cat 6...

  • Page 4: Table Of Contents

    Table of Contents Copyright ..........................2 Trademark ..........................2 Disclaimer ..........................2 About This Guide ........................3 Table of Contents........................4 1. Introduction ..........................6 1.1 Overview ........................... 6 1.2 Applications ........................6 1.3 Dimensions ........................7 1.4 Physical Characteristics ....................7 2.
  • Page 5 3.4.4 IPSec ........................32 3.5 Advanced ........................33 3.5.1 Static Routing ...................... 33 3.5.2 Net Flow ....................... 34 3.5.3 GPS Location ...................... 34 3.5.4 DHCP and DNS ....................35 3.6 Data Collect ........................35 3.6.1 Basic Setting ....................... 35 3.6.2 Interface Setting ....................36 3.6.3 Modbus Rules Setting ..................

  • Page 6: Introduction

    1G flash and 32G micro SD local data storage, enables users to collect, store and process data at IoT edge network. 1.2 Applications TG452 Series Edge Gateways utilizes cellular network to connect your edge devices and controller devices to your center for remote monitoring and control. Typical application as below.

  • Page 7: Dimensions

    2.1 Package Checklist The following components are included in your TG452 package. Check the list before installation. If you find anything missing, Please feel free to contact Bivocom. 1 x TG452 Gateway 1 x Power Adapter (DC 12V/1.5A, EU/US/UK/AU plug optio)

  • Page 8: Installation

    2.2 Installation Hardware interfaces instruction: 2.2.1 SIM/UIM Card TG452 supports normal SIM/UIM only, so if you’re using a Micro SIM or Nano SIM card, you may need to use a Micro SIM or Nano SIM to Normal SIM adapter. Make sure your router is powered off, then use a needle object(such as a pen) to push the button near the SIM/UIM card holder, it will flick out immediately.
  • Page 9 ends of female connector and stripping cable, the signal of console cable is defined as below, RS232 Cable(with DB9 female connector and stripping cable) Color of cable Corresponding DB9-Female Pin No. Corresponding Pin No. of Router (Pin 1 closes to power jack, Pin 5 closes to ethernet port) Blue 1(TX)

  • Page 10: Power Supply

    2.2.3 Power Supply We suggest you use Bivocom standard power adapter (1.5A/12VDC). If you have to use your own power supply, make sure the power range is 5-35VDC and it is stable enough(Ripple shall be less than 300mV, and Instantaneous voltage shall not larger than 35V), meanwhile, power shall over 4W.

  • Page 11: Configuration And Management

    Use an Ethernet cable to connect the LAN port of TG452 to your laptop, or use your laptop or mobile phone to connect to WIFI hotspot ‘Bivocom’ of TG452, login with password: admin123, normally your laptop will get an IP address from TG452 DHCP as 192.168.1.xx, otherwise please manually configure your laptop IP to 192.168.1.100.

  • Page 12: View

    3.1 View To check the following system information. 3.1.1 System Display system related information.

  • Page 13: Network

    3.1.2 Network Display WAN, LAN, WiFi, DHCP network information.

  • Page 14: Routing Tables

    3.1.3 Routing Tables Display routing tables. 3.1.4 System Log Display system log.

  • Page 15: Vpn Status

    3.1.5 VPN Status Display VPN status. 3.2 Setup Main menu of this page includes, WAN, LAN, Wireless, Online Detection, Diagnostics. 3.2.1 WAN WAN supports DHCP/Static IP/PPPoE/3G/LTE connection mode. Choose the mode you need, then click ‘Switch Connection Mode’ and configure the related parameters, then you can connect to the internet.
  • Page 16 1) Server Type Type of network, the default value is AUTO, you can keep it or choose your own preference. 2) APN Different carrier might have different APN, please ask your carrier if you have no idea of what your APN is. 3) PIN PIN code of SIM card, please use it carefully, or the SIM card may be locked.

  • Page 17: Lan

    3.2.2 LAN Menu of LAN are mainly for configuring IP address of router, enabling DHCP server, and assign the IP address. The meaning of the parameters are as follows. 1) IPv4 Address To configure IP address of LAN port. 2) IPv4 Netmask The netmask of LAN port IP address.

  • Page 18: Wireless (Option)

    Lease time Time of assigning the IP address. 3.2.3 Wireless (Option) Menu of wireless are mainly for configuring the SSID, work mode, password, etc. Note, WiFi is not be included in standard TG452, please ask Bivocom representative when place the order.
  • Page 19 1) WIFI 2.4G Click ‘Enable’, to enable the WIFI function. 2) Network Name（SSID） WIFI network name. 3) Channel Support 1-13 channels, default value is auto, channel can be changed automatically. 4) Mode Support 802.11b, 802.11g, 802.11bgn. 802.11b up to 11Mbps, 802.11g up to 54Mbps and 802.11n up to 300Mbps. 5) Encryption You can only choose below types if the mode is set as 802.11b or 802.11g.

  • Page 20: Online Detection

    6) Key Password of sharing the WIFI, user need to enter it to access the internet. The minimum length of password is 8 bytes. 7) Hide SSID When Hide SSID enabled, SSID is invisible, and user need to enter the SSID to share the WIFI.
  • Page 21 1) Detection Type There are 3 types: ping, traceroute and DNS.  Ping Router will ping an IP address or DNS, if works, that means router is online.  Traceroute Traceroute will trace routing path, if achieves the target address, that means router is online. ...

  • Page 22: Diagnostics

    3.2.5 Diagnostics There are 3 types of diagnostics: ping, traceroute and nslookup Parameter of ping and traceroute can be a Domain Name or an IP address, used for checking if router is online or not. While nslookup is to analytic domain. 1) Ping Click ping, then you can check if there is response from an IP address, as bellow.

  • Page 23: Security

    3) Nslookup Click nslookup, then you can see similar reponse as below. 3.3 Security Menu of Security are for configuring the firewall, to ensure the security of accessing to internet, and implement the port forwarding, access control, data packet filtering, and other functions.

  • Page 24: Port Forwarding

    2) DMZ Host An IP address of a host of LAN you want to map. 3.2.2 Port Forwarding Comparing with DMZ, Port Forwarding is for more precise control, user can forward the data packet of a port to a host of LAN, to forward different port to different host. 1) Name You can name the rule you created.
  • Page 25 3) External Port Choose the port you want to open. In addition, traffic rule can be used for creating some access control rules, it can be from LAN to WAN, or WAN to LAN. 1) Name You can name the rule yourself. 2) Source Zone You can choose where to start the data packet.

  • Page 26: Custom Settings

    1) Restrict to Address Family You can choose IPv4, IPv6, or Pv4/IPv6. 2) Protocol To choose the protocol you want for access control, it can TCP, UDP or TCP/UDP. 3) Source MAC Address To choose the source MAC address of data packet. 4) Source Address To choose the source IP address of data packet.

  • Page 27: Pptp

    3.4.1 PPTP You can configure either PPTP client or PPTP server, but not both of them at the same time, as that may cause uncertain issues. 1) PPTP Client 1. PPTP Client You can enable or disable PPTP client. 2. Server Address To enter the IP address or Domain Name of PPTP server.
  • Page 28 Click Default Gateway, then a default route will be established under ppp0, and all the data will go through this route. 2) PPTP Server 1. PPTP Server You can enable or disable PPTP server. 2. Server Local IP To enter the server local IP address. 3.

  • Page 29: L2Tp

    3.4.2 L2TP You can also configure either L2TP client or L2TP server, but not both of them at the same time, as that may cause uncertain issues. 1) L2TP Client 1. L2TP Client You can enable or disable L2TP client. 2.
  • Page 30 2) L2TP Server 1. L2TP Server You can enable or disable L2TP server. 2. Server Local IP To enter the server local IP address. 3. IP Address Range Type the range of assigned IP address. 4. Enable MPPE Encryption. You can enable MPPE encryption here. 5.

  • Page 31: Openvpn

    3.4.3 OpenVPN 1) OpenVPN You can enable or disable OpenVPN. 2) Topology Choose the topology, it can be point to point or subnet Note: For point to point, a tunnel will be established between 2 devices. While for subnet, multi devices will be connected to one server. 3) Role When topology is subnet, you need to choose you want it be a server or client.

  • Page 32: Ipsec

    7) OpenVPN Server When you choose server in 角色, you need to enter an IP address or domain name of server. 8) Authentication Type If topology is subnet, authentication type is certification. If it is point to point, you can choose none, certificate or static secret.

  • Page 33: Advanced

    1) Peer Address To enter peer IP address or Domain Name, if choose as a server, you don’t need to enter 2) Negotiation Method You can choose ‘Main’ or ‘Aggressive’. 3) Tunnel Type You can choose ‘Site to Site, ‘Site to Host’, ‘Host to Host’, ‘Host to Site’. 4) Local Subnet Local subnet and mask, like 192.168.10.0/24.

  • Page 34: Net Flow

    Interface: To choose which interface you want to add routing. Target: Can be a host IP, or subnet. IPv4 Netmask: The netmask of subnet, if the target is host, the netmask shall be 255.255.255.255. IPv4 Gateway: The address of next-hop gateway address. Note: this address shall be achievable, or you’ll fail to add static routing.

  • Page 35: Dhcp And Dns

    Server Address: The IP address of server that you want the router to report the location, which is based on TCP connection. Server Port: The port of server. Report Interval: The interval time for auto report of router location, default value is 60 seconds.

  • Page 36: Interface Setting

    1) Data Collect: Enable or Disable data collect feature. 2) Collect Period: Set the period of data acquire from slave devices. 3) Report Period: Set the Period of data report to server. 4) Enable Cache: Enable or Disable history data cache feature. 5) Related data cache setting if enable the cache feature.

  • Page 37: Modbus Rules Setting

    3.6.3 Modbus Rules Setting Modbus Rules Setting is for TG452 as a Modbus master to acquire data from slave devices base on Modbus protocol. You can configure unlimited Modbus rules on it. TG452 provide the options of definable factor name, device ID, function code, register address and count register number, please following the slave device datasheet to get those information.

  • Page 38: Io Setting

    3.6.4 IO Setting IO Setting menu is for setting ADC ports, DI ports, and Relay ports. 1) ADC ports setting...
  • Page 39 2) DI ports setting...
  • Page 40 3) Relay Setting...

  • Page 41: Server Setting

    3.6.5 Server Setting Server setting menu allows user set the data center address with multiple protocols, the standard TG452 support TCP, UDP, HTTP, MQTT, and Modbus TCP. For the data format, TG452 support different Encapsulation type, include “Transparent”, “Json”, and “HJ212” (special for some Environment SCADA).

  • Page 42: Administrate

    3.7 Administrate 3.7.1 System 1) Host Name The host name of router, default name is router. 2) Time Zone Set up the time zone of system, default time zone is GMT8. 3) Language Change the language of configuration interface, default language is English. 4) Enable Telnet Access To enable the telnet server, the default function is enable.

  • Page 43: Time Setting

    1) Origin Password You’ll be required to enter your origin password before your revise your new password. 2) Password Type the new password you want to change. 3) Confirmation Type the new password again to confirm it. If the new password and confirmation password you type is different, then it fails to revise the password.

  • Page 44: Log Settings

    1) Current System Time Display the time of router. 2) System Time Type It includes NTP and RTC mentioned above, and different type has different configuration parameters  You can update data and time yourself. RTC Data Format must be: 20xx-xx-xx (Year-Month-Day), or you will fail to update it. RTC Time Format must be xx: xx: xx (Hour-Min-Second), or you will fail to update it.

  • Page 45: Backup And Reset

    1) Output to Device You can output the log to serial port, or specified file path, or external storage device, and the default path is:/var/log/ 2) Log Size Set up the size of log, default value is 64KB. 3) Log Server Set up the IP address of log server.

  • Page 46: Firmware Upgrade

    1) Download Backup Click to generate a configuration file in format of “backup-router-2016-**-**.tar.gz”. 2) Reset to Default Click ‘Perform Reset’, and a pop-up confirmation box with ‘Really Reset All Changes’ will display, then click ‘OK’ to reset to factory defaults. 3) Restore Backup After reset to default, you can also upload the saved configuration file to router, to recover the previous configuration.

  • Page 47: Remote Management

    Click ‘proceed’ to start the firmware upgrade, or click ‘cancel’ to stop the firmware upgrade. 3.7.7 Remote Management Remote Management feature allows TG452 work with Bivocom Device Management Platform for remote management, like firmware upgrade, configuration change, etc. You can configure the IP address and port of remote DMP server, device number and...
  • Page 48 1) Remote Manage You can enable or disable this function to choose if you want to remote manage the router or not. 2) Server Address Type the specified login server address you want to remote mange the router, it can be either an IP address or Domain Name.

  • Page 49: Manual Reboot

    8) Remote Upgrade Click ‘Enable’ to enable remote firmware upgrade function. 9) Server Address Type the server IP address or Domain Name for remote upgrade. 10) Server Port Type the server port for remote upgrade. 11) Firmware Version Type the firmware version that you want to upgrade remotely. 3.7.8 Manual Reboot Click ‘Perform Reboot’, and a pop-up confirmation box with ‘Really Reboot’...

This manual is also suitable for:

Tg452-lfTg452-w

Table of Contents