Product specifications and information in this document are subject to change without any notice, and BIVOCOM reserves the right to improve and change this user guide at any time. Users should take full responsibility for their application of products, and Xiamen Bivocom Technologies Co., Ltd.
About This Guide Thank you for choosing Bivocom Industrial Cellular WIFI Gateway TG451 Series. Please thoroughly read this user guide before you configure and install the device. This manual is compatible with below models Model Description TG451-W Industrial WCDMA WIFI Gateway...
TG451 Series Gateway utilizes cellular network to connect your network devices and serial port devices to your center for remote monitoring and control. Typical application as below. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
790g (1.74lbs) 2. Getting Started 2.1 Package Checklist The following components are included in your TG451 package. Check the list before installation. If you find anything missing, Please feel free to contact Bivocom. TG451 Gateway Host Power Adapter(DC 12V/1.5A) ...
Gateway and make sure it’s tightly matched. Warning: Never install SIM/UIM card when Gateway is powered on. Figure 2: SIM Slot and Power Supply Interface Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
2.2.2 6-Pin Terminal Block and Console Cable TG451 supports RS232 and RS485 serial port, which can be used for firmware upgrade, system log checking, or acts as serial port of a DTU(Please refer to Bivocom TD210 Series DTU). TG451 is designed with industrial terminal block interface, and the cable in this package...
To detect status of peripherals 2.2.3 Power Supply We suggest you use Bivocom standard power adapter (1.5A/12VDC). If you have to use your own power supply, make sure the power range is 5-35VDC and it is stable enough(Ripple shall be less than 300mV, and Instantaneous voltage shall not larger than 35V).
WAN is connected WAN is not connected LAN1 Blink LAN1 works LAN2 Blink LAN2 works LAN3 Blink LAN3 works LAN4 Blink LAN4 works Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Use an Ethernet cable to connect the LAN port of TG451 to your laptop, or use your laptop or mobile phone to connect to WIFI hotspot ‘Bivocom’ of TG451, login with password: admin123, then configure you local IP to 192.168.1.100.
Page 13
Only for private network SIM card, if you’re using public network SIM card, just keep it as null. 5) PAP/CHAP Password Only for private network SIM card, if you’re using public network SIM card, just keep it as null. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
IP address. The meaning of the parameters are as follows. 1) IPv4 Address To configure IP address of LAN port. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Lease time Time of assigning the IP address. 3.1.3 Wireless Menu of wireless are mainly for configuring the SSID, work mode, password, etc. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Page 16
You can only choose below types if the mode is set as 802.11b or 802.11g. While if mode is set as 802.11bgn, you can only choose below types. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
There are 3 types: ping, traceroute and DNS. Ping Gateway will ping an IP address or DNS, if works, that means Gateway is online. Traceroute Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Parameter of ping and traceroute can be a Domain Name or an IP address, used for checking if Gateway is online or not. While Dnslookup is to analytic domain. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Page 19
2) Traceroute Click traceroute, then you can see similar reponse as below. 3) Nslookup Click nslookup, then you can see similar reponse as below. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
1) DMZ You can enable or disable the DMZ. 2) DMZ Host An IP address of a host of LAN you want to map. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Traffic rules is used for opening some Gateway ports, such as remote access the configuration page of Gateway, you can open port 80; for remote SSH connection, you can open port 22. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Page 22
3) Destination Zone You can choose where to forward the data packet. Click ‘Add and Edit’, then you can get more detailed matching condition. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Page 23
To choose the protocol you want for access control, it can TCP, UDP or TCP/UDP. 3) Source MAC Address To choose the source MAC address of data packet. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
When you add rules, please add them at the bottom of existing rules, and don’t delete them. 3.3 Management 3.3.1 System Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
To revise the password of Gateway. 1) Origin Password You’ll be required to input your origin password before your revise your new password. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
2) System Time Type It includes NTP and RTC mentioned above, and different type has different configuration parameters You can update data and time yourself. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
How long to sync the time with NTP server, default time is 600 seconds. 3.3.4 Log Settings Log settings is for configuring the output parameters of system log. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
3.3.5 Backup and Reset User can either backup the configuration of Gateway, or reset to factory defaults. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Before you upgrade the firmware for Gateway, make sure the firmware you’re planning to upload is correct. If errors occurs, use serial port and connect the Ethernet cable, upgrade the firmware through u-boot. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Page 30
Size The size of firmware. Proceed Click ‘proceed’ to start the firmware upgrade, or click ‘cancel’ to stop the firmware upgrade. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
3) Server Port The specified login server port. 4) Heartbeat Interval The heartbeat time interval (Unit: second) 5) Device Number Device ID of Gateway. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Page 32
10) Server Port Type the server port for remote upgrade. 11) Firmware Version Type the firmware version that you want to upgrade remotely. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
DDNS function, while allows you to register a domain to bundle with the IP address, in this case, no matter what the IP address changed, it will direct to your registered domain. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Oray service will help you to bundle your intranet IP address with domain, and used for intranet traversal. Click ‘Login Management’ to start configure. Click ‘Reset Configure’ to clear the previous configuration. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
If above-mentioned are configured, and Gateway will auto implement the related priority level. 3.4.4 Static Routing Static routing is used to add a routing table entry. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Server Address: The IP address of server that you want the Gateway to report the location, which is based on TCP connection. Server Port: The port of server. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Even if the Gateway is powered off, the traffic statistics will be saved, and when you power on the Gateway, the traffic will be counted based on your last time traffic. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
English and number input. 3.4.8 Serial Application The serial port will transfer the data to server, or server will transfer the data to serial port. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Page 39
TCP (DTU): Configured as TCP client, which can be connected to TCP server, specified device number and heartbeat interval is required. PURE UDP: Configured as pure UDP client. PURE TCP: Configured as pure TCP client. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
OpenVPN and IPSec is more complex, as they need complex certification management, meanwhile, they offer more secured encrypted data. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
You can enable MPPE encryption here. 8. Default Gateway Click Default Gateway, then a default route will be established under ppp0, and all the Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Page 42
To create an username and password under CHAP Secrets, format as below, Username<space>*<space>password<space>* For example, if you want to create a username: test, password: test, it is as below, Test * testing * Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
8. Default Gateway Click Default Gateway, then a default route will be established under ppp0, and all the data will go through this route. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Page 44
To create an username and password under CHAP Secrets, format as below, Username<space>*<space>password<space>* For example, if you want to create a username: test, password: test, it is as below, Test * test * Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
8) Authentication Type If topology is subnet, authentication type is certification. If it is point to point, you can choose none, certificate or static secret. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
To enter peer IP address or Domain Name, if choose as a server, you don’t need to enter 2) Negotiation Method You can choose ‘Main’ or ‘Aggressive’. 3) Tunnel Type Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
10) ESP Encryption Algorithm The encryption method of ESP. 3.6 View To check the following system information. 3.6.1 System To display system information. Add: Unit 704, No. A3 Buidling, Tel.: +86-592‐6211713 Software Park, Xiamen, China 361000 Fax: +86-592‐6211727 www.bivocom.com sales@bivocom.com...
Need help?
Do you have a question about the TG451-W and is the answer not in the manual?
Questions and answers