Advertisement
2. intRoduction
composite case with integral battery clamp storage and carry handle. suitable for starting vehicles with 4 / 6 / 8 cylinder(rs1B/rs102B/
rs103B) petrol or diesel engines up to 2ltr/3.5ltr/5ltr. front panel displays internal or external battery charge levels and includes an integral
led work light. Audible reverse polarity warning. mains charger with automatic power cut-off prevents damage to battery whilst charging.
inbuilt mosfet circuit protection. fitted with two 12V power sockets that will accept any 12V device with a vehicle accessory socket plug.
single 5V 2.4A usB output. supplied with mains charger.
3. specification
model no ..............................rs1B....................rs102B..................rs103B
cold cranking Amps...............200A.........................300A......................420A
Peak Amps..............................900A.......................1200A....................1900A
Voltage......................................12V...........................12V........................12V
Auxiliary output usB...........5V/2.4A.....................5V/2.4A................5V/2.4A
Auxiliary output......................2x12V........................2x12V...................2x12V
cable/clamp length ..................0.6m..........................0.6m.....................0.6m
Weight.....................................6.7Kg.........................7.8Kg.................12.3Kg
4. opeRation
4.1.
jump staRting
4.1.1.
ensure both the ignition of vehicle to be started and the jumpstarter main power switch is switched
made to the battery.
4.1.2.
connect the red (+) alligator clamp of the jumpstarter to the red (+) positive battery terminal of the
4.1.3.
connect the BlAcK(-) alligator clamp of the jumpstarter to a non-moving metal part of the engine or chassis (avoid connecting to fuel
lines).
4.1.4.
switch the Jump start main switch to on position. listen for audible beep indicating an accidental reversed polarity – the red led
light within the display will illuminate solidly, and a continuous audible tone will be heard. if beeping is heard, switch off main power
switch, disconnect then reconnect clamps in the above order ensuring polarity is correct.
4.1.5.
once Jump starter main power switch is on, leave for approximately 30 seconds.
do not crank the engine for any more than 5 seconds at a time.
8
4.1.6.
if the engine fails to start, wait for at least 2 minutes before trying again to avoid overloading the unit.
4.1.7.
once the engine is running, switch the Jumpstart power switch to the off position. disconnect the BlAcK(-) negative clamp from the
vehicle battery first, and return the cable to its storage position on the jumpstart unit.
4.1.8.
Disconnect the RED (+) Positive clamp last, and return the cable to its storage position on the
connect the Jumpstarter to the supplied 230V Ac charger and recharge the unit to maintain battery life.
4.2.
LED MULTI-FUCTION DISPLAY fig1/fig3.
the led Battery display on the front panel shows several important pieces of information:
4.2.1.
With Jump start main switch in on position, pressing display button will show internal Battery capacity. use this to check if recharging
is required.
4.2.2.
solid red led indicator light when recharging is underway (to see battery bars press display button -
seconds but red led light will stay lit).
4.2.3.
flashing red indicator light when unit is fully charged (a press of the display button will also illuminate
4.2.4.
Reverse Polarity – the red LED at the top of the display panel will solidly illuminate. Also a continuous alert tone will be heard.
reverse polarity testing is only available when the Jump start main power switch is in the on position. if an accidental reverse polarity
is made, the inbuilt mosfet protection system will prevent any damage to both the Jump start unit and the connected vehicle battery.
4.2.5.
low Voltage alert – When main Jump start switch is in the on position, a single beep will be heard every 25 seconds when recharging
is required together with the red led indicator at the top of the battery display flashing, or approximately 60% remaining charge.
When pressing the led display button during these alerts, the remaining bars will flash on the display.
© Jack sealey limited
fig.1
Original Language Version
off before any connections are
vehicle.
jumpstart unit. As soon as possible,
display will go out after a few
battery bar display).
rs1B, rs102B, rs103B | issue 1 16/01/18
fig.2
Advertisement
