Advertisement
RESETTING THE PROGRAMMER
Electronic equipment can in some circumstances be affected by electrical interference. If the
programmer's display becomes frozen or scrambled; or if you wish to revert back to the default time
settings please use the following procedure.
Lower the front flap of the unit. On the Heating channel press the
ADVANCE and SELECT buttons together then release the buttons and
the programmer will return to the preset factory settings.
The normal working position for the SET switch is in the PROG.RUN position. In order to remind the user
of this, the flap is unable to be closed with the switch in any other position.
The simple instructions below are designed to help with the programming of the unit. All the following
instructions require the front flap to be lowered. Please replace the flap when normal operation is
required.
SETTING DAY AND TIME OF DAY
Move the SET
Use PLUS and
switch to the CLOCK
MINUS buttons to
position.
adjust day
12:OO
MON
SETTING
DEFAULT TIME SETTINGS
The default factory settings
are shown, however if you
MON-FRI
wish to change these
proceed as instructed below.
SAT/SUN
SETTING THE ON AND OFF TIMES
Move SET switch to
Use PLUS
Central Heating
and MINUS
or Hot Water
buttons to
position
adjust day
programme on any other
Repeat this
Press
process for 2nd
day of the week use the
ENTER
PLUS and MINUS buttons to
and 3rd settings
select day and press COPY
Should you encounter any problems, please refer to the
Question and Answer section located on page 4.
Page 2
FRONT COVER
Use PLUS and
Return SET switch to
Press
MINUS buttons to
PROG.RUN position
ENTER
adjust time
1:45
TUE
PM
PM
SET
1st ON 1st OFF 2nd ON
2nd OFF
6:30
8:30
12:00
12:00
AM
AM
PM
PM
7:30
10:30
12:00
12:00
AM
AM
PM
PM
Use PLUS and
MINUS
Press
Press
buttons to adjust
ENTER
ENTER
the 1st ON time.
If you require this
Programme the
remaining days.
SUN
SETTING 1ST
ON
OFF
6:30
8:30
AM
AM
The SET slide switch must be in the PROG.RUN position for the following instructions.
The following actions work independently on either Hot Water or Central Heating.
ADVANCE
Press SELECT once.
BOOST
Programme goes from
AUTO to ALL DAY
SELECT
Channel will operate
from first ON until last
OFF period
10:00
SUN
ALL DAY
ON UNTIL
8:30
PM
Press BOOST button
once for 1 hour of
On the ChannelPlus display - Boost 1 is Hot water extension 1 or 2 hour and Boost 2 is Heating extension 1 or 2 hours
3rd ON
3rd OFF
4:30
10:30
PM
PM
HOLIDAY FUNCTION
5:00
11:00
PM
PM
Move SET switch to the
HOLIDAY position
Use the PLUS
and MINUS
buttons to adjust
the 1st OFF time.
Whilst the HOLIDAY FUNCTION is in operation the system will remain OFF, the display will show the
number of nights remaining. The HOLIDAY setting is an instant function and cannot be set in advance.
The HOLIDAY FUNCTION can be cancelled at any time by pressing any of the SELECT buttons. Normal
programme functions will resume at the first ON period after the pre-set number of nights has expired.
Return SET
switch to PROG.RUN
position.
Programming ON/OFF times
If a Heating or Hot water period is not required it can be cancelled by setting the ON and OFF
settings to the same time. Example ON 10:00am OFF 10:00am
Your programmer will prevent you from accidentally overlapping ON and OFF times.
Example: If the 2nd ON time is set at 12:00pm and then you try and set the 1st OFF at 12:30 pm the
OFF setting will 'bounce' by a 10 minute period until the 2nd ON time has been adjusted.
SPECIAL FEATURES
Press SELECT again.
Programme goes from
Programme goes from
ALL DAY to ON
Channel will be
continuously ON
10:00
SUN
AM
AM
AUTO
AUTO
ON UNTIL
ON UNTIL
ON
10:30
10:30
AM
AM
BOOST FUNCTION
-
1 or 2 hour temporary override
Press BOOST button
twice for 2 hours of
Hot Water or
Hot Water or
Central Heating
Central Heating
ADVANCE FUNCTION
-
Brings forward next on or off operation
To cancel the advance press the ADVANCE
Press ADVANCE button once
button again. This will return the unit to
to move to the next
its normal programme
ON/OFF time
-
Allows system to be programmed for up to 32 days
Use the PLUS button to enter the
required number of nights
(MAX OF 32 NIGHTS)
INFORMATION AND ADVICE
Press SELECT again.
Press SELECT again.
Programme goes from
ON to OFF
OFF to AUTO
Channel will be
Programmer will return
continuously OFF
to normal ON and OFF
times
10:00
10:00
SUN
SUN
AM
AM
AUTO
AUTO
AUTO
ON UNTIL
ON UNTIL
ON UNTIL
OFF
10:30
AM
10:30
10:30
AM
AM
At any time during a BOOST
10:00
SUN
AM
BOOST 1 2
period press BOOST again to
AUTO
AUTO
return to normal programming
ON UNTIL
ON UNTIL
11:30
11:30
AM
Return SET switch to the
08
PROG.RUN position
SETTING
AM
Page 3
Advertisement
