Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Lode Labtech EC-12 R-S
- Page 1 Service documentation Lode BV Zernikepark 16 NL 9747 AN Groningen The Netherlands t: +31 50 571 28 11 f: +31 50 571 67 46 @: ask@lode.nl www.lode.nl INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11...
-
Page 2: Table Of Contents
1 - List of symbols used 1 - List of symbols used 2 - Validity 2 - Validity 3 - Setup instructions Labtech EC-12 R-S 3 - Setup instructions Labtech EC-12 R-S 3.1 - Cable selection 3.2 - Software Setup 3.3 - Ergometer setup... -
Page 3: List Of Symbols Used
This interface form covers * All Corival ergometers starting with serialnumber 9609xx-20150001 If your treadmill or ergometer is not covered by this interface form please contact Lode service service@lode.nl INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11... -
Page 4: Setup Instructions Labtech Ec-12 R-S
The driver is located under the services tab of the Lode homepage. 3.2 - Software 3.2 - Software Setup Setup Turn on the PC and start the program. Select “Settings” icon as indicated in the picture. INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11 4/22... -
Page 5: Ergometer Setup
3.3 - Ergometer setup 3.3 - Ergometer setup The following protocol needs to be set in the Lode ergometer to communicate with the external equipment. Bicycle ergometer: Lode Protocol The next chapters describe the procedures to setup these protocols depending on the type of ergometer. -
Page 6: Setting Up The Hardware
4 - Setting up the hardware Setting up the hardware Lode ergometers have two ways of connecting external devices. The cable selection depends on the connection possibilities of the external device. The previous chapter tells you which cable you need. This can be a RS232 cable or a USB cable. -
Page 7: Connecting With The Usb Cable
If there is no other connection available you can also use a USB cable to connect. 1. You will need an USB A to B cable (Lode part no. 930916) to establish communication between the Lode ergometer and your stress system or ergospirometrysystem. -
Page 8: Treadmill Or Ergometer With 3.5" Touch Screen Unit
Swipe with your finger over the screen as indicated with the red arrow in the picture to go to the main menu. INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11 8/22... - Page 9 The menu "Service" is only intended for service purposes to be executed by factory trainend personel. Select "Terminal Settings" to change the communication protocol. INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11 9/22...
- Page 10 Select the Communication protocol as desribed in "Ergometer setup" chapter. Select "Default" for the baudrate. INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11 10/22...
- Page 11 Select "RS232" or "USB" depending in which cable you have connected to the Lode ergometer. Select the button with the house to go back to the main menu. INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11 11/22...
- Page 12 Select "Terminal" to set the ergometer in terminal mode. Your device is now ready for external control. INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11 12/22...
-
Page 13: Treadmill Or Ergometer With 7" Touch Screen Control Unit
*Note that for this instruction the graphic view for a Lode Corival is used. The view for a treadmill might difer a bit but the procedure is the same. INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11 13/22... - Page 14 "Terminal". Select the communication protocol ad described in the "Ergometer setup" chapter. Use the scroll button to view the complete list. INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11 14/22...
- Page 15 Select "Default" for the baudrate. Select "RS232"or "USB" depending on the type of cable that you connected to the Lode ergometer. INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11 15/22...
- Page 16 - Go to the settings menu - Select "Default Start Menu" - Select "Terminal" - Switch the ergometer off and on. It will boot directly into terminal mode. INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11 16/22...
-
Page 17: Nummerical Control Unit - Treadmill Only
7 - Nummerical Control Unit - Treadmill only 7 - Nummerical Control Unit - Treadmill only 1. Press and hold key #1 and #2 as shown on "Figure 1" for 10 seconds. INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11 17/22... - Page 18 3. By using the "+" and "-" keys for the grade adjustment #3 you can change the "0" behind terminal to "1" to activate the Terminal mode. 4. Press enter #4 and "prot id" will be shown on the display, for Lode protocol this should be set to "1". Set the protocol as described in the "Ergometer setup" chapter.
-
Page 19: Treadmill Or Bicycle Without Control Unit
Connect an USB cable from the computer to the USB port of the treadmill or use a RS232 cable from the computer to the RS232 port Start the Lode Service Manager and login with the same account details that you use to login on the website. - Page 20 6. Switch the device off, wait 10 seconds 7. Switch the device on The screen as shown left should show up within 5 seconds after powering up. INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11 20/22...
- Page 21 Lode ergometer. Select default for the baudrate. Note that Default should always be selected unless different specified by your dealer. INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11 21/22...
- Page 22 Your device is now ready for use with the external controller. Note that the device is automatically switched to terminal mode when no manual controller is present at the device itself. INTERFACE SHEET - LABTECH EC-12 R-S - CPET ERGOMETER / VERSION: 1.0 - 2016-01-11 22/22...