Advertisement
Quick Links
Trim Tab Installation with Electronic Sensors
Model Number: TTK1150EL, TTK1050EL, TTK950EL, TTK850EL, TTK750EL
Parts Included
(2) Trim Tabs with Sensors
(2) Hydraulic Pumps
(2) Mounting Templates
Harnesses - TTMWH & (2) - TTIWH
Mounting Hardware
Stainless steel hoses sold separately- 2 hoses required per tab
Mounting Tab Location
Available mounting area:
Before selecting a mounting location verify proper clearances inside (transom mounted compo-
nents, etc) and outside (turning drive and propeller clearance) of the boat. Do not mount tabs
in the chine area.
NOTE: The farther the tabs are between each other the better, this will allow you to achieve
the maximum performance out of your tabs.
LIT-TTEL-ML-INST
REV A
ECO 28610
715 Center Street
Grayslake IL 60030
P: 847-752-2700
F: 847-752-2415
www.livorsi.com
1 of 12
Advertisement
Related Manuals for Livorsi TTK1150EL
Summary of Contents for Livorsi TTK1150EL
- Page 1 Grayslake IL 60030 P: 847-752-2700 F: 847-752-2415 www.livorsi.com Trim Tab Installation with Electronic Sensors Model Number: TTK1150EL, TTK1050EL, TTK950EL, TTK850EL, TTK750EL Parts Included (2) Trim Tabs with Sensors (2) Hydraulic Pumps (2) Mounting Templates Harnesses - TTMWH & (2) - TTIWH...
- Page 2 Billet Trim Tab Installation Mounting tab location cont. Transition of the hull to tabs: Recommended Transtion: Allows tab to be removed fully from the water flow underneath the boat while under way. Some applications may require the tab to be mounted even higher to be out of the water flow. REV A 2 of 12 LIT-TTEL-ML-INST...
- Page 3 When printing make sure your print settings do not resize the document, keep it at 100% or disable any scale options. NOTE: PORT AND STARBOARD TEMPLATES ARE DIFFERENT Example of the Livorsi bolt pattern Port mount sensor wires Plug Thru hull bolts...
- Page 4 Billet Trim Tab Installation Mount the tab: If the Livorsi Trim Tabs are replacing existing tabs, make sure to seal any unnecessary holes on the transom. Use a high quality marine sealer suitable for underwater use. Recommended sealant: Marine Grade RTV / silicone sealant 4200 or 5200.
- Page 5 Billet Trim Tab Installation 12 VOLT 24 VOLT See page 7 for wiring diagram See page 6 for wiring diagram REV A 5 of 12 LIT-TTEL-ML-INST ECO 28610...
- Page 6 Billet Trim Tab Installation 24 VDC Trim Pump Wiring Diagram BLACK (-) GROUND (+) 24VDC BLUE/WHITE : UP GREEN/WHITE: DOWN BLACK: GROUND RED/WHITE: POWER ROCKER SWITCH Recommendation: Use Good Quality Metal Protectant or Dielectric Grease on All Wire Connections. FUSE BREAKER/FUSE MOTOR AMP MINIMUM...
- Page 7 Billet Trim Tab Installation 12 VDC Trim Pump Wiring Diagram BREAKER/FUSE AMP MINIMUM Recommendation: Use Good Quality Metal Protectant or Dielectric Grease on All Wire Connections. BREAKER/FUSE AMP MINIMUM REV A 7 of 12 LIT-TTEL-ML-INST ECO 28610...
- Page 8 Billet Trim Tab Installation Sensor Wiring The sensor wire leads that were fished thru the transom will need to be inserted in to the 6 pin Deutsch connector and secured with a wedge lock. Below is the pin out. Pin Number Wire Color Description PPS1 (5V)
- Page 9 Billet Trim Tab Installation Connections directly to LED Indicator REV A 9 of 12 LIT-TTEL-ML-INST ECO 28610...
- Page 10 Billet Trim Tab Installation Connections to a Mercury VesselView® REV A 10 of 12 LIT-TTEL-ML-INST ECO 28610...
- Page 11 Billet Trim Tab Installation Fill the pump with oil: The pump reservoir has markers indicating the maximum and minimum oil levels. The operating temperature and the oil used will determine the reaction speed of the tabs. Non-detergent oils recommended. Types of Oil Reaction Time FASTER 20w20...
- Page 12 Billet Trim Tab Installation Check all hydraulic fittings for leaks Trim Tab Maintenance Marine growth can interfere with proper operation of the trim tab planes and actuators. To reduce problems due to marine growth, always return the trim tabs to the full "UP" position after operating the boat and periodically inspect and clean marine growth from the actuators and planes.
- Page 13 1050 Trim Tab Angles - Pin location 1 For reference only 90° Transom Angle 7.500” (Clearance from 90°) 90° 90° 4” Pin location 1 5° Transom Angle 5.500” (Clearance from 90°) 5° 90° 5.875” Pin location 1 12° Transom Angle 3.250”...
- Page 14 1050 Trim Tab Angles - Pin location 2 For reference only 90° Transom Angle 9.625” (Clearance from 90°) 90° 90° 90° .625” Pin location 2 5° Transom Angle 7.750” (Clearance from 90°) 5° 90° 2.500” Pin location 2 12° Transom Angle 5.750”...
- Page 15 1050 Trim Tab Angles - Pin location 3 For reference only 90° Transom Angle 11” (Clearance from 90°) 90° -2.250” 90° Pin location 3 5° Transom Angle 9.250” (Clearance from 90°) 5° 90° .500” Pin location 3 12° Transom Angle 6.875”...
- Page 16 1050 Trim Tab Dimensions REV A ECO 28610 LIT-TTEL-ML-INST...