ICHRoboter iCleaner-200 User Manual
  1. Manuals
  2. Brands
  3. ICHRoboter Manuals
  4. Swimming Pool Cleaners
  5. iCleaner-200
  6. User manual

ICHRoboter iCleaner-200 User Manual

Hide thumbs

Advertisement

Table of Contents

200

Advertisement

Table of Contents
loading

Related Manuals for ICHRoboter iCleaner-200

Summary of Contents for ICHRoboter iCleaner-200

  • Page 2: Safety Warnings

    The iCleaner-200 is designed for use in swimming pools only. Any other use is prohibited and will void manufacturers' warranty. Do not swim in the pool whilst the iCleaner-200 is in use in order to avoid personal injury. Do not allow the Power Box to come in contact with water, and it is recommended to be placed in a shady, dry and ventilated area.

  • Page 3: Product Overview

    Remote Control. When the Remote Control is not being used, the iCleaner-200 will return to automatic mode. ◇ Overall cleaning: the iCleaner-200 not only cleans the floor of your pool, it also cleans the wall, at the same time, the iCleaner-200 will filter water, and the dirt will be collected into Filter Bag.
  • Page 4 2.3 Parts List Main Body Parts Guide Vane Water Joint Drive Belt water retaining board Base Plate Filter Net Base Plate Latch Support Frame Filter Bag Motor Box （Pic.2.3.2） - 3 -...
  • Page 5 ※ Power Box Parts - 4 -...

  • Page 6: Packing List

    3 Packing List Serial Quantity Remarks Part Name Number Unit Body Power Box Remote Control Battery Host Guide Vane User Manual Warranty Card Certificate of Quality Floating Cable Impeller Spare Parts Filter Bag （Pic.3.2.1） - 5 -...

  • Page 7: Power Connection

    4 Product Operation 4.1 Power Connection ※ Please connect the Floating Cable to the Cable Socket of Power Box (see Pic. 4.1.1), then connect the Power Box to an outside AC power of 100v/240v 50/60Hz (see Pic.4.1.2). For the complete connection guide please refer Pic.4.1.3 Notices: Do not allow the Power Box to come in contact with water.

  • Page 8: Start-Up Procedure

    4.2 Start Up Procedure (1) When placing the iCleaner- 200 in the pool: you must wobble the iCleaner-200 according Pic.4.2.1 to make sure the air inside is released when you put the iCleaner- 200 in the water, So it will automatically sink to the bottom of pool.
  • Page 9 Latch on the Base Plate (Pic4.3.2) and remove the Filter Bag from Base Plate, clean the Filter Bag (Pic.4.3.3), once clean place the Filter Bag on its frame, reassemble the Base Plate and put it back into the iCleaner-200 once the Filter Bag is dry.
  • Page 10 (3) iCleaner-200 Storage: When the iCleaner-200 is dry,disconnect the floating cable reel it in hand-over-hand and place on the iCleaner-200, then store the iCleaner-200 in a dry,well-ventilated area. If you have the Caddy , please put the iCleaner-200 & Floating Cable on to the Caddy Cart, details please refer Pic.4.3.4...
  • Page 11 4.5 Water Joint Step 1 ※ Insert water joint into Icleaner-200. (Pic.4.5.1) Step 2 ※ Screw down the Lock Nut clockwise. (Pic.4.5.2) （Pic.4.5.2） - 10 -...

  • Page 12: Maintenance

    ※ Change the Impeller if the old one gets worn or damage Guide Vane Step 1: ※ Rotate Guide Vane clockwise to remove from the iCleaner-200.(Pic.5.1.1) Step 2 ※Use a Phillips head screw driver to remove the bolt in the Impeller according the diagram.(Pic.5.1.2)
  • Page 13 5.2 Sponge Wheel Replace the Sponge Wheels if they are badly worn or broken Step 1 OPEN ※ Invert the iCleaner-200 on the floor, remove the OPEN Base Plate.(Push latch to u n l o c k t h e B a s e Plate).(Pic.5.2.1)
  • Page 14 Step 3 ※ Using a Phillips head screwdriver and 7mm ring spannerundo the six bolts and nuts on the Side Cover,to remove the Side Cover . ( Pic.5.2.3) Transmission Components Side cover （Pic.5.2.3） Step 4 Rolling Brush ※ Remove the Rolling Brush.
  • Page 15 Step 5 ※ Slide the old sponge wheels off, and replace w i t h n e w s p o n g e wheels(Pic.5.2.5) （Pic.5.2.5） Step 6 wheel axle ※Assemble the Rolling Brush to the axle (Pic.5.2.6) .
  • Page 16 Latch locks into the bracket.the filter until the Latch locks into the bracket (Pic.5.2.9) （Pic.5.2.9） Step 10 ※ Place the base Plate into iCleaner-200, pressing down until the latches lock into place. (Pic.5.2.10) ※ Replacing the Sponge Wheels is now completed （Pic.5.2.10）...

  • Page 17: Filter Bag

    5.3 Water Retaining Board Replace the Water Retaining Board if they are broken(Pic 5.3.1) hole Step 1 ※ Remove the base plate from the iCleaner and remove the filter bag, then open the water retaining board to the vertical position and carefully slide the water retainining board to one end, remove the water retainining board carefully.
  • Page 18 Note: The Power Box MUST BE DISCONNECTED from the power supply prior to conducting any maintenance on the iCleaner-200. Contact your local distributor, or place of purchase for problems not covered in Trouble Shooting Guide. - 17 -...
  • Page 19 Indicator Indicator Solution Solution Failure Failure light light 1.Check whether the impeller is damaged; The iCleaner Green light Green light 2.Check whether the water pump motor is working; has stopped Water Return the robot to deeper water and restart flashing flashing 3.Put the robot in the water.
  • Page 20 ◇Please inspect and clean the impeller & Guide Vane according to chapter 5.1, after use. ◇If you are not going to use the iCleaner-200 for an extended period of time, make sure iCleaner-200 & Power Box is turned off, and store it in a dry, shady &...

Table of Contents