Sharp LC-60UI9362K Quick Start Setup Manual page 2

Setting up the TV set for the fi rst time
What is included
1 Fitting the stand
in the box
TV panel must be facing downwards.
1 x Operating Instructions
Note: To complete the stand
1 x Quick Start Guide
installation you will require a
1 x TV cross head screw driver.
1 x Remote Control
2 x AAA Batteries
1 x Stand installation pack
RF Cable
1 x
4 x
Used for attaching the stand
to the TV set (fi g.2)
2 Connecting your set
Outdoor Digital
TV Aerial
1.
2.
1) Connect the TV to your power socket.
2) If you wish to use the TV to receive Freeview/Saorview channels, connect the RF input from
the TV to your outdoor Digital TV aerial. If you do not wish to receive Freeview/Saorview, skip
this step.
4 First time installation
Basic installation steps are shown below. These may vary slightly depending on model.
1
Introduction
When the set fi rst turns on, it enters the First Time Installation
mode. This can be restarted by restoring the set to default settings
in the 'About TV' Menu.
Note: In home mode,
the TV will switch off
automatically after 4
hours in the event that
no buttons are pressed on
the TV or remote control.
(You can change this
by pressing the [MENU]
button and then selecting
Settings>Time>Auto
4
Standby)
Environment of Use
Home Mode: For normal use, by default it is set to a power saving mode
which reduces the energy used by up to 25% (by reducing the power to
the LED/LCD panel). This can be changed in the picture mode settings.
7
Default Source
Select the source which you use the most. If Digital TV (Freeview) is chosen,
then at the next step, the set will tune in and default to Digital TV (Freeview).
If one of the other sources is selected, then the set will not tune in at this
stage and default to that input. If it is required to tune the set in later, press
the [MENU] button and then select Settings>Channels
L
R
2
1
Place the TV set on a fl at and clean surface
When the two feet are fi tted, they will appear
with the panel facing downwards to avoid
as in the picture above, with the tips of the feet
damage.
pointing away from each other.
3 Powering On the TV
TV Control Stick
Switch on the television by pressing the TV control stick
located on the TV set.
2
Languages
Select your preferred on-screen display language. This will change the language
in which the menus and associated information is displayed in. When set up has
been completed, to change this press the [MENU] button and then select Settings >
System Menu > Language
5
Network setup
You can connect the TV to your broadband router or wireless network in order
to take advantage of the Smart functions. If you connect the TV to your router
using an Ethernet cable (recommended) this step will be skipped.
8
Tune in Channels
Choose to install terrestrial channels now or later.
3
When the stand/feet are in the correct position,
secure the feet to the underside of the TV set
using 4 screws provided.
Remote Control:
Installing Batteries
TV control stick
Insert the batteries supplied into the remote control and
press the standby button to power on the TV.
3
Country Selection
Select the correct fl ag for the country in which the set will be
used in. This will enable the set to correctly install the functions
applicable in the country of use.
6
Set Up Netfl ix
If you have a Netfl ix account, it can be set up on the television
here. Once set up and validated, the First Time Installation
returns to the next step.
9
Support Advice
Information regarding support is displayed for a little while.
Tuning continues and a progress bar is shown with the number of
channels found indicated below.
If you are picking up signals from more than one transmitter, you
will be requested to select your primary and secondary regions.
Register your manufacturers
guarantee online within
4 x
14 days of purchase at
www.registertoday.co.uk/sharp
and enter into a prize draw to
win a Sharp Soundbar
Terms and conditions apply. Online registration only.
UK Only.
To receive Freeview channels, in particular
Freeview HD channels, you will need a
Digital TV aerial and be in a good Freeview
coverage area. You can check coverage for
your postcode at www.freeview.co.uk.
Please note that any Freeview HD channels
found during tuning will be placed in
channel positions above 100.
For example, 101 (BBC1 HD) 102 (BBC2 HD)
etc.
Connectivity
ETHERNET
5V 5V
500mA MAX 500mA MAX
A
USB 1 (2.0) USB 2 (2.0)
D
C
L R
DIGITAL
B
AUDIO OUT E
OPTICAL
A
Ethernet/LAN* Network connection
B
Digital Audio Digital Optical Audio Output
C
USB 1 USB port 2.0
D
USB 2 USB port 2.0
Audio shared for Video/Composite
E
L/R HDMI input
and component/ YPbPr
F
HDMI 1 HDMI input 2.0
G HDMI 2 HDMI input 2.0
Video Input (green) and HD input
H
Video/YPbPr
(Ypbpr)
* The Ethernet/LAN port is used for Freeview HD services and smart functions.
ROI Only.
To receive Saorview channels, in particular
Saorview HD channels, you will need a
Digital TV aerial and be in a good Saorview
coverage area. You can fi nd out more at
www.saorview.com.
P
O
N
M
L
K
1 (2.0) 2 (2.0)
J
F G
VIDEO/Y Pb Pr
I
H
I
SAT IN Satellite input
J
RF in RF / TV aerial input
K
HDMI 3 HDMI input 2.0 (ARC)
L
USB 3 USB port 2.0
M
CI card in Common interface module
N
SD SD card input
O
Earphones Earphone input
Input is used only by
P
Service Input
service centres