Fischer Connectors FO1 Assembly Instruction Manual
  1. Manuals
  2. Brands
  3. Fischer Connectors Manuals
  4. Cables and connectors
  5. FO1
  6. Assembly instruction manual

Fischer Connectors FO1 Assembly Instruction Manual

Fiberoptic series
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Assembly Instruction for FiberOptic Series
FO1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FO1 and is the answer not in the manual?

Questions and answers

Related Manuals for Fischer Connectors FO1

Summary of Contents for Fischer Connectors FO1

  • Page 1 Assembly Instruction for FiberOptic Series FO1...

  • Page 2: Table Of Contents

    FO1 R13 Receptacle with Wire Set ......................... 13 Terminus assembly ..............................15 Polishing .................................. 17 Appendix ................................25 This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.

  • Page 3: Introduction

    Fischer FiberOptic Fischer FiberOptic Series single channel - 1 fiber International Electrotechnical Commission This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.

  • Page 4: Fo1 Plugs & Receptacles With Cable Clamp Set

    Terminus "C" as shown on the picture. This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 5 Clamp Set Body “F”. Screw the Rear Nut "I". Recommended torque : 3.0 Nm This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 6 R01, R03 and R50 receptacles. Thus, this final assembly step is valid only for P01 plug. This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.

  • Page 7: Fo1 Plugs & Receptacles With Potting Set

    Polishing: See section 9 Insert the Terminus "C" into the Connector Body "B". This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 8 : -55°C to 110°C. This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 9 Bend Relief ”I” bottoms against the Back Nut “G”. This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 10 R01, R03 and R50 receptacles. Thus, this final assembly step is valid only for P01 plug. This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.

  • Page 11: Fo1 R01 & R03 Receptacles With Wire Set

    Crimping Sleeve ”C” and heat Shrink tube operating temperature range : -55°C to 110°C. This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 12 Screw the Wire Set Nut “F” on the Connector Body “A”. Recommended torque : 3.0 Nm This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.

  • Page 13: Fo1 R13 Receptacle With Wire Set

    Crimping Sleeve ”D” and heat it. Shrink tube operating temperature range : -55°C to 110°C. This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 14 Screw the Wire Set Nut “F” on the Connector Body “B”. Recommended torque : 3.0 Nm This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.

  • Page 15: Terminus Assembly

    Cure the epoxy 120 +10/- 20[°C] during 20min. Cleave fiber Scribe Tool This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 16 Position the Housing O-ring “A” on the Termini Housing “B” as shown on the left picture. This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.

  • Page 17: Polishing

    Spray abundantly demineralized water on the polishing film. This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 18 (or pattern of the  Lubricant: DI- polishing machine). water Fixture tool: FO- 10019 This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 19  Fixture tool: FO- scratches on the polished 10019 ferrule. This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 20 This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 21 TX00.285 on the left pictures. If not, repeat from step 2. This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 22 This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 23 Apex Offset[um]: Min 0.0 – Max 50.0 If fail, repeat from step 3. This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 24 This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.

  • Page 25: Appendix

    Tool drawing for crimping the ground contact to the rear body (FOH) This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.
  • Page 26 Assembly instructions rev. 6.1 This document is the property of Fischer Connectors. This document must not be reproduced or distributed, in whole or in part, without prior written permission of Fischer Connectors.

Table of Contents