Rayzist 2034vx Manual
  1. Manuals
  2. Brands
  3. Rayzist Manuals
  4. Industrial Equipment
  5. 2034vx
  6. Manual

Rayzist 2034vx Manual

Sandcarving system
Hide thumbs
Table of Contents

Advertisement

Quick Links

 
2034vx   / 2034vxa  
Sandcarving   S ystem  
 

Advertisement

Table of Contents
loading

Summary of Contents for Rayzist 2034vx

  • Page 1   2034vx   / 2034vxa   Sandcarving   S ystem    ...
  • Page 3 Table of Contents Section 1 - Safety Information Section 2 - Setup Guide Section 3 - Operation Section 4 - Maintenance 1/20/2015 (3:46 PM) 2034vx & 2034vxa v6.0.doc...
  • Page 4 Air Inlet Valve Abrasive Flow Valve Foot Switch Valve Footpedal Water Seperator Air Pressure Regulator Gauge Union Nut Blast Hose Pressure Pot Closure Lever Air Inlet Valve Quick Disconnect Blast Nozzle Nozzle Holder 1/20/2015 (3:46 PM) 2034vx & 2034vxa v6.0.doc...

  • Page 5: Safety Information

    Do not blast materials that may produce and supply with your cabinet, 150 grit Brown combustible dusts. Never use flammable solvents Aluminum Oxide, MSDS information is provided in inside the cabinet. your information package. 1/20/2015 (3:46 PM) 2034vx & 2034vxa v6.0.doc...

  • Page 6: Pressure Pot

    SET incoming air pressure from air compressor between 80psi to 90psi. Set blasting pressure regulator on the pot to desired blasting pressure, normally between 25 psi - 35 psi. 1/20/2015 (3:46 PM) 2034vx & 2034vxa v6.0.doc...

  • Page 7: Set-Up Instruction

    If there are any external or internal damages to the Tools Needed: 2.1.1 equipment it must be noted on the carrier’s bill of lading. Contact Rayzist customer service at 1-800- • ¾" open end wrench, ¾" socket wrench, or 729-9478 immediately to process a damage claim. crescent wrench.

  • Page 8: Removal From Pallet

    Connect the short hose to quick disconnect fitting on footswitch valve (E). Connect the long hose to the quick disconnect fitting located between water separator (G) and the air inlet valve (C). 2034vxa Model 1/20/2015 (3:46 PM) 2034vx & 2034vxa v6.0.doc...

  • Page 9: Electrical Connection

    Exhausting through a long vent pipe may require an additional exhaust fan installed at the point the vent exits the building. 1/20/2015 (3:46 PM) 2034vx & 2034vxa v6.0.doc...

  • Page 10: Height Adjustment

    2.13 Dedicated Air Compressor Set-up 2.14 Height Adjustment The 2034vx Adjustable Sandcarving system 2.14.1 ! NOTICE has an electrically powered height adjustment switch. Height measured at the arm holes can be DO NOT connect air to the cabinet until you are adjusted from 39 to 53 inches.
  • Page 11 The Pressure Pot compressor has been set up according to has two adjustment ball valves that can regulate the instructions found in the Rayzist setup guide. abrasive/air flow mixture. The standard settings for the pressure pot should be made as follows: Connect the compressor air hose to the Air 3.2.2...
  • Page 12 (C) and try again. If for some reason you cannot get the pressure pot closure cap 3.6 Sandcarving to seal, call Rayzist and ask for technical help. Turn on cabinet power switch located above 3.6.1 3.4 Adjusting Blasting Pressure.
  • Page 13 You can get additional abrasive to fall back into the pot by tapping on the outside of the cabinet just above the pot. The pot is now filled again and is ready for the next time you blast. 1/20/2015 (3:46 PM) 2034vx & 2034vxa v6.0.doc...

  • Page 14: Daily Maintenance

    36 to 40 Inches long. Bags are available through Abrasive life expectancy may be 15 to 20 4.4.1.1 Rayzist or your local plastic bag company. hours of blasting. Worn abrasive does not cut as fast as new abrasive and will generate more dust inside the cabinet during blasting.
  • Page 15 To replace sleeve, Disconnect air and 4.6.1.2 Viewing Glass Replacement DEPRESSURIZE the pressure pot according to the instructions in operation manual. 1/20/2015 (3:46 PM) 2034vx & 2034vxa v6.0.doc...
  • Page 16 (instructions for these are supplied with the replacement parts). Blast Hose (K). 4.8.1 Weather Strip Seal on doors. 4.8.2 Light bulb replacement – Always Turn off 4.8.3 unplug power from the unit. Do not exceed 100 watt bulbs. 1/20/2015 (3:46 PM) 2034vx & 2034vxa v6.0.doc...

  • Page 17: Switch Wiring Diagram

    Blower Motor Electrical Connection Box Black Black Motor Leads 22mm Ground Lever Action Black Double Pole 10A Switch Contact Black Black Green w/ Yellow White Copper Enclosed Halogen Light Fixture 100w Lamp 220 VAC 1/20/2015 (3:46 PM) 2034vx & 2034vxa v6.0.doc...
  • Page 18 Actuator Switch Ground Lever Action Double Pole 10 A Connection Box Switch Con tact Black AC/DC Converter White Black Black Blue White actuator Copper Yellow Enclosed Halogen Light Fixture 100w Lamp 220 VAC 1/20/2015 (3:46 PM) 2034vx & 2034vxa v6.0.doc...
  • Page 20 RAYZIST.COM | 800.729.9478 ORDER ONLINE: WWW.RAYZIST.COM/STORE...

This manual is also suitable for:

2034vxa

Table of Contents