Subscribe to Our Youtube Channel
Related Manuals for Matrix MW402
Summary of Contents for Matrix MW402
- Page 1 Manual for installation, use and maintenance MW402 Integrated Dishwasher year parts 1 year labour guarantee www.matrixappliances.co.uk...
-
Page 2: Table Of Contents
Contents: Important information Important notes Recommendations Steps before first use Using your appliance Starting a programme Changing a programme Cancelling a programme Detergent Salt Softener adjustment Rinse aid Dishwasher baskets Standard loading and test data Programme listing Care and maintenance Failure codes and troubleshooting Troubleshooting Electrical information... - Page 3 Important • Read the instructions prior to installation and use of the appliance. • Do not lean or climb on the open dishwasher door, to prevent damage. • Close the dishwasher door after use, to prevent accidents. • Use only detergents, salt and rinse aid specifically designed for dishwashers.
- Page 4 electrically operated valve. The wires that connect to this valve are inside the inlet hose. Do not cut through the inlet hose, and do not put the plastic housing in water. • Children could get locked inside the appliance. Therefore when disposing of an old appliance, cut off the plug and set aside, and damage the door lock so that the door can no longer be closed.
-
Page 5: Important Information
Appliance information Please enter the details on the appliance rating plate below for reference, to assist CDA Customer Care in the event of a fault with your appliance and to register your appliance for guarantee purposes. Appliance Model Serial Number EU Declarations of Conformity This product meets the requirements of all applicable EU directives with the corresponding harmonised standards, which provide for CE marking. - Page 6 65°C intensive 65°C express 50°C eco prewash programme MW402 salt rinse aid programme Fig. 1 “Power” button (1) To switch the dishwasher on or off, press the “Power” button (1). When you switch on the dishwasher, the “End of Programme” light will illuminate, and two dashes will appear on the display.
-
Page 7: Starting A Programme
selected. If there is a fault on the dishwasher, the fault code will show on these lights. “Salt” and “Rinse Aid” warning lights and “End of Programme” light (4) When either the dishwasher salt or rinse aid begins to run out, a warning light will illuminate to advise that it needs refilling. -
Page 8: Changing A Programme
Changing a programme It is possible to change the programme, if necessary, once the programme has started. • First open the door slightly to reduce the risk of water spillage. • Press the “Programme Selection” button until the required programme is shown on the display. -
Page 9: Detergent
Detergent To fill the detergent compartment • Push the latch to open the compartment. • Add the required amount of detergent. Fig. 2 The main detergent compartment “b” (Fig. 2) has lines to allow for specific amounts of detergent. These are marked at either 15cm 3 or 25cm 3 , to be used depending on how dirty the dishes are. -
Page 10: Salt
setting to the minimum. When you then use separate detergents again, you should fill the salt and rinse aid compartments, adjust the water hardness setting to the maximum and run an empty wash, then adjust the water hardness setting and the rinse aid setting to the appropriate level. -
Page 11: Softener Adjustment
When the salt warning light on the control panel illuminates, you should refill the salt compartment with salt only – do not add water to the salt compartment after the first use. Important: You should run a prewash programme immediately after adding dishwasher salt, to prevent any damage to the dishwasher system. -
Page 12: Rinse Aid
If the hardness of the water you use is above 63dE, or if you are using well water, you are recommended to contact your local water board to confirm the water hardness level and to use filter and water refinement devices. - Page 13 In order to change the rinse aid level, follow the steps below before turning on the machine: 1. Press and hold down the programme selection button 2. Press the Power button to switch on the dishwasher 3. Keep the programme selection button pressed until “rA”...
-
Page 14: Dishwasher Baskets
underwater environments deprived of oxygen that are subsequently unable to support life. Please consider the environment and, if you wish to use rinse aid, try to source an environmentally friendly brand. Dishwasher Baskets To adjust the height of the upper basket •... -
Page 15: Standard Loading And Test Data
Standard Loading and Test Data Capacity • Upper and lower baskets: 12 place settings. • The upper basket should be adjusted to high position. • Cups should be placed onto the dish rack pins. Detergent / Rinse aid • 5 + 25cm , in accordance with EN50242-DIN 44990 IEC436 (international norms) / Rinse aid... -
Page 16: Programme Listing
Programme Programme Intensive Express Prewash listing name and 65 ° 65 ° 50 ° temperature The values and Level of soil High Medium Medium times provided in the adjacent table have Detergent required been obtained under Prewash Prewash Prewash laboratory conditions according to relevant 50 °... -
Page 17: Care And Maintenance
Care and maintenance Before beginning any care or maintenance, you should always disconnect the appliance from the electricity supply, and also turn off the water supply. Door seals Fig. 13 Wipe the dishwasher door seals regularly with a damp cloth to remove any residues. - Page 18 Please note: Never run a programme without the filters in place. Incorrect fitting of the filters may reduce wash performance and potentially damage your appliance. Spray arms You should clean the spray arms at least once a month. • Remove the lower basket. •...
-
Page 19: Failure Codes And Troubleshooting
Failure codes and troubleshooting The “Programme Indicators” also serve as a diagnostic display to help in the event of a problem with the appliance. Error Code Error description Advice Intensive Express Prewash Make sure the water inlet tap is fully open. - Page 20 Failure Codes and Troubleshooting Problem Possible cause Check the plug, fuse and circuit breakers of the mains supply. The water tap is turned off. The programme will not start. The dishwasher door is not fully closed. The water inlet filter or the machine filters are blocked.
-
Page 21: Electrical Information
Electrical Information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13A fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. - Page 22 • The wire which is coloured GREEN and YELLOW must be connected to the terminal which is marked with letter (E) or by the Earth symbol coloured GREEN and YELLOW. • The wire which is coloured BLUE must be connected to the terminal which is marked with the letter (N) or coloured BLACK or BLUE.
-
Page 23: Installation
Installation • Do not install this appliance if it is damaged in any way. Installing a damaged appliance may invalidate the warranty and could cause further damage to the surrounding area. • Do not hold the appliance by the door or control panel to move it as this may cause damage. - Page 24 Figures 14 and 15 on page 25 show the recommended installations of our dishwashers. The set-ups in these figures should be mimicked wherever possible to help to ensure the best performance of the appli- ance. Please carry out the below checks/measures before, during and after installation.
- Page 25 • Use the additional fitting template and kit supplied with the appliance to fit the appliance into the cabinet, secure it and fit and secure the decor door. • Adjust the dishwasher door hinge tension as necessary to ensure the appliance door opens and closes properly and safely with the decor door attached.
-
Page 26: Fitting The Decor Door
Fitting the decor door Where non-standard decor doors are to be used, additional fitting in- structions are required to ensure compatibility with this product. The appliance is supplied with a fitting template and these instructions should be followed as normal. However, the fitting template needs to be located lower down the fascia door. - Page 27 FICHE Supplier's trade mark Matrix MW402 Supplier's model Capacity of dishwasher The energy e ciency class A ++ Annual energy consumption in kWh per year (AE ) ( 280 Cycle )* Energy consumption (E ) (kWh per cycle) 0,90 O mode power consumption (W) (P...
- Page 28 Serviced by For our Customer Care Department, or for Service, please contact us on: The CDA Group Ltd. Harby Road, Langar, Nottinghamshire, NG13 9HY Tel: 01949 862012 Fax: 01949 862003 Email: customer.care@cda.eu...
Need help?
Do you have a question about the MW402 and is the answer not in the manual?
Questions and answers