Table of Contents
Advertisement
Diligent Instruments Corporation
Address: 2802 Fanshawe Street Philadelphia, PA 19149
Phone: (215)316-4516
Email: dlginstruments@gmail.com
www.diligentinstruments.com
Product distributed in the United States by Diligent
Instruments Corporation and made in China.
OPERATING MANUAL
Model：
DI-215(12V)
DI-215A(12V/24V)
V3
DLG
AUTOMOTIVE BATTERY
SYSTEM ANALYZER
Advertisement
Table of Contents
Related Manuals for DLG DI-215
Summary of Contents for DLG DI-215
- Page 1 AUTOMOTIVE BATTERY SYSTEM ANALYZER OPERATING MANUAL Model： DI-215(12V) DI-215A(12V/24V) Diligent Instruments Corporation Address: 2802 Fanshawe Street Philadelphia, PA 19149 Phone: (215)316-4516 Email: dlginstruments@gmail.com www.diligentinstruments.com Product distributed in the United States by Diligent Instruments Corporation and made in China.
-
Page 2: Table Of Contents
★ DIN－Deutsches Institut für Normung e.V. C O N T E N T Under a cold temperature of 0°F（-18°C）, the Ampere quantity is 9.0V … … … … … … … … … … … … … … … … … … … … … … … …1 1. -
Page 3: Brief Introduction
This is a standard written by Japanese Industrial Standard (JIS). It is (2) The working voltage of DI-215 is DC 9V to 18V, while that of DI-215A explained that the battery discharges with a fixed ampere for 20 hours along refers to DC 9V to 35V. - Page 4 8. Knowledge About Automobile Battery minutes, then check the battery when it’s voltage value drop to the normal value. 8-1 the internal resistance of different types of battery differ (4) Check the insulating layer of the clamps before measuring. Damage, The internal resistance differs because of inconformity of internal bareness and disconnection are unacceptable.
-
Page 5: International Electric Symbol
3.International Electric Symbol continue table M o d e l T h e s a me m od el M od el Th e sa me m od e l 5 4 5 2 3 54 524 5852 1 5851 3 5 4 53 7 5 4 5 45 5480 1... -
Page 6: Storage Battery Test
continue table 5-2 storage battery test Ba tter y B at ter y CC A CC A 5-2-1 preparation NE W JI S O L D JI S C MF N E W J I S O L D JI S C M F If the engine is working, please turn off first and switch the key to off 34 B1 9R S N S4 0Z AS... - Page 7 continue table B a t t e r y Ba tt er y C C A C C A N E W J I S O L D J I S C M F N E W J I S O L D J I S C M F 2 9 5...
- Page 8 The load test method: According to the physical formula R=V/1, test batteries in series.( only DI-215A) equipment forcibly make the high permanent DC current ( presently 40-80A Internal insulation 4.75mΩ The higher of the CCA value , the lower of the internal insulation large current is available ) go through the battery shortly ( about 2-3 seconds).
-
Page 9: Engine System Activation Load Test
The result indicates the battery is good and full of 100% of life. But only 6-2 Can it be affected by the installation of negative current 12.11V left. SO suggest charging. inside the vehicle? ★ Life check OK, and voltage check over low All the negative currency will affect the result. -
Page 10: Maximum Load System Test
★ If the voltage is lower than 13.30V,(for 24V system<DI-215A>, the As can be seen in the picture current test voltage is 12.36V, standard voltage reading is under 26.60V), please check the connections, wires and the is 9.6V,(for 24V system<DI-215A>, standard voltage is 16V), the lowest engine. -
Page 11: Charging System Test
5-5-2 Procedure of operation (2)Turn on all the devices such as lights, warning system , air-condition. (1) When the engine is working, connect the red clamp to the positive polar of (3)Speed the engine to 2000 rpm and keep this state for 15 seconds. (4) Press <▲><▼>to select maximum load system test as the picture below: the battery, and the black one to the negative polar.
Need help?
Do you have a question about the DI-215 and is the answer not in the manual?
Questions and answers