Table of Contents
Advertisement
en
Cleaning the filters (F)
To clean the Hepa 14 filter (38) :
1.
Detach the air grill (39) using the opening tab
and remove the sponge (40) (F1).
2.
Remove the Hepa 14 filter by releasing the
opening tab (F2).
3.
Clean the filter and sponge by washing them
under running water, while making sure that the
water jet is not too strong (F5).
4.
Hold the filter so that the water flows parallel to
its folds.
5.
Leave the filter and sponge to dry at room
temperature until all their components are
completely dry (F6).
6.
Put the Hepa 14 filter back in place, paying
attention to the position of the notches.
7.
Fit the sponge on the air grill and mount it onto its
housing until it clicks into place.
To clean the Multicyclonic filter (37):
1.
Press the dustin release button (36) on the
handle (23) and take out the dustbin.
2.
Open using the lever of the handle on the dustbin
as demonstrated in the picture (F3).
3.
Pull out the filter by the opening tab (F4).
4.
Clean the filter by washing it under running wa-
ter, taking care that the jet of water is not too
strong (F5).
5.
Let it dry at room temperature until its parts are
thoroughly dry (F6).
6.
Fit the filter into the special housing inside the
dustbin.
7.
Close the dustbin handle.
ATTACHMENTS
MOTORISED BRUSH
The Motorised brush (1) is suitable for vacuuming
carpets and hard floors on a daily basis.
It is designed to reach a deeper dust cleaning
efficiency on the carpet. The Motorised brush can
comb and separate the furs of the carpet with high
frequency cleaning to remove the fine dust in the
bottom of carpet.
Using the motorised brush
When the product is in the park position, the
Start&Pause function of the motorised brush switches
off the operation of the UV light and the rotating brush,
while the suction power in on. In this position it is
possible to use the other accessories in the clamp (7).
10
10
To pause the vacuum cleaner use the standby button
(26) on the Remote Power Control (14), and to restart
the suction power press the standby button (see
chapters "Using the vacuum cleaner" and "Features"
in the user manual).
When the product is not in the upright position, press
the motorised brush ON/OFF switch on the handle
(41), to turn on or off the UV light and to switch on
or off the motorised brush. When switching off the
motorised brush ON/OFF switch, the UV light and the
rotating brush are off. To turn on the UV light and to
restart the brush switch on the motorised brush button.
To pause the vacuum cleaner use the standby button
(26) on the Remote Power Control (14) and to restart
the suction power press the standby button (see
chapters "Using the vacuum cleaner" and "Features"
in the user manual).
Cleaning the motorised brush
Before cleaning or maintaining the motorised brush of
the vacuum cleaner, make sure it has been unplugged
from electrical outlet. Always disconnect the motorised
brush before cleaning it.
•
Open the brush roll cover locking by unscrewing
the two screws (42) (G).
•
Remove the roll cover accordingly in the direction
as shown in the figure (G).
•
Remove the roll out of the notch for cleaning.
•
Avoid cleaning with water.
•
Reassemble in the reverse order
Ultraviolet light
The UV light (2, if available) is an ultraviolet
sterilization function, when the brush is collecting dust
on the ground normally, the UV light will be active and
the antiseptic function is working. When the brush is
not in contact with a horizontal surface, the UV light is
switched off. To replace the UV light, please contact
the nearest Authorised Service Centre.
BRUSH FOR DEEP CLEANING
The brush for deep cleaning (3) is designed to
optimise the air flow and is particularly suitable for
vacuum cleaning heavily soiled carpets and irregular
surfaces. For this reason, the brush may adhere
strongly to vertical surfaces and can be difficult to
remove. In these cases, it is advisable to use the
minimum suction power or open the air regulator (13)
on the handle, or use the motorised brush. This brush
should not be used on PVC floors and especially on
parquet floors: in this latter case, use the parquet
brush designed for use on parquet flooring.
Advertisement
Table of Contents
