Summary of Contents for BOSER Technology HS-7165
- Page 1 HS-7165 Intel® Mobile Dual-Core processor PICMG1.3 Full-size SBC •1066/800MHz FSB•CompactFlash• •DVI-I/CRT/LVDS•Dual GB LAN• •Audio•SATA•RS-232/422/485•4 COM• •7 USB2.0•WDT•H/W Monitor•...
- Page 2 Copyright Disclaimers The accuracy of contents in this manual has passed thorough checking and review before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for manufacturer will any infringements of patents or other rights resulting from its use. The...
-
Page 3: Table Of Contents
Table of Contents Chapter 1 General Description ........1 1.1 Major Features ............... 2 1.2 Specifications ................ 2 1.3 Board Dimensions..............4 Chapter 2 Unpacking ..........5 2.1 Opening the Delivery Package..........5 2.2 Inspection................5 Chapter 3 Hardware Installation ......7 3.1 Before Installation ..............7 3.2 Board Layout ................. - Page 4 Chapter 4 AMI BIOS Setup ........25 4.1 Starting Setup..............25 4.2 Using Setup ................. 26 4.3 Main Menu................27 4.4 Advanced Settings .............. 28 4.5 Advanced PCI/PnP Settings..........31 4.6 Boot Settings ............... 32 4.7 Security Settings ..............33 4.8 Advanced Chipset Settings..........
- Page 5 Declaration of Conformity -- CE Mark BOSER Technology hereby acknowledges that compliance testing in accordance with applicable standards of the EU’s EMC Directive, 89/336/EEC, was successfully completed on a sample of the equipment identified below: Equipment Class: Information Technology Equipment...
- Page 6 Fasten the ALLIGATOR clip of the strap to the end of the shielded wire lead from a grounded object. Please wear and connect the strap before handle the HS-7165 to ensure harmlessly discharge any static electricity through the strap.
-
Page 7: Chapter 1 General Description
The HS-7165 is an Intel® GM45/ICH9-M chipset-based board designed, the board supports Intel® Mobile Dual-Core processor. The HS-7165 is an ideal all-in-one PICMG1.3 single board computer. Additional features include an enhanced I/O with CF, DVI-I/CRT/LVDS, dual GB LAN, audio, SATA, 4 COM, and 7 USB2.0 interfaces. -
Page 8: Major Features
(WDT) onboard , the HS-7165 is designed with software that does not need the arithmetical functions of a real-time clock chip. If any program causes unexpected halts to the system, the onboard WDT will automatically reset the CPU or generate an interrupt to resolve such condition. - Page 9 H/W Status Monitor: Monitoring temperatures, voltages, and cooling fan status Power Function Supports ATX power mode Operating Temperature 0~60 degrees C Operating Humidity 0~95%, non-condensing Size (L x W) 338 x 126 mm I/O Interface MIO: 3 x RS-232 1 x RS-232/422/485 7 x USB2.0 (6 x internal, 1 x external) 1 x Parallel 4 x SATA...
-
Page 10: Board Dimensions
Board Dimensions... -
Page 11: Chapter 2 Unpacking
Chapter 2 Unpacking Opening the Delivery Package The HS-7165 is packed in an anti-static bag. The board has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety Instructions in front of this manual describe anti-static precautions and procedures. - Page 12 Cables Package Description QTY. SATA cable 50cm (w/Lock) COM DB9*2-10P(2.54) 30cm w/bracket Print DB25-26P(2.54) 30cm w/bracket SPK 8P(2.54) phone jack*2 27cm w/bracket SATA power cable 15cm USB 1-to-2 cable w/bracket 20cm 6P(JST2.0)-Mini DIN*2 cable 20cm w/bracket It is recommended that you keep all the parts of the delivery package intact and store them in a safe/dry place for any unforeseen event requiring the return shipment of the product.
-
Page 13: Chapter 3 Hardware Installation
Chapter 3 Hardware Installation This chapter provides the information on how to install the hardware using the HS-7165. This chapter also contains information related to jumper settings of switch, and watchdog timer selection etc. Before Installation After confirming your package contents, you are now ready to install your hardware. -
Page 14: Board Layout
Board Layout... -
Page 15: Jumper List
Jumper List Jumper Default Setting Setting Page Panel Voltage Select: +3.3V Short 2-3 Clear CMOS: Normal Operation Short 1-2 JP10 Short 1-2 FSB Frequency Select: Auto Detect JP11 Short 1-2 JP12 Short 2-3 JP13 Short 1-2 JP14 Short 1-2 CF or SATA 3 Connector Select: SATA 13/17 JP15 Short 1-2... -
Page 16: Configuring The Cpu
CN6/CN5. It supports DDR2 up to 4GB SDRAM. VGA Controller The HS-7165 provides four types of connection for display device. CN27 is a 15-pin CRT connector. CN3/CN4 are the LVDS interface connectors onboard reserved for flat panel installation. HS-7165 also provides DVI-I connector at location CN23. - Page 17 DVI-I Version Settings Options JP18 JP19 DVI-I Function (default) Short 1-2 Open External PCIe x16 Short 2-3 Short CN27: 15-pin CRT Connector PIN Description PIN Description Green Blue DDCDA HSYNC VSYNC DDCCL CN3/CN4: LVDS Interface Connector PIN Description PIN Description A0-/B0- A0+/B0+ A1-/B1-...
- Page 18 If you want to use 48-bit dual channel LVDS panel, please use CN3 and CN4 combined. The HS-7165 has an onboard jumper that selects the working voltage of the flat panel connected to the system. Jumper JP2 offers two voltage settings for the user.
-
Page 19: Serial Ata Connector
JP15 JP16 SATA 3 (default) Short 1-2 Short 2-3 Serial Port Connectors The HS-7165 offers 16C550 compatible UARTs with Send/ Receive 16-byte FIFO serial ports. CN31/CN30/CN29/CN28: COM 1 ~ COM 4 Connector (5x2 Header) PIN Description PIN Description Don’t Use... - Page 20 CN14: RS-422/485 Connector (3x2 Header, COM 4) PIN Description PIN Description NOTE: The terminal resistance of RX & TX is set at 180 Ω CN13: COM 4 use RS-232 or RS-422/485 Select Options Settings RS-232 (default) Open RS-485 Transmit Only (*1) Short 1-2, 3-4, 5-7, 8-10 RS-485 by –RTS (*-1) Short 1-2, 3-4, 7-9, 8-10...
-
Page 21: Ethernet Connector
3.10 Ethernet Connector The HS-7165 provides two RJ-45 connectors for 10/100/1000 Based LAN. Please refer to the following for its pin information. When installs OS, this driver namely can automatically install. User does not need to renewal. CN19/CN20: RJ-45 Connector... -
Page 22: Cmos Data Clear
3.12 CMOS Data Clear The HS-7165 has a Clear CMOS jumper on JP4. JP4: Clear CMOS Options Settings Normal Operation (default) Short 1-2 Clear CMOS Short 2-3 IMPORTANT: Before you turn on the power of your system, please set JP4 to open for normal operation. -
Page 23: Power And Fan Connectors
3.14 Power and Fan Connectors HS-7165 provides one 4-pin power in at CN13. Connector FN2 onboard HS-7165 is a 3-pin +12V fan power output connector. FN1/FN2: Fan Power Connector Description +12V Fan In PW1: 4-pin ATX Power Connector PIN Description... -
Page 24: System Front Panel Control
A reset system signal will restart when such error happens. The HS-7165 custom WDT circuit is implemented using the internal IO of the Winbond Super I/O W83627UHG which is at 2Eh of LPC. The following sample programs show how to enable, disable and... - Page 25 Sample Code C Language for Watchdog Timer under DOS. #include<stdio.h> #include<dos.h> static unsigned int 83627UHG_Port = 0x2e; Outportb(83627UHG_Port,0x87); Outportb(83627UHG_Port,0x87); void W83627UHG_WDT(unsigned int count_setup) unsigned int Counting, Register_Setup; outportb(83627UHG_Port, 0x07); outportb(83627UHG_Port+1, 8); // set as Logical Device 8 if(count_value >= 60) outportb(83627UHG_Port, 0xf5);...
-
Page 26: Audio Connectors
0xf6); outportb(83627UHG_Port+1, counting); // set WDT count value 3.18 Audio Connectors The HS-7165 has an onboard RealTek ALC202A audio connector. The following tables list the pin assignments of the Line In/Audio Out connector. CN24: MIC In/Line Out Connector PIN Description PIN Description... -
Page 27: External Pcie Slot
Short 2-3 Short 3.20 CompactFlash Connector The HS-7165 also offers a Type I/II CompactFlash connector is IDE interface located at the solder side of the board. The designated CN17 connector, once soldered with an adapter, can hold CompactFlash cards of various sizes. Please turn off the power before inserting the CF card. - Page 28 CN17: CompactFlash Connector Description Description DATA3 DATA4 DATA5 DATA6 DATA7 SDCS1# SDA2 SDA1 SDA0 DATA0 DATA1 DATA2 470Ω pull GND DATA11 DATA12 DATA13 DATA14 DATA15 SDCS3# EWE0 RESET IORDY DACK IDE LED PDIAG DATA8 DATA9 DATA10 NOTE: When use CF card, IDE device function will be disabled.
-
Page 29: 8-Bit Gpio Function
3.21 8-bit GPIO Function The HS-7165 offers one 8-bit input/output port. CN10: 8-bit GPIO PIN Description PIN Description EX. Sample Code Using GPIO 5 #include <conio.h> #include <stdio.h> #include <io.h> void main(void) unsigned char byte_cr29; outportb(0x2e, 0x87); // enter Super I/O configuration mode outportb(0x2e, 0x87);... - Page 30 This page is the blank page.
-
Page 31: Chapter 4 Ami Bios Setup
Chapter 4 AMI BIOS Setup The HS-7165 uses AMI BIOS for the system configuration. The AMI BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options that could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features. -
Page 32: Using Setup
Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, use the <PageUp> and <PageDown> keys to change entries, and press <Esc> to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard. Move to previous item ↑... -
Page 33: Main Menu
Main Menu Once you enter the AMI BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter>... -
Page 34: Advanced Settings
Advanced Settings This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Advanced Settings WARNING: Setting wrong values in below sections... - Page 35 BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit IDE Configuration Configure SATA#1 as [IDE] SATA PORT0 : [Not Detected] SATA PORT1 : [Not Detected] SATA PORT2 : [Not Detected] Select Screen SATA PORT3 : [Not Detected] Select Item - Change Field Select Field General Help...
- Page 36 BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit ACPI Settings Suspend mode [Auto] Select Screen Select Item Change Field Select Field General Help Save and Exit Exit v02.61 (C)Copyright 1985-2006, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security...
-
Page 37: Advanced Pci/Pnp Settings
Advanced PCI/PnP Settings This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system that allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. -
Page 38: Boot Settings
Boot Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Boot Settings Boot Settings Configuration Select Screen Select Item Change Field Select Field General Help Save and Exit Exit v02.61 (C)Copyright 1985-2006, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP... -
Page 39: Security Settings
Security Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Security Settings Supervisor Password : Not Installed User Password : Not Installed Select Screen Change Supervisor Password Select Item Change User Password Change Field Boot Sector Virus Protection [Disabled] Select Field General Help... -
Page 40: Advanced Chipset Settings
Advanced Chipset Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Advanced Chipset Settings WARNING: Setting wrong values in below sections may cause system to malfunction. North Bridge Configuration Select Screen South Bridge Configuration Select Item Change Field Select Field General Help Save and Exit... -
Page 41: Exit Options
BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Sorth Bridge Chipset Configuration PCIE Ports Configuration PCIE Port 0 [Auto] PCIE Port 1 [Auto] Select Screen PCIE Port 2 [Auto] Select Item PCIE Port 3 [Auto] - Change Field PCIE Port 4 [Auto] Select Field... - Page 42 This is the blank page.
-
Page 43: Chapter 5 Software Utilities
Chapter 5 Software Utilities This chapter contains the detailed information about installation procedures of chipset, VGA, LAN, audio and other drivers. The utility CD disk that comes with the package contains an auto-run program that invokes the installation programs for the chipset, VGA, LAN and audio drivers. - Page 44 Immediately after clicking the CHIPSET button in Step 1, the program launches the Setup that will assist you in the installation process. Click on the Next > button to proceed. The License Agreement dialog box then appears on the screen. Choose Yes to proceed.
- Page 45 When the Readme File Information dialog box pops up, just clock on the Next> button to proceed. Click on the Finish to completed the installation.
-
Page 46: Vga Driver Installation
VGA Driver Installation Insert the CD that comes with the board into the CD-ROM drive. Click VGA to install Intel® GM45 video driver. The Welcome to the Setup program dialog box appears on the screen. Choose Next> to proceed. - Page 47 The Intel® License Agreement dialog box appears on the screen. Choose Yes to proceed. When the Readme File Information dialog box pops up, just click on the Next> button to proceed.
- Page 48 The Installshield Wizard dialog box appears on the screen. Click on Next> to proceed. When Setup Progress finished, just click on Next button to proceed.
-
Page 49: Lan Driver Installation
Please select “Yes, I want to restart my computer now” button then click “Finish” to reboot your system to take the effect once the installation is completed. LAN Driver Installation Insert the CD that comes with the board into the CD-ROM drive. Click LAN to install RTL8111 LAN driver. - Page 50 When the dialog box below appears, make sure you close all other Windows applications the click on the Next> button to proceed. The Setup Status dialog box then appears on the screen.
-
Page 51: Audio Driver Installation
When setup is finished, please reboot your computer to take the effect. Audio Driver Installation Insert the CD that comes with the board into the CD-ROM drive. Click Audio to install audio driver. - Page 52 When the dialog box below appears, Click on Yes to proceed. Please select “Yes, I want to restart my computer now” button then click “Finish” to reboot your system to take the effect once the installation is completed.