Page 4
Option 39. Personal Preferance Equalizer Band 1..............39 Option 40. Personal Preferance Equalizer Band 2..............39 Option 41. Personal Preferance Equalizer Band 3..............39 Option 42. Personal Preferance Equalizer Band 4..............39 Option 43. Personal Preferance Equalizer Band 5..............39 Option 44. Sound Efect (Standard; Music; Speech; Jazz; Pp)..........39 Option 45.
1.INTRODUCTION 11AK45 is a 50Hz colour television capable of driving 24” + CRT sizes( beginning from 24” 16:9 up to 33”). The chassis is capable of operation in PAL, SECAM, NTSC (playback) colour standards and multiple transmission standards as B/G, D/K, I/I’, and L/L´. Sound system output is supplying 2x10W (10%THD) for left and right outputs of 8ohm speakers.
4.VIDEO SWITCH TEA6415 In case of three or more external sources are used, the video switch IC TEA6415 is used. The main function of this device is to switch 8 video-input sources on the 6 outputs. Each output can be switched on only one of each input. On each input an alignment of the lowest level of the signal is made (bottom of sync.
9.POWER SUPPLY (SMPS) The DC voltages required at various parts of the chassis are provided by an SMPS transformer controlled by the IC MC44608, which is designed for driving, controlling and protecting switching transistor of SMPS. The transformer generates 145V for FBT input, +/-14V for audio amplifier, 5V and 3.3V stand by voltage and 8V, 12V and 5V supplies for other different parts of the chassis.
• Up to 16 Colours per DRCS Character • One out of Eight Colours for Foreground and Background Colours for 1-bit DRCS and ROM Characters • Shadowing • Contrast Reduction • Pixel by Pixel Shiftable Cursor With up to 4 Different Colours •...
K9356M: Standard B/G, D/K, I, L Features TV IF audio filter with pass band for sound carriers at 32,40 MHz (D/K, L), 32,90 MHz (I) and 33,40 MHz (B/G) K3953M Terminal and Pin configuration are the same with K9656M: Standard B/G, D/K, I, L/L’...
• Low power consumption • Short-circuit resistant • High performance • high signal-to-noise ratio • High slew rate • Low distortion • Large output voltage swing. 13.2.3.Pinning SYMBOL DESCRIPTION OUTA Output A INA(neg) Inverting input A INA(pos) Non-inverting input A Negative supply INB(pos) Non-inverting input B...
13.3.2.Features Standard Selection with single I C transmission Automatic Standard Detection of terrestrial TV standards Automatic Sound Selection (mono/stereo/bilingual), new registers MODUS, STATUS Two selectable sound IF (SIF) inputs Automatic Carrier Mute function Interrupt output programmable (indicating status change) Loudspeaker / Headphone channel with volume, balance, bass, treble, loudness AVC: Automatic Volume Correction Subwoofer output with programmable low-pass and complementary high-pass filter 5-band graphic equalizer for loudspeaker channel...
Not connected Not connected AVSS Analog ground AVSS Analog ground MONO_IN Mono input Not connected Reference voltage IF A/D VREFTOP converter SC1_IN_R SCART 1 input, right SC1_IN_L SCART 1 input, left ASG1 AHVSS Analog Shield Ground 1 SC2_IN_R SCART 2 input, right SC2_IN_L SCART 2 input, left ASG2...
13.4.2.Features Video Decoding and Processing – four CVBS, one S-VHS input, one YC component input – integrated high-quality A/D converters and associated clamp and AGC circuits – adaptive 2H comb filter Y/C separator – multistandard colour decoder PAL/NTSC/SECAM including all substandards –...
• 6.5dB gain between any input and output • 55dB crosstalk at 5mHz • Fully ESD protected 13.5.3.Pinning Input Max : 2Vpp, Input Current: 1mA, Max : 3mA Data Low level : -0.3V Max: 1.5V, High level : 3.0V Max : Vcc+0.5V Input Max : 2Vpp, Input Current: 1mA, Max : 3mA Clock...
13.7.TDA7269A 13.7.1.Description The TDA7269A is class AB dual Audio power amplifier assembled in the Multiwatt package, specially designed for high quality sound application as Hi-Fi music centers and stereo TV sets. 13.7.2.Features Wide Supply Voltage Range Up To ±20V Split Supply High Output Power 14 + 14W @THD =10%, R =8Ω,V...
Memory • Non-multiplexed 8-bit data and 16 … 20-bit address bus (ROMless Version) • Memory banking up to 1Mbyte (Romless version) • Up to 128 Kilobyte on Chip Program ROM • Eight 16-bit data pointer registers (DPTR) • 256-bytes on-chip Processor Internal RAM (IRAM) •...
external components while offering a high flexibility and reliability. The device also features a very high efficiency stand–by management consisting of an effective Pulsed Mode operation. This technique enables the reduction of the stand–by power consumption to approximately 1W while delivering 300mW in a 150W SMPS.
13.12.TCET1102G 13.12.1.Description The TCET110/ TCET2100/ TCET4100 consists of a phototransistor optically coupled to a gallium arsenide infrared-emitting diode in a 4-lead up to 16-lead plastic dual inline package. The elements are mounted on one lead frame using a coplanar technique, providing a fixed distance between input and output for highest safety requirements.
• SIF AGC for gain controlled SIF amplifier; single reference QSS mixer able to operate in high performance single reference QSS mode and in intercarrier mode, switchable via I C-bus • AM demodulator without extra reference circuit • Alignment-free selective FM-PLL demodulator with high linearity and low noise •...
14.AK45 CHASSIS PRODUCTION SERVICE MODE ADJUSTMENTS 14.1.SERVICE MENU All system, geometry and white balance alignments are performed in production service mode. Before starting the production mode alignments, make sure that all manual adjustments are done correctly. To start production mode alignments enter the MAIN MENU and then press the digits 4, 7, 2 and 5 respectively or press MUTE and INFO buttons at the same time.
Page 23
Y-Delay SECAM Enter a SECAM B/G colour and black-white bar test pattern via RF. Adjust Y-Delay SECAM till the colour transients on the colour bar of the pattern become as sharper and colours between transients do not mix with each other as possible. Y-Delay NTSC Enter an NTSC colour and black-white bar test pattern via RF.
Page 24
The amplitude of R of RGB output can be adjusted with the drive parameter WDR. The amplitude of G of RGB output can be adjusted with the drive parameter WDG. The amplitude of B of RGB output can be adjusted with the drive parameter WDB. The DC offset values of R of RGB output can be adjusted with the cutoff parameter CR.
Page 25
PANORAMIC VERT_POS (Panoramic mode Vertical Position) It’s used to adjust the vertical position of panoramic mode. PANORAMIC VERT_AMPL (Panoramic mode Vertical Amplitude) It’s used to adjust the vertical amplitude of panoramic mode. PANORAMIC VERT_SCOR (Panoramic mode Vertical S-Correction) It’s used to adjust the vertical s-correction of panoramic mode. PANORAMIC VERT_SSYM (Panoramic mode Vertical S-Symmetry) It’s used to adjust the vertical s-symmetry of panoramic mode.
Page 26
16:9 ZOOM VERT_POS (16:9 Zoom mode Vertical Position) It’s used to adjust the vertical position of 16:9 zoom mode. 16:9 ZOOM VERT_AMPL (16:9 Zoom mode Vertical Amplitude) It’s used to adjust the vertical amplitude of 16:9 zoom mode. 16:9 ZOOM VERT_SCOR (16:9 Zoom mode Vertical S-Correction) It’s used to adjust the vertical s-correction of 16:9 zoom mode.
Page 27
OSD Position It’s used to adjust the horizontal position of the OSD. BCLTHR Beam current threshold BCLG Beam current loop gain ROTATION (TILT) This adjustment only works when the TV has rotation option. Change TILT by pressing Left/Right buttons to rotate the complete raster clock-wise and counter clock-wise depending on the CRT. Check and readjust TRPEZ item if the adjustment becomes improper after some other geometric adjustments are done.
Page 28
POFS2 (RGB HORIZONTAL SHIFT) It’s used to adjust the horizontal position of RGB signal. REFERENCE WDR RED COOL The amplitude of R of RGB output can be adjusted with the drive parameter WDR for the colour temp of cool mode. REFERENCE WDR GREEN COOL The amplitude of G of RGB output can be adjusted with the drive parameter WDR for the colour temp of cool mode.
Page 29
FULL HORZ_POS It’s used to adjust the horizontal position of 16:9 mode (full mode). FULL HORZ_AMPL It’s used to adjust the horizontal amplitude of 16:9 mode (full mode). BRIGHT MODE BRIGHTNESS It’s used to adjust the brightness value of bright mode. BRIGHT MODE COLOUR It’s used to adjust the colour value of bright mode.
Page 30
14:9 RGB CUSHION It’s used to adjust the cushion in 14:9 mode for RGB signals. PANAROMIC RGB HORIZONTAL AMPLITUDE It’s used to adjust the horizontal amplitude in panoramic mode for RGB signals. 16:9 RGB HORIZANTOL AMPLITUDE It’s used to adjust the horizontal amplitude in 16:9 mode for RGB signals. 16:9 SUBTITLE RGB HORIZONTAL AMPLITUDE It’s used to adjust the horizontal amplitude in 16:9 subtitle mode for RGB signals.
Page 31
ADJUST EXPLANATION 2835 2835W MULTI MULTI - PAL I White Point RED White Point GREEN Whit Point BLUE AGC (Automatic Gain Control) It will be adjusted to below 1V of Max. AGC for each TV. IF-PLL Negative IF-PLL Positive Y-Delay Y-Delay SECAM Y-Delay NTSC Y-Delay OTHER...
Page 33
STANDARD MODE COLOUR STANDARD MODE CONTRAST FULL VERT_POS (16:9 MODE) FULL VERT_AMPL FULL VERT_SCOR FULL VERT_SSYM FULL TRAPEZE FULL CUSHION FULL HOR_COR_SYM FULL HOR_CORNER FULL HORZ_POS FULL HORZ_AMPL BRIGHT MODE BRIGHTNESS BRIGHT MODE COLOUR BRIGHT MODE CONTRAST SOFT MODE BRIGHTNESS SOFT MODE COLOUR SOFT MODE CONTRAST PERSONAL MODE FACTORY SETTING BRIGHTNESS...
14.3.OPTIONS MENU Select the parameter by pressing up/down buttons. Adjust the parameter by pressing Left/Right buttons. . In OPTIONS menu, some of the changed parameters are not stored automatically. To store the adjusted parameters, you should turn off and on TV. OPTIONS...
B4: x B3: x B2: x B1: LUMA 1 Luma Soft Limiter Enabled B0: BB 1 Blue Background Option Option 3. (0x19) Video Processor Cathode Drive Level B7: x B6: x B5: x B4: x B3: x B2: x B1: x B0: country = note 0 Note 0: choice for others country option...
note 1: :Frequency Mode Frequency Menu Item available Frequency Menu Item not available Option 8. IF Frequency B7: x B6: x B5: IfI note 3 B4: IfD note 4 B3: IfM note 5 B2: Aps note 6 B1: Hp note 7 B0: Hue note 8 note 3:...
note 3 : RGB Menu Item active/inactive RGB Menu Item inactive RGB Menu Item active note 4 : Equalizer available Equalizer not available Equalizer available note 5 : List Mode available List Mode not available List Mode available note 6 : Country Line available / Aps available or not Country Line not available / Aps not available Country Line available / Aps available...
Option 55. Speaker Setup b7 b6 b5 b4 b3 b2 b1 b0 Speaker Setup (L/R, L/C/R, L/R/S, L/C/R/S) 0 0 0 0 0 0 0 0 Option 56. Audio Options Available Or Not Attention: All bits on the Option 56 must be the “0” for MONO TV SETS B7: nicam note 7 B6: ASD...
14.4.OPTION TABLE RECOMMENDED VALUES X listed in the option can be 0 or 1 OPTION 2835 MULTI 2835W MULTI 2835W PAL I X2 XXXXXX10 X2 XXXXXX10 X2 XXXXXX10 XX XXXXXXXX XX XXXXXXXX XX XXXXXXXX 23 001XXX11 23 001XXX11 001XXX11 XX XXXXXXX0 XX XXXXXXX0 XX XXXXXXX0 XX XXXXXXXX...
14.5.SCREEN ADJUSTMENT (FBT SCREEN) SCREEN ADJUST From the option list change option 2 bit 6 from 0 to 1 for disabling vertical scan. Adjust horizontal line via screen adjust pot. as thin as possible. Then press 0 to leave service menu. AK45 Service Manual 01/12/2003...
BILL OF MATERIAL LIST 2845W*TEAC TEAC 10023315 EU2845ST(AK45)SILVER BOM Date : 28/11/2003 COMPONENT MATERIAL POSITION NUMBER CODE ON/OFF AS.110°(32- 20036465 33")(2.2/AU)(W/MAKARON 30002174 SWITCH SAFE ON/OFF 4A/64A 30002368 CNAS 2P/650 AC MAINS W/C POWER CORD 2.2MT W/FILTER 30014059 AUST.TYPE SWITCH INSULATION DOOR...
Page 68
C751 301 30012589 CAP SMD 4.7NF 50V K (0603) C296 C308 302 30012603 CAP SMD 100NF 25V K R (0603) C362 303 30012607 CAP SMD 150PF 50V J (0603) C287 C304 304 30012650 RES SMD 1/16W 15K J (0603) R528 305 30012657 RES SMD 1/16W 1K J (0603) R718...
Page 69
364 30000792 RES CF 1/4W 75R J R221 R231 365 30000848 RES MF 1/4W 1K F R652 366 30000872 RES MF 1/4W 120K F R630 367 30000880 RES MF 1/4W 130K F R133 368 30000896 RES MF 1/4W 160K G R101 369 30000982 RES MF 1/4W 4.7K J...
Page 70
C253 C739 C524 C286 C357 C506 C720 C508 C724 C522 C523 C525 C358 401 30000352 CAP EL 100UF 16V M C700 C754 C226 402 30000362 CAP EL 1UF 50V M C789 C791 C165 C164 403 30000367 CAP EL 1UF 250V M C137 C619 404 30000371...
Page 73
493 30014465 RES SMD 1/16W 2.7K F (603) R632 494 30016126 CAP SMD 220NF 16V K R (0603) C628 C255 495 30016654 CAP SMD 100NF 16V K R (0603) C269 C270 C271 C274 C275 C276 C352 496 30016654 CAP SMD 100NF 16V K R (0603) C147 C516 C716...