Specifications - Yamaha RX-V495 Service Manual

RX-V495/RX-V495RDS/HTR-5140/HTR-5140RDS

SPECIFICATIONS

AUDIO SECTION
Minimum RMS Output Power Per Channel
MAIN L/R, REAR L/R
20Hz to 20kHz, 0.04% THD, 8Ω
1kHz, 0.07% THD, 8Ω
CENTER
20Hz to 20kHz, 0.04% THD, 8Ω
1kHz, 0.07% THD, 8Ω
Maximum Power (EIAJ)
R, T models only
MAIN L/R, REAR L/R
1kHz, 10% THD, 8Ω
CENTER, 1kHz, 10% THD, 8Ω
Dynamic Power Per Channel (IHF)
MAIN L/R
8/6/4/2Ω
80W+80W/100W+100W/120W+120W/145W+145W
DIN Standard Output Power Per Channel
G model only
MAIN L/R, 1kHz, 0.7% THD, 4Ω
Dynamic Headroom(8Ω)
U, C models only
IEC Power
G model only
MAIN L/R, 1kHz, 0.04% THD, 8Ω
Power Band Width
MAIN L/R, 0.1% THD, 30W, 8Ω
Damping Factor (SPEAKER A)
MAIN L/R, 20Hz to 20kHz, 8Ω
Input Sensitivity/Input Impedance
PHONO (MM)
CD etc.
MAIN L/R (EXTERNAL DECODER)
CENTER
SURROUND L/R
SUB WOOFER
Maximum Input Signal Level (1kHz)
PHONO (MM), 0.1% THD
CD etc. (EFFECT ON), 0.5% THD
Output Level/Output Impedance
REC OUT
SUB WOOFER (MAIN SP : SMALL)
Headphone Jack Rated Output/Impedance
CD etc., Input=1kHz, 150mV, RL=8Ω
Frequency Response(20Hz to 20kHz)
CD etc., MAIN
RIAA Equalization Deviation
PHONO (MM)
Total Harmonic Distortion(20Hz to 20kHz)
PHONO (MM) to REC OUT (1V)
CD etc.(EFFECT OFF) to MAIN SP OUT(30W/8Ω)
Signal-to-Noise Ratio(IHF-A Network)
PHONO (MM), Input 5mV shorted, REC OUT
U, C, R, T models
A, B, G, L models
CD etc,(EFFECT OFF), Input 150mV shorted, SP OUT
5
(Power Amp. Section)
60W+60W
70W+70W
60W
70W
95W+95W
95W
100W+100W
1.55dB
65W+65W
10Hz to 50kHz
60
2.5mV/47kΩ
150mV/47kΩ
150mV/47kΩ
150mV/40kΩ
150mV/40kΩ
150mV/40kΩ
100mV
2.2V
150mV/1.2kΩ
4V/1.2KΩ
0.4V/390Ω
0±0.5dB
0±0.5dB
0.02%
0.025%
86dB
81dB
96dB
Residual Noise(IHF-ANetwork)
MAIN L/R, SP OUT
Channel Separation(Vol. –30dB, EFFECT OFF)
PHONO, Input shorted, 1kHz/10kHz
CD etc, Input 5.1kΩ terminated, 1kHz/10kHz
Tone Control Characteristics
BASS : Boost/Cut
: Turnover Frequency
TREBLE : Boost/Cut
: Turnover Frequency
Filter Characteristics
MAIN, REAR SP SMALL : H.P.F.
SUB WOOFER : L.P.F.
FM SECTION
Tuning Range
U, C models
R, T models (Frequency Step: 100kHz)
(Frequency Step: 50kHz)
A, B, G, L models
50dB Quieting Sensitivity (IHF)
U, C, R, T models only
Mono, 1kHz, 100% mod
Stereo, 1kHz, 100% mod
Usable Sensitivity (DIN)
A, B, G, L models only
DIN, Mono(S/N 26dB)
DIN, Stereo(S/N 46dB)
Alternate Channel Selectivity
U, C, R, T models (±400kHz)
A, B, G, L models (±300kHz)
Selectivity(two signals, 40kHz Dev.)
Signal-to-Noise Ratio
U, C, R, T models (IHF)
Mono/Stereo
A, B, G, L models (DIN-Weighted, 40kHz Dev.)
Mono/Stereo
Harmonic Distortion (1kHz)
Mono/Stereo
Stereo Separation (1kHz)
Frequency Response (20Hz to 15kHz)
Output Level (1kHz)
U, C, R, T models (100% mod.)
A, B, G, L models (40kHz Dev.)
Antenna Input
AM SECTION
Tuning Range
U, C models
R, T models (Frequency Step : 10kHz)
(Frequency Step : 9kHz)
A, B, G, L models
Usable Sensitivity
Signal-to-Noise Ratio
Output Level (1kHz, 30% mod.)
Antenna
150µV
60dB/55dB
60dB/45dB
±10dB(50Hz)
350Hz
±10dB(20kHz)
3.5kHz
fc=90Hz, 12dB/oct.
fc=90Hz, 18dB/oct.
87.5 to 107.9MHz
87.5 to 108.0MHz
87.50 to 108.00MHz
87.50 to 108.00MHz
1.6µV(15.3dBf)
23µV(38.5dBf)
0.9µV
28µV
75dB
55dB
81dB/75dB
75dB/69dB
0.1%/0.2%
48dB
0±1dB
550mV
550mV
75Ω unbalanced
530 to 1710kHz
530 to 1710kHz
531 to 1611kHz
531 to 1611kHz
300µV/m
52dB
150mV
Loop antenna