Q42647-0 Output Module - Crown Micro-Tech MT-600 Service Manual

Q42647-0 Output Module (P10137-1 board) Parts List
CAPACITORS
C01 C 3978-1
C02 C 6804-6
C03 C 6804-6
C04 C 3996-3
C05 C 6807-9
C06 C 6806-1
C07 C 6807-9
C08 C 6809-5
C09 C 6810-3
DIODES
D01 C 2851-1
D02 C 2851-1
D03 C 2851-1
D04 C 2851-1
D05 C 2851-1
D06 C 2851-1
D07 C 2851-1
D08 C 2851-1
D09 C 2851-1
D10 C 2851-1
D11 C 2851-1
D12 C 2851-1
INDUCTORS
L00 C 6592-6
L01 C 3510-2
L02 C 3510-2
TRANSISTORS
Q17 C 3810-6
Q19 C 3578-9
RESISTORS
R00 A10266-7501
R01 A10266-4711
R02 C 7778-1
R03 C 6486-2
R04 C 6486-2
R06 C 6486-2
R07 C 6486-2
R09 C 7779-9
R10 A10266-4711
R11 A10266-2R73
R12 A10266-2R73
R13 A10266-7501
R14 A10266-2R73
R16 C 6486-2
R17 C 6486-2
R19 C 6486-2
Micro-Tech 600 Amplifier Service Manual
R20
R21
.047µF
R22
.1µF
R23
.1µF
R24
.0047µF
R25
.001µF
R26
.01µF
R27
.001µF
R28
220pF
R30*
180pF
MISC
Board
1N4004
Jumpers
1N4004
Clips
1N4004
J500
1N4004
1N4004
Note: R30 is 102 Ohms in most units, though in
1N4004
some cases a different value may be used to match
1N4004
the installed S100/S200 LM334 (C5826-0) device
1N4004
grade. This is the standard value and is used with
1N4004
the most common LM334 grade, green. If the
1N4004
LM334 is marked with a blue dot, R30 should be a
1N4004
107 Ohm resistor (A10265-10701); if it is marked
1N4004
with a yellow dot then R30 should be a 100 Ohm
resistor (A10265-10001).
Output Coil
470µH
470µH
MPSA43
MPSA93
75
470
5.6 FP
.2 5W
.2 5W
.2 5W
.2 5W
22 FP
470
2.7 1W
2.7 1W
75
2.7 1W
.2 5W
.2 5W
.2 5W
C 6486-2
C 7778-1
C 7779-9
C 6844-2
A10266-1331
A10266-2221
C 6844-2
A10266-3911
A10266-1331
A10265-10201*
P10137-1
C 5868-2
D 6414-3
J600 C 7057-0
.2 5W
5.6 FP
22 FP
250 Pot
13K
2.2K
250 Pot
390
13K
102*
0 Ohm (8)
Q17/Q19
10 Pin HDR
23