Download Table of Contents Print this page

Kenwood CK 440 FFD Instructions For Use Manual

Dual fuel double oven cooker installation advice

Advertisement

DUAL FUEL
DOUBLE OVEN COOKER
CK 440 FFD
Instructions for use - Installation advice
IE

Advertisement

loading

Related Manuals for Kenwood CK 440 FFD

No related manuals

Summary of Contents for Kenwood CK 440 FFD

  • Page 1 DUAL FUEL DOUBLE OVEN COOKER CK 440 FFD Instructions for use - Installation advice...
  • Page 3: Table Of Contents

    CONTENTS Page Number Introduction ........4 Important Safeguards &...
  • Page 4: Introduction

    Dear Customer, Thank you for purchasing a Kenwood Dual Fuel Double Oven Cooker The safety precautions and recommendations in these instructions are for your own safety and that of others. They will also provide a means by which to make full use of the features offered by your appliance.
  • Page 5: Important Safeguards & Recommendations

    IMPORTANT SAFEGUARDS WARNING AND RECOMMENDATIONS When correctly installed, your product meets all safety requirements laid down for this type of product catego- After unpacking the appliance, check to ry. However special care should be ensure that it is not damaged and that taken around the rear or the under- the oven door closes correctly.
  • Page 6: Cooking Hob

    1 - COOKING HOB Fig. 1.1 COOKING HOB 1. Triple-ring burner (TR) 3,50 kW 2. Semi-rapid burner (SR) 1,75 kW 3. Rapid burner (R) 3,00 kW 4. Auxiliary burner (A) 1,00 kW 5. Semi-rapid burner (SR) 1,75 kW 6. Auxiliary burner (A) 1,00 kW Important Note: The electric ignition is incorporated in the knobs.
  • Page 7: Control Panel

    2 - CONTROL PANEL Fig. 2.1 CONTROL PANEL - Controls description 1. Front right burner control knob 2. Rear right burner control knob 3. Rear central burner control knob 4. Front central burner control knob 5. Rear left burner control knob 6.
  • Page 8: Use Of Cooking Hob

    3 - USE OF COOKING HOB GAS BURNERS Each burner is controlled by a gas tap which opens and closes the gas supply. Line the control knob symbol up with the indicator on the control panel (fig. 3.1) to obtain: –...
  • Page 9 LIGHTING GAS BURNERS FITTED CHOICE OF THE BURNER WITH SAFETY VALVE DEVICE On the control panel, near each knob, there is a diagram that indicates which To ignite the burner, the following burner is controlled by that knob. instructions are to be followed: Select the burner that is most suitable 1) Press in the corresponding knob and for the diameter and capacity of the pan...
  • Page 10 AIR FLOW AIR FLOW AIR FLOW (cooling fan) (cooling fan) (cooling fan) CORRECT USE OF RAPID BURNER Fig. 3.4 CORRECT USE OF TRIPLE-RING BURNER (Fig. 3.5a - 3.5b) Flat-bottomed pans should be placed directly onto the pan-support. When using a WOK always place the supplied stand in position over the burner to main- tain the correct operation of the triple-ring burner (Fig.
  • Page 11: Multi-Function Main Oven

    4 - MULTI-FUNCTION MAIN OVEN OPERATING PRINCIPLES Attention: the oven door becomes Heating and cooking in the MULTI- very hot during operation. FUNCTION oven are obtained in the fol- Keep children away. lowing ways: a. by normal convection The heat is produced by the upper and GENERAL FEATURES lower heating elements.
  • Page 12 Fig. 4.1 Fig. 4.2 TEMPERATURE KNOB (fig. 4.1) To turn on the heating elements of the oven, set the switch knob on the desired program and select the required temperature. To set the temperature, line up the temperature knob indicator with the required tempera- ture.
  • Page 13 GRILLING The infra-red heating element is switched on. The heat is diffused by radiation. Use with the oven door closed and the temperature knob between 50° and 250°C for a maximum of 15 minutes. Note: It is recommended that you do not grill for longer than 30 minutes at any one time.
  • Page 14 VENTILATED GRILL COOKING The infra-red ray grill and the fan are on. The heat is mainly diffused by radiation and the fan then distributes it throughout the oven. The temperature must be set between 50° and 175 °C for max 30 minutes. It is necessary to preheat the oven for about 5 minutes. Use with the oven door closed.
  • Page 15 COOKING ADVICE GRILLING AND “AU GRATIN” Set the switch to position Set the temperature knob to 175 °C and OVEN COOKING after having preheated the oven, simply Before introducing the food, preheat the place the food on the shelf. oven to the desired temperature. Close the door and let the oven operate For a correct preheating operation, it is until grilling is complete.
  • Page 16: Conventional Oven

    5 - CONVENTIONAL OVEN Attention: the oven door becomes very hot during operation. Keep children away. GENERAL FEATURES NOTE: Upon first use, it is advisable to operate The conventional oven has 3 heating the oven for 30 minutes in the position elements which are: and for another 30 minutes at the –...
  • Page 17 Fig. 5.1 Fig. 5.2 TEMPERATURE KNOB FUNCTION SELECTOR KNOB (Fig. 5.2) (fig. 5.1) This only sets the cooking temperature and does not switch the oven on. Rotate the knob clockwise to set the Rotate clockwise until the required tempera- oven for one of the following func- ture is reached (from 50 to 250°C).
  • Page 18 TRADITIONAL CONVECTION COOKING This function can also be used for traditional convection cooking: the temperature knob must be regulated between 50 and 250°C. It is necessary to preheat the oven before introducing the foods to be cooked. Traditional convection cooking recommended use: For foods which require the same cooking temperature both internally and externally, i.e.
  • Page 19 USE OF SPECIAL DISH RACK USING THE SPECIAL RACK FOR NORMAL COOKING This special shelf can be used as a dish rack or when turned over, as a normal Slide in the shelf on the guides: the shelf for oven cooking. safety catch must be turned toward the oven base (see detail of figure 5.4).
  • Page 20: Cooking Guide

    6 - COOKING GUIDE Temperature and times given are approximate, as they will vary depending on the quality and amount of food being cooked. Remember to use ovenproof dishes and to adjust the oven temperature during cooking if necessary. COOKING CHART Temperature Food Cooking Time (approx)
  • Page 21: Electronic Programmer (Main Oven Only)

    7 - ELECTRONIC PROGRAMMER (Main oven only) Description of the illuminated If you use the oven for none auto- symbols: matic or semi-automatic cooking, ensure programmer is set to man- AUTO - flashing - Programmer in auto- ual position by pushing button.
  • Page 22 ELECTRONIC CLOCK ELECTRONIC TIMER (fig. 7.2) The programmer is equipped with an The timer program consists only of a electronic clock with an illuminated dis- buzzer which may be set for a maximum play which indicates hours and minutes. period of 23 hours and 59 minutes. Upon immediate connection of the oven If the AUTO is flashing push the but-...
  • Page 23 AUTOMATIC OVEN COOKING 3. Set the temperature and the cooking program (see the relevant sections). To cook food automatically in the oven, it is necessary to: Once the oven is programmed it will 1. Set the length of the cooking time switch on automatically at the right time 2.
  • Page 24 At the end of the cooking, the oven and SEMI - AUTOMATIC COOKING symbol will turn off, the AUTO will This is used to switch the oven off auto- flash and a buzzer will go off which can matically after the desired cooking time be stopped by pushing any of the but- has elapsed.
  • Page 25: Cleaning & Maintenance

    8 - CLEANING AND MAINTENANCE STAINLESS STEEL SURFACES Important: (COATED) Before cleaning or carrying out any maintenance disconnect the The stainless steel front panels on this appliance from the electrical sup- cooker (facia, oven door, storage ply and wait for it to cool down. compartment) are protected by a finger- print proof lacquer.
  • Page 26 GAS TAPS CORRECT REPLACEMENT OF THE BURNERS In the event of operating faults in the gas taps, call the After Sales Service It is very important to check that the Department. burner flame distributor F and the cap C has been correctly positioned (see fig. 8.1 - 8.2) - failure to do so can cause BURNERS serious problems.
  • Page 27 TRIPLE RING BURNER The triple ring burner must be correctly positioned (see fig. 8.3); the burner rib must be enter in their logement as shown by the arrow. The burners must be correctly positioned so that they cannot rotate (fig. 8.4). Then position the cap A and the ring B (fig.
  • Page 28 Fig. 8.6 OVEN DOOR STORAGE COMPARTMENT The storage compartment is accessible The internal glass panel can be easily through the pivoting panel (fig. 8.7). removed for cleaning by unscrewing the 2 retaining screws (Fig. 8.6) Do not store flammable material in the oven or in the storage com- partment.
  • Page 29 INSIDE OF OVEN This must be cleaned after every use. Remove and refit the side runner frames as described on the next chapter. With the oven warm, wipe the inside walls with a cloth soaked in very hot soapy water or another suitable product. Side runner frames, tray and rack can be removed and washed.
  • Page 30 REMOVING THE OVEN DOOR Fig. 8.10A The oven door can easily be removed as follows: – Open the door to the full extent (fig. 8.10A). – Attach the retaining rings to the hooks on the left and right hinges (fig. 8.10B). –...
  • Page 31: Advice For The Installer

    Advice for the installer IMPORTANT – Cooker installation and maintenance must only be carried out by QUALIFIED TECHNI- CIANS and in compliance with the local safety standards. Failure to observe this rule will invalidate the warranty. – The electrical mains outlet, if located behind the cooker, must not be higher than 18 cm above the floor level.
  • Page 32: Installation

    9 - INSTALLATION This cooker has class “2/1” overheating protection so that it can be installed next to a cabinet. If the cooker is installed adjacent to furniture which is higher than the gas hob cooktop, a gap of at least 50 mm must be left between the side of the cooker and the furniture. The furniture walls adjacent to the cooker must be made of material resistant to heat.
  • Page 33 FITTING THE ADJUSTABLE FEET The adjustable feet must be fitted to the base of the cooker before use. Rest the rear of the cooker on a piece of the polystyrene packag- ing exposing the base for the fit- ting of the feet. Fit the 4 legs by screwing them tight into the support base as Fig.
  • Page 34 MOVING THE COOKER WARNING When raising cooker to upright posi- tion always ensure two people carry out this manoeuvre to prevent dam- age to the adjustable feet (fig. 9.5). WARNING Be careful: do not lift the cooker by the door handle when raising to the upright position (fig.
  • Page 35 INSTALLATION OF BASE SKIRTING Fig. 9.14 Fig. 9.8 Fig. 9.9 The base skirting assembly kit comprises: - 2 long panels (front and rear) - 2 lateral panels - 8 feet - 1 central rear bracket - 1 clip for bracket fixture to panel - 9 self-tapping screws SKIRTING ASSEMBLY INSTRUCTIONS •...
  • Page 36 • Join the rear panel R to the right and left panels as shown in fig. 9.12. • Remove screw V located at the rear of the cooker (fig. 9.10). • Fix central bracket S between clip C on the panel and the cooker, and re-fit screw V (fig.
  • Page 37 BACKGUARD – Remove the two spacers “A” and the screw “B” from the rear of the cooker top. – Assemble the backguard as shown in figure 8.8 and fix it by screwing the central screw “B” and the spacers “A”. Fig.
  • Page 38 PROVISION FOR VENTILATION The room containing the cooker should have an air supply in accordance with BS.5540: Part 2: 1989. All rooms require an openable window or equivalent while some rooms require a permanent vent in addition to the openable window. The cooker should not be installed in a bed-sitting room, of volume less than 21 m Where a DOMESTIC COOKER is installed in a room or internal space, that room or internal space shall be provided with a permanent opening which communicates directly...
  • Page 39: Gas Section

    10 - GAS SECTION GAS INSTALLATION GAS CONNECTION IMPORTANT NOTE The installation of the cooker to Natural Gas or LP Gas must be carried out by a This appliance is supplied for use on qualified gas engineer. Installers shall NATURAL GAS only and cannot be take due account of the provisions of the used on any other gas without modifica- relevant British Standards Code of...
  • Page 40 GAS CONNECTION The gas supply must use the nearest gas inlet pipe which is located at the left or the right hand side at the rear of the appliance (fig. 10.1). The unused end inlet pipe must be closed with the plug interposing the gasket. Flexible hoses can be used where the sited ambient temperature of the hose does not exceed 70°C.
  • Page 41 To avoid damage to the appliance gas rail inlet pipe the fittings should be tightened using two suitable spanners (fig. 10.2). After connection to the mains gas supply the couplings should be checked for gas soundness/tightness as per current regulations for the gas type being used Fig.
  • Page 42 CONVERSION TO LPG 1 - Injectors replacement of top burners If the injectors are not supplied they can be obtained from the “Service Centre”. The diameter is marked on the injector in cents of millimetre. Select the injectors to be replaced according to the “Table for the choice of the injectors”...
  • Page 43 TABLE FOR THE CHOICE OF THE INJECTORS Cat: 2H3+ G 30 - 28-30 mbar G 20 Nominal Reduced BURNERS G 31 - 37 mbar 20 mbar Power Power By-pass Ø injector By-pass Ø injector [kW] [kW] [1/100 mm] [1/100 mm] [1/100 mm] [1/100 mm] 1,00...
  • Page 44: Electrical Section

    11 - ELECTRICAL SECTION N.B. For connection to the mains, do not use adapters, reducers or IMPORTANT: The cooker must be branching devices as they can cause installed in accordance with the overheating and burning. manufacturer’s instructions. Incorrect installation, for which the If the installation requires alterations to manufacturer accepts no responsi- the domestic electrical system or if the...
  • Page 45 TECHNICAL DATA ELECTRICAL FEEDER CABLE CONNECTION 230 V AC - 50 Hz To connect the supply cable: Multi-function Main oven - Remove the screws securing the – Bottom element 1.40 kW cover “A” on the rear of the cooker – Top element 1.00 kW (fig.
  • Page 46: Guarantee

    GUARANTEE UK only If your appliance goes wrong within one year from the date you bought it, we will repair it (or replace it if necessary) free of charge provided: • you have not misused, neglected, or damaged it; • it has not been modified; •...
  • Page 47: After Sales Service

    AFTER SALES SERVICE If you require After Sales Service contact the MASTERCARE Domestic Appliance Helpline Telephone 08701 565550. Ser. Nr. Descriptions and illustrations in this booklet are given as simply indicative. The manufacturer reserves the right, considering the characteristics of the models described here, at any time and without notice, to make eventual necessary modifications for their construction or for commercial needs.
  • Page 48 code 1102761 ß1 Part Number 57706...