· Do Not Use or Store Outdoors. · Do Not Use Bleach in the Mopit Before using the Mopit mini you need to fill it with water and cleaning solution. Filling The Fresh Wa- ter Tank This is where you fill the Mopit with water.
To adjust the handle bar height simply lift up the handle bar quick re- lease lever, adjust the handle, and then push the quick release lever back down. You can also use the Mopit mini with the quick release handle disengaged for quick height ad- justment when going under tables and obstacles.
Page 6 BASIC OPERATION Draining The Dirty Water It is important to drain the dirty water tank after each use. If dirty water sits in your dirty water tank for an extended period of time, your ma- chine will start to stink. Simply remove the drain hose cap and let the drain hose down onto a floor drain or into a bucket.
Page 7 BASIC OPERATION Water Valve The water control valve controls how much water goes onto the floor. The water valve is full on when the black valve handle is horizontal, and full off when the handle is vertical. To lower water output, position the valve between full on and full off.
Page 8 MAINTENANCE / SERVICE Cleaning The Water Filter When you are not getting enough water onto the floor, clean the water filter. Before you clean the fresh water filter make sure that the water valve is turned off (see page 7) Tip the Mopit on its back, pull filter out of its clip, pull off the water lines, twist the filter housing apart and remove and rinse out the filter.
Page 9
Page 9 MAINTENANCE / SERVICE Changing The Squeegee Blade On average the squeegee blade will need to be changed every 2-6 weeks. If the machine is leaving streaks, and not picking up all of the water, or the Mopit is not cleaning very well, check your squeegee blade for wear.
Page 10
Page 10 MAINTENANCE / SERVICE Adjusting The Brush Pressure WARNING: Adjusting the brush too low can damage the brush motor and lessen the cleaning performance. As the scrub brush wears, your brush pressure on the floor will de- crease. To com- pensate for brush wear, adjust the...
Page 11
Page 11 MAINTENANCE / SERVICE Belt Replacement And Tensioning Tip the Mopit on its back Remove belt cover by removing two Allen screws with on-board 5/32 tool Loosen these two 1/8” Allen screws. With a 3/16” Allen wrench twist the belt tensioning screw counter clockwise.
Page 12
Page 12 MAINTENANCE / SERVICE Brush Replacement The Mopit mini scrub brush is very durable and should last at least one year. As the brush wears it can be lowered by following the in- structions on page 10. For replacement follow the steps below.
Page 13
Let the tank sit with the clean out cap and drain hose cap off until the inside of the recovery tank is dry. If your machine still has a foul odor order some Mopit deodoriz- er from Spectrum.
Page 14
Page 14 MAINTENANCE / SERVICE Replacing The Battery Pack A properly cared for lithium battery pack should last for about 2000 charging cycles. IMPORTANT: It is critical that the batteries be replaced with 24Volt LiFePo4 Lithium batteries. 1-Make sure all of the switches are off and Remove the 4 switch plate screws 2.
Page 15
Page 15 MAINTENANCE / SERVICE Brush Motor Replacement On rare occasions the brush motor may need to be replaced. Please call Spec- trum at 1-800-290-2833 to troubleshoot and see if your brush motor needs to be replaced. The brush motor is equipped with an automatic thermal circuit breaker.
Page 16 MAINTENANCE / SERVICE Battery Charger Replacement If the power light does not come on when plugged in, or if the batteries are not accepting a charge, the charger may need to be replaced. To replace, remove the thumb screw, lift the hinged cover, disconnect electrical and pull charger free.
Page 17
Page 17 MAINTENANCE / SERVICE Replacing Water Solenoid Turn off the manual wa- ter valve Disconnect the solenoid electrical quick discon- nect Remove the two Sole- noid mounting screws with the on-board 5/32 allen tool Press in the two hose retaining clips and pull out the two hoses To replace follow the above steps in reverse...
Drive Bearing Replace- ment Follow the instructions on pages 11 and 15 for removing the brush and brush motor Pull off the bearing plate, and replace with a new bearing plate assembly from spectrum See exploded view on page 31...
Check to make sure that the charger power cord is plugged into the charger and is in good condition and that your power outlet is working. Call Spectrum for troubleshooting. Also see page 16 on charger replace- ment. Mopit Is Leaving Black Marks The most common cause is not getting water onto the floor.
Page 20
7 (Squeegee pedal) Battery Charge: If your battery is weak you won’t have much suc- tion or scrubbing power. See pg 6 and pg 19 on battery charging For more help call Spectrum 1-800-290-2833...
Page 21
Page 21 TROUBLESHOOTING My Mopit Is Not Picking Up Water If the Mopit is not picking up water, there is an issue with the water recov- ery system. Here are the things to check: 1. Check the squeegee blades for wear and replace if necessary (pg 9) 2.