Hoover HVEF 742 Instructions For Use And Installation page 8

• STOPPING A COOKING ZONE
- Press the selection button of the required cooking zone.
- Press the "-" button to display heat level '0' . Now the zone goes
off, the indicator '0' goes off after 10 seconds.
- To stop rapidly, press the "-" and "+" buttons at the same time.
The heat level automatically goes down to '0'.
The cooking zone goes off.
• GENERAL STOP
The cooking zones and the timer can be stopped at any
moment by pressing the On-Off button.
• RESIDUAL HEAT INDICATOR
The control panel tells the user when the surface temperature of
the cooking zones exceeds about 60°C, by the following displaying:
. When the temperature goes back below 60°C, the 'H ' display
goes off.
For ending the cooking, we advise switching off the cooking zone
and using the residual heat of the zone to finish cooking gently.
N.B. After a cut in the current, the residual heat indicator disappears
completely, even if the surface temperature exceeds 60°C.
• OPERATING THE ADDITIONAL COOKING ZONE
(TWO ZONES)
The cooking zone with two zones is fitted certain models.
• TO START THE ADDITIONAL COOKING ZONE:
- Press the button .
In the next 10 seconds,
- Press the button for the zone with the addition. In the display
zone, the blinking lamp goes steady. It shows that the zone is live.
- Select a heat level between 1 and 9.
- Press the button to start the additional zone.
• TO STOP THE ADDITIONAL ZONE:
- The cooking zone with addition must be live: in the display zone,
the lamp must be on. If not, select the relevant zone again.
- Press the button . The display LED for the additional zone
disappears. The additional cooking zone goes off.
- To rapidly stop the complete cooking zone, press the "+" o "-"
buttons at the same time. The heat level automatically goes down
to "0". The cooking zone goes off.
• PROGRAMMING A COOKING ZONE
Every cooking zone can be programmed for a maximum time of
99 minutes.
- Start the required zone.
The control LED near the heat level must be displayed, it shows
that the zone is live.
- Press the Timer button
The zone mark around the timer display shows the controlled
zone.
- Press the "+" button to select the time in minutes.
This is saved automatically after three seconds.
The programmed time can be modified at any moment by
pressing the timer selection button, the timer control LED must
be on. When the time has run, the cooking zone goes off
automatically and an audible beep sounds for 1 minute. Press
any button to stop it.
The programmed time can be reset to "0" using the "-" button
or pressing the "+" and "-" buttons at the same time, the cooking
zone is then no longer linked to the timer but stays operational. So
you will have to stop the zone independently.
The time can be used alone as reminder, it will ring at the
end of the programmed time.
.
8 GB-IE
• LOCKING BUTTON OPERATION
The locking function holds the current settings, or prevents anyone
from starting the hob. It is also used for cleaning the control strip
as the controls can be locked without the hob being on.
- Press the On/OFF button.
- According to your choice, start or not the cooking zones.
- Press the locking button
button works, except the On/Off button.
The locking indicator lamp comes on.
To release the locking function, just press the locking button ; the
indicator lamp goes off, all the controls work again.
If when the controls are locked, the timer is on, the time will be
counted automatically and the zone switched off at the end of the
programmed time.
If the locking control is on when the hob is finally shut down, the
locking control stays operational and prevents any action when
the hob is restarted. Press the locking button
• FAST HEATER OPERATION
Every cooking zone on the hob is equipped with a fast heater for
raising the cooking zone's temperature faster:
Starting the fast heater :
- Press the On/OFF button.
- Start the required zones, press the "+" button to obtain position
"9", release the button "-" button briefly and press it again ; the
display alternates showing A "Fast heater" and 9 heat level.
- If necessary reduce to the required heat position, the display
alternates showing "A" "fast heater" and the new heat position.
Cooking Power
position released
(%)
0 : 0 %
1 : 3 %
2 : 6 %
3 : 11 %
4 : 16 %
5 : 19 %
6 : 32 %
7 : 45 %
8 : 65 %
9 : 100 %
E.g. 1800 W zone at position 6 = 32% of 1800 W power released
When the "Fast heater" is on, the zone supplies 1800 W power
for 2.5 minutes, and adjusts to 576 W after this time.
* For increased safety, the cooking zones cut off automatically if
they are left on too long. The cut off depends on the heat level
used.
To desactivate the fast heater
- Switch on the cooking zone, press the " - " button to come back
to a normal heat level, decrease to the heat level required or to
" 0 " to stop the cooking zone.
to set the data ; in this way no other
to unlock.
Time of Maximum
fast heater operating
(minutes) time before
automatic
cut off*
: 0 : 0 H
: 1 : 6 H
: 3 : 6 H
: 5 : 5 H
: 6,5 : 5 H
: 8,5 : 4 H
: 2,5 : 1,5 H
: 3,5 : 1,5 H
: 4,5 : 1,5 H
: 0 : 1,5 H