Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fluid Gaming EK-AC GEFORCE RTX 3080/3090 D-RG
Summary of Contents for Fluid Gaming EK-AC GEFORCE RTX 3080/3090 D-RG
- Page 1 EK-AC GEFORCE RTX 3080/3090 D-RGB USER GUIDE...
- Page 2 Before you start using this product, please follow these basic This product is made from aluminum and can be only used guidelines: with other aluminum liquid cooling components, such as Al fittings, water blocks and radiators. Mixing aluminum with Carefully read the manual before beginning with the copper and brass products can cause galvanic corrosion installation process.
-
Page 3: Table Of Contents
TABLE OF CONTENTS BOX CONTENTS WATER BLOCK DIMENSIONS WATER BLOCK SPECIFICATIONS AND MAIN PARTS PREPARING YOUR GRAPHICS CARD REMOVING THE STOCK COOLER CLEANING THE PCB CUTTING AND PLACING THERMAL PADS APPLYING THERMAL COMPOUND INSTALLING THE WATER BLOCK PLACING THE BLOCK ON THE GRAPHICS CARD ATTACHING THE BLOCK TO THE GRAPHICS CARD CHECKING FOR CONTACT INSERTING THE GRAPHICS CARD INTO THE CHASSIS... - Page 4 BOX CONTENTS Universal Mounting Mechanism – You may not need every screw from this package. M2.5x4 AX1 Screw (22 pcs) PVC Washer M2.5 (22 pcs) EK-AC GeForce RTX 3080/3090 D-RGB EK-Loop Multi Allen Key (1 pc) Thermal Grease (1 pc) Thermal Pad F 1.0 mm (4 pcs) EK-Plug G1/4 Acetal (2 pcs) / 4 /...
-
Page 5: Water Block Dimensions
WATER BLOCK DIMENSIONS 234 mm 119.80 mm 19.70 mm 90.80 mm / 5 /... -
Page 6: Water Block Specifications And Main Parts
WATER BLOCK SPECIFICATIONS AND MAIN PARTS Technical Specification: - Dimensions: (LxHxW) – 234x122.4x19.7mm - D-RGB (Adressable RGB) cable length: 500mm - D-RGB LED COUNT: 8 M3 x 10 DIN7991 SCREW - D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground M4 x 8 DIN7991 SCREW M4 x 27 DIN7984 SCREW M4 x 8 DIN7991 TERMINAL... -
Page 7: Preparing Your Graphics Card
PREPARING YOUR GRAPHICS CARD STEP 1 REMOVING THE STOCK COOLER Place your graphics card on the flat surface and carefully remove the stock cooler. Do not forget to unplug all the LED and fan connectors. Pay atten- tion to the following steps in order to install the EK-AC GEFORCE RTX 3080/3090 D-RGB water block onto the graphics card. -
Page 8: Cutting And Placing Thermal Pads
CUTTING AND PLACING THERMAL PADS STEP 1 Your GPU water block comes with thermal pads that have to be cut into smaller pieces to cover all the VRM components, such as COILs, MOSFETs, and drivers. Thermal Pad F – 1.0 mm (120 x 16 mm) You must remove the protective foil from both sides of the thermal pad before installation. -
Page 9: Applying Thermal Compound
APPLYING THERMAL COMPOUND STEP 1 Apply the enclosed EK-TIM Ectotherm thermal grease (thermal compound) on the CPU heat spreader – IHS – as shown in the image. The layer of the thermal compound must be thin and even over the entire surface of the IHS. The excessive or uneven application of thermal grease may lead to poor performance! For this Step, you will need:... -
Page 10: Installing The Water Block
INSTALLING THE WATER BLOCK STEP 1 PLACING THE BLOCK ON THE GRAPHICS CARD This procedure is the same for all full-cover water blocks. Carefully position the water block with preinstalled standoffs on the graphics card. During this process, make sure you have aligned mounting holes of the PCB with holes of the water block (same applies to other tops). -
Page 11: Checking For Contact
CHECKING FOR CONTACT STEP 1 If necessary, temporarily remove the water block to check for uniform sur- face contact between the block and components. Pay special attention to the VRM section of the graphics card. Check whether the water block makes contact with the intended integrated circuit. -
Page 12: Installation Of Fittings And Tubing
INSTALLATION OF FITTINGS AND TUBING STEP 1 Screw-in two (2) G1/4 threaded male fittings. Attach the liquid cooling tubes and connect the water block(s) to the cooling loop. Do not forget to plug the remaining two openings with enclosed EK-Plug G1/4 or its equivalent. EK- PLUG You can use any opening as an inlet/outlet port. -
Page 13: Testing The Loop
TESTING THE LOOP To make sure the installation of EK components was successful, we rec- ommend you perform a 24-hour leak test. When your loop is complete and filled with coolant, connect the pump to a PSU outside of your system. Do not connect power to any of the other components. -
Page 14: Support And Service
SUPPORT AND SERVICE In case you need assistance, please contact: http://support.ekwb.com/ EKWB d.o.o. Pod lipami 18 1218 Komenda Slovenia - EU SOCIAL MEDIA EKWaterBlocks @EKWaterBlocks ekwaterblocks EKWBofficial ekwaterblocks...