Troubleshooting Guide; Guide De Dépannage - Braun TriForce JB 901AN Manual

Table of Contents

Advertisement

Troubleshooting Guide

Problem
Blender does not operate.
Liquid is splashing out of the jug.
Motor base is moving on the countertop.
Error code is shown on the Timer Display
(E01,E02,E03,E04,E05)
Guide de dépannage
Problème
Le blender ne fonctionne pas.
Éclaboussures de liquide hors du pichet.
La base moteur bouge sur le plan de travail.
Le code d'erreur est affiché sur l'affichage
de la minuterie
(E01, E02, E03, E04, E05)
18
Potential causes
No power supply.
Jug or Smoothie2Go attachment is not atta-
ched properly. Timer shows three dashes (- - -)
Gasket is not mounted properly, loose, or even
torn.
Jug lid or measuring cap are not closed
properly.
Jug is overfilled.
Rubber feet are not clean.
E01
Overload protection
E02/E03
The thermal protection is activated to protect
the drive unit from overheating
E04/E05
Causes éventuelles
Pas d'alimentation électrique
Le pichet ou le Smoothie2Go n'est pas correc-
tement fixé. La minuterie affiche trois tirets (- - -)
Le joint n'est pas correctement monté, des-
serré ou même déchiré.
Le couvercle du pichet ou le bouchon doseur ne
sont pas fermés correctement.
Le pichet est trop rempli.
Le pied en caoutchouc est sale.
E01
Protection de surcharge
E02/E03
La protection thermique est activée pour proté-
ger l'unité d'entraînement contre la surchauffe
E04/E05
Solution
Check the fuse/circuit breaker in your home.
If none of the above works, contact Braun
Customer Service
Check the correct position of the attachment.
Ensure that gasket is mounted properly.
Close the lid and measuring cap.
Follow the maximum quantity recommenda-
tion in the processing table.
Clean the rubber feet to ensure a good grip.
Turn the blender off, remove the jug from the
motor unit and check if the blade is blocked.
Follow the recommended speed or mode in
the processing table.
Turn the blender off, unplug and wait at least
20 minutes before resuming operation. If the
error code does not disappear contact Braun
Customer Service.
Turn the blender off and on again. If the error
code does not disappear contact Braun Cus-
tomer Service.
Solution
Vérifiez si l'appareil est branché. Vérifiez le
fusible/disjoncteur de votre logement. Si
aucune des solutions ci-dessus ne foncti-
onne, contactez le service après-vente Braun.
Vérifiez la position correcte de l'accessoire.
Assurez-vous que le joint est correctement
monté.
Ferme le couvercle et le bouchon doseur
Suivez nos recommandations quant au rem-
plissage maximal (tableau I)
Nettoyez le pied en caoutchouc pour garantir
une bonne adhérence.
Éteignez le blender, retirez le pichet du base-
moteur et vérifiez si la lame est bloqué. Sui-
vez la vitesse ou mode recommandé dans le
tableau .
Éteignez le blender, débranchez-le et atten-
dez au moins 20 minutes avant de reprendre
le fonctionnement. Si le code d'erreur ne
disparaît pas, contactez le service après-
vente Braun.
Éteignez le blender et rallumez-le. Si le code
d'erreur ne disparaît pas, contactez le service
après-vente Braun.

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Triforce jb 9040Triforce jb 9041

Table of Contents