Pulsar CHROMA Series Manual

CHROMA
GENERAL INFORMATION
CZ6-100C ChromaZone6
CZ12-200 ChromaZone12 200W - Mk2
CZ12-200IP ChromaZone12 200W - IP65
CPSU2
ChromaPSU2
8075G ChromaFlex Grey 5 Core Multiway Cable
8075SUB ChromaFlex Submersible 5 Core Cable
Pulsar's Chroma Lighting Fixtures - ChromaStrips ,
T M
C h r o m a T u b e s
T M
ChromaScapes ,
TM
ChromaHearts , ChromaInGround , ChromaFlood50 ,
TM
ChromaPoint , ChromaInGroundMR16SS , etc
state of the art, high brightness, high efficiency Red, Green and
Blue LEDs. These three primary colours can be mixed together
to make an incredible pallet of 16.7 million colours.
Each ChromaFixture requires a +24VDC supply and three 0 to
+10V control signals to control the level of Red, Green and Blue.
These control signals and the low voltage power are provided by
the CZ12 and CZ6 controllers which can drive up to 12 or 6
ChromaFixtures respectively.
Please see the ChromaFixtures Leaflet
luminaires themselves and page 3 -
Loading Data which will inform you of how many fixtures you may
put on the outputs of different ChromaZones.
The ChromaZone
making it possible to achieve fantastic effects without
programming. These internal effects can be selected via the UIM
(User Interface Module)
mode or from a controller using a digital
signal.
When receiving a signal the
42 or 46 Channel Modes Please see the lid printing page for
details of these Operating Modes, how to select them, Channel
Listings, and further information.
Model Outputs
CZ6-100C
CZ12-200(IP)
CPSU2
Pulsar Light of Cambridge Limited
RANGE
TM
100W - Compact
TM
TM
TM
PSU
T M
, C h r o m a P a n e l s , C A R 1 1 1
T M
CBAT17 , ChromaBatten50 ,
TM
TM
TM
for details of the
ChromaZone Max Fixture
has numerous chases and effects built in
on the lid of the unit in Stand Alone
DMX D ( igital
CZ6/12 can operate in 3, 6, 9, 10, 36,
.
Max Load Control
6 100W DMX
200W
12 DMX
35W 0-10V
2
, 3 Coldhams Business Park, Cambridge, CB1 3LH, England
CHROMA
The CBAT50, CFLD50 and CIG50 require up to 50 Mains Watts
each which will reduce the number of products you can use per
ChromaZone e.g. 4 x CFLD50 = 200W. Do not exceed the max
mains wattage of the zone.
NB - Patents applied for. Trade Marks, Copyright, Registered
and Unregistered Design Rights apply on all Chroma
Products.
CHROMAZONE MAINS SUPPLY
Mains Supply
TM
mains voltage from 85-277 VAC, 50-60Hz, (self adjusting).
T M
T M
Power consumption: CZ6 - 100 Watts, CZ12 - 200 Watts
TM
depending on the number of fixtures connected and their output
levels. Please see the table shown below for more information.
., contain
A mains cable
supplied (not supplied with IP Zones). To unlock the IEC
connector, pull/side the red tab towards yourself then pull
connector out. The other end of the cable should be fitted with a
suitably approved and rated mains plug. Note: in some countries
it is a requirement that such a plug be fitted by a qualified
electrician.
,
WARNING - THIS APPLIANCE MUST BE EARTHED
For safety we recommend the use of a Residual Current
Circuit Breaker. An RCCB MUST be used when powering
M ultiple ) X
e.g. ChromaFixtures in wet environments.
Electronics On/Off Switch
Electronics Mains Fuse
50W 17W CP300 MR16
2 6 24
12 48
4
0 8
2
Tel: 44 (0)1223 403500
7571 PSU12-200IP Instructions
ZONE
- The ChromaZone(s) works correctly on any
with locking IEC female connector attached is
Cable Colours
Green/Yellow = Earth / Ground
Brown = Live / Phase / Hot
Blue = Neutral
with built in Indicator Neon
: 5 Amp, HRC, 5x20mm.
Link Point Strip 25/X1
30 48 48 7.2 mts
60 96 14.4 mts
96
10 16 2.4 mts
16
Email: sales@pulsarlight.com
.
Strip X3
2.4 mts
4.8 mts
0.6 mts
Web: www.pulsarlight.com