English - Crown CT44059 Original Instructions Manual

20 Vertical emitter window
21 Battery (AA-type) *
22 Carrying bag *
23 Horizontal emitter window
24 Laser beams on / off switch
25 Mounting screw *
26 Locking handle *
27 Carriage *
28 Magnet *
29 Tripod *
30 Charger indicator *
31 Socket for charger connection *
* Optional extra
Not all of the accessories illustrated or de-
scribed are included as standard delivery.
Installation / regulation
Do not draw up the fastening ele-
ments too tight to avoid damaging
the thread.
Mounting / dismantling / adjustment
of some elements is similar for all
appliance models. In this case no
particular appliance model is indi-
cated in the explanatory drawing.
Battery installation (see fig. 1-2)
• Install the batteries 21 (AA-type, 4 pcs�) in
the housing 14, as shown onto fig. 1. Caution:
during installation of batteries 21 in the hous-
ing 14, observe correct polarity (see fig. 1).
Open cover 8 (see fig. 2.1).
•
• Install housing 14 (with installed batteries 21)
or battery 13 into appliance (see fig. 2.2). Note:
the housing 14 and battery 13 are specially
shaped and can only be installed in one posi-
tion. Do not use excessive force when install-
ing the housing 14 or battery 13 to avoid dam-
aging them or appliance.
• Close cover 8 (see fig. 2.3).
• Disassemble in the reverse sequence�
Universal holder (see fig. 3-8)
Install the appliance on the universal holder 18
•
using the mounting screw 25 as shown in fig. 3-4.
You can move the appliance mounted on the
•
universal holder 18 up or down (see fig. 5).
• Rotate the locking handle 26 as shown
onto fig. 5.1 - this will allow to move the car-
riage 27 up or down�
• Move the carriage 27 up or down (see
fig. 5.2).
Rotate the locking handle 26 as shown
•
onto fig. 5.1 - this will lock the position of the
carriage 27�
• You can rotate the appliance mounted on the
universal holder 18 (see fig. 6).
Release
•
fig. 3.2, 4.2).
• Rotate the appliance (see fig. 6.1).
• Tighten mounting screw 25�
For CT44059, CT44060, CT44065 - you can
•
move horizontally the appliance mounted on the
universal holder 18�
• Release
fig. 3.2, 4.2).
• Move the appliance (see fig. 6.2).
Tighten mounting screw 25�
•
• You can install the universal holder 18 on fer-
romagnetic metal surfaces (elements of metal
structures, metal doors, frame structures for fix-
ing drywall, etc�) using the magnets 28� In this
case, the appliance shall be installed in the posi-
tion shown in figure 7. Note: if you flip the ap-
pliance, the self-leveling system of the laser
head will be misguided.
• You can suspend the universal holder 18 as
shown in figure 8.1.
You can install the universal holder 18 on a
•
tripod 29 with a mounting thread 1/4"-20 UNC
or 5/8"-11 UNC (see fig. 8.2). Attention: tri-
pod 29 is not included in delivery set.
• If you hear an sound signal when the ap-
pliance is turned on and the laser beams are
flashing, the deviation of the appliance from the
horizontal plane is more than ±3°� In this case,
try changing the position of the appliance or re-
install it�
Battery charging
[CT44060, CT44061, CT44065]
Initial operating
The appliance is delivered with partial bat-
tery 13 charge. Fully charge the battery 13
before the first use of the appliance.
If the power indicator 7 flashes
when the appliance is switched on,
it means that the battery 13 is dis-
charged and needs to be charged.

English

18
mounting screw
mounting screw
25 (see
25 (see