AN-102C Photoelectric Smoke Detector User Manual 1. Introduction AN-102C is a domestic photoelectric smoke detector with LoRaWAN compliance. It can detect smoke generated by fire and send alarm signal in time. The alarm adopts photoelectric smoke sensing device and excellent production technology, with stable work performance and beautiful appearance.
Page 4
AN-102C Photoelectric Smoke Detector User Manual Technical parameter Description Parameter Model AN-102C Product Name Photoelectric Smoke Detector Working Voltage DC3V(CR123A lithium battery) Alarm Indicator Alarm Sound >80dB/3m pressure Working -10℃~+50℃ Temperature Working Humidity ≤95%RH(non-condensing) Communication LoRaWAN protocol Frequency CN470-510/US902-928/AS923/EU863-870/AU915-928 Dimension...
AN-102C Photoelectric Smoke Detector User Manual 3. How to work Smoke detection system The whole smoke detection system consists of AN-102C photoelectric smoke detector, LoRa gateway, cloud platform and application management platform. Users can also use their own platforms which must be LoRaWAN compliant.
Page 7
AN-102C Photoelectric Smoke Detector User Manual red indicator will flash every 53 seconds, and the buzzer will beep shortly. Test: Press the self-check button and hold it for more than 1 second. The red LED indicator will flash quickly and the buzzer will beep, which indicate the device is working normal.
Page 8
AN-102C Photoelectric Smoke Detector User Manual Battery replacement Remove the device from the mounting base first. Remove the inside module from the device, take out the battery, press and hold test/hush button for 5 seconds and then release, so that the device can discharge remaining power, or it may send a low battery power fault warning.
AN-102C Photoelectric Smoke Detector User Manual 4. Configuration 4.1 Precaution For device normal operation and detection accuracy, please pay attention to the following matters before configuration: Before configuration, please contact our technical staff for the relevant software and manual.
AN-102C Photoelectric Smoke Detector User Manual a) Install the CP210x driver for wireless configuration tool, file as below: b) Install Winext manage App, file as below: 4.3.2 Install CP210x driver for wireless configuration tool (1) Open CP210x driver for wireless configuration tool (2) Select the driver program to install depending to the system type.
Page 11
AN-102C Photoelectric Smoke Detector User Manual Select Accept the License Agreement and click on Next, as below:...
Page 12
AN-102C Photoelectric Smoke Detector User Manual Wait for a while and click on Finish, as below: Check the driver program after installation finished. Click on Computer-Attribute- Device manager, as below:...
AN-102C Photoelectric Smoke Detector User Manual 4.3.3 Parameter setting (1) Insert the wireless configuration tool into the laptop USB port. Start host configuration near the device installation location. (2) Insert the wireless configuration tool to the USB port. Click on...
Page 14
AN-102C Photoelectric Smoke Detector User Manual (3) Open and run Winext Manage App to configure the basic parameters, please refer to the image below: a. Select port number, click on Open SerialPort. b. Reboot device and its DevEUI will be shown in the pull-down menu.
AN-102C Photoelectric Smoke Detector User Manual 5. Installation 5.1 Package contents Accessory Qty(pc) AN-102C Photoelectric Smoke Detector Self-tapping Screw Expanding Plug 5.2 Quick guide 1. Choose a proper position for installation and make marks. Install the base to the ceiling with screws and expanding plugs. Remove the bolts from the base.
Page 16
AN-102C Photoelectric Smoke Detector User Manual Ceiling-mounted Installation Figure: Ceiling-mounted installation Notes: It’s recommended to be installed in the center of the ceiling for better signal coverage. For installation, please avoid the places blow as possible: Places where dust, powder and water vapor is largely retained, where corrosive gases may be generated, the temperature or the humidity is too high.
AN-102C Photoelectric Smoke Detector User Manual 6. Communication Format Using Fport 46, data is reported in hexadecimal. 6.1 Data report 6.1.1 Heartbeat data frame (0x01) This data consists of 11 bytes, here are definitions as below: Sensor Type 1 byte...
AN-102C Photoelectric Smoke Detector User Manual no failure bits that used complemented by 0. Optical Maze 1 byte Range: 1~100, measured in percentage Pollution Rating Wireless Module 1 byte Actual value should be divided by 10 Voltage 6.1.2 Self-test (0x02)
Page 19
AN-102C Photoelectric Smoke Detector User Manual bit2: low battery voltage alarm status of device. bit2=1, there is a low battery voltage alarm, bit2=0, there is no low battery voltage alarm Failure state 1 byte bit0: failure state of device. bit0=1, there is a failure, bit0=0 there is no failure.
AN-102C Photoelectric Smoke Detector User Manual 7. Trouble-shooting Description Analysis Trouble-shooting False alarm There is a large amount of 1. When smoke and vapor smoke or vapor indoors gone, reboot but no fire. device. 2. Install the device to other...
Page 21
AN-102C Photoelectric Smoke Detector User Manual Shenzhen Winext Technology Co., Ltd. Web: www.winext.cn http://winext.en.alibaba.com Address: 5 Floor, Building B50, Zhongchuang Industrial Park, Liuxian Rd, Taoyuan Street, Nanshan District, Shenzhen 518055, China Tel:(+86) 0755-23990916 Fax:(+86) 0755-23990906 Email: jessie@winext.cn ---------------------------------------------------------------------------------------------------------------------- This is a product manual as an installation, operation and use file. Specifications subject to change are without...
Need help?
Do you have a question about the AN-102C and is the answer not in the manual?
Questions and answers