1. Manuals
  2. Brands
  3. SPYKER Manuals
  4. Paint Sprayer
  5. SPYDSS-9G
  6. Operator's manual

SPYKER SPYDSS-9G Operator's Manual

Single nozzle drop-in sprayer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATOR'S MANUAL
Single Nozzle SPYDSS-9G Drop-In Sprayer
Spyker Spreaders
Contact us at 800.972.6130
www.spyker.com
IMPORTANT
!
!
This manual contains information for the safety of persons and property.
Read it carefully before assembly and operation of the equipment!
©2021 Spyker Spreaders/A Brinly-Hardy Co.
Page 1
1019621-A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SPYDSS-9G and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for SPYKER SPYDSS-9G

Summary of Contents for SPYKER SPYDSS-9G

  • Page 1 OPERATOR'S MANUAL Single Nozzle SPYDSS-9G Drop-In Sprayer Spyker Spreaders Contact us at 800.972.6130 www.spyker.com IMPORTANT This manual contains information for the safety of persons and property. Read it carefully before assembly and operation of the equipment! ©2021 Spyker Spreaders/A Brinly-Hardy Co.

  • Page 2: Table Of Contents

    SPYKER • S60-12020 • S100-12011 SET-UP PROCEDURE The SPYDSS-9G was pressure tested prior to shipment. Some components were disassembled for packaging and shipment. The basic set-up procedure is as follows: • Remove all contents from inside the tank. • Remove all contents from the box.

  • Page 3: Parts

    Parts DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 BATTERY AND SPRAY WAND SPRAYER HANDLE MOUNTING HARDWARE WAND PARTS Part # Description 1019634 Angle Bracket 1019635 Wing Nut 1019636 Mounting Clip 1019637 Screw #6 x 1/2" 1019638 Pan Head Screw 1019639...
  • Page 4 Part Explosions DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 ELECTRICAL COMPONENTS Part # Description 1019642 Toggle Switch 1019643 Switch Bracket 1019644 Pump / Switch Wiring Assembly 1019645 Screw Clamp 1019646 Battery 1019647 Battery *High Capacity 1019648 Battery Wiring Assembly 1019649*...

  • Page 5: Assembly

    Part Explosions DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 NOZZLE ASSEMBLY Part # Description 1019652 Hose Barb, 1/4 NPT x 3/8 Male 1019653 Single Swivel Adapter 1019654 Strainer w/ Check Valve 1019655 1019656 Wide Angle Spray Tip 1019657 Clearbraid Hose 3/8"...
  • Page 6 Part Explosions DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 TANK & PLUMBING Part # Description 1019662 Poly Tank, 9 Gallon 1019663 Regulator 1019664 0-60 SS Liquid Filled Gauge 1019665 1/2" Close Nipple Hex 1/2"...
  • Page 7 Part Explosions DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 TANK & PLUMBING Part # Description 1019669 Clear Braid Hose; 1/2" ID x 3.5" 1019670 Easy Seal Clamp; for 1/2" ID Hose 1019671 1/2" FPT x 1/2" Barb Straight Swivel 1019672 1/2"...
  • Page 8 Assembly Clean all debris from the spreader hopper. Attach the spray hose wingnut (30) to the ball valve (47). Place the empty tank assembly (31) in the spreader hopper. NOTE: Face the battery mounted toward the rear. Fig. 3 Snap the hose (26) into the clips (28) with the nozzle facing forward.
  • Page 9 Assembly Align the thumb switch (15) with the handle (B) and 8. Connect swivel elbow fitting (41) to the pump inlet attach with a screw clamp (17). port (40). Fig. 8 Fig. 5 Install the pump wiring assembly clips (16) to the thumb switch spades (15). Install the pressure gauge (41).

  • Page 10: Use And Care

    BATTERY RECHARGING 8. Turn on the switch and observe the spray pattern from the spray nozzle. Check the hose assembly The SPYDSS-9G’s battery is a sealed, for leaks. maintenance-free 12-volt battery. 9. Once the unit has been pressure tested and you are familiar with its operation, you can begin the Charging at a low rate (3 amp max.) with an automotive...

  • Page 11: Calibration

    READ BEFORE USING CALIBRATION The SPYDSS-9G is equipped with a Hypro DeflecTip wide-angle flat flood nozzle. The table below will serve as a ref- erence for application rates. A working pressure of 15-20 psi will provide adequate coverage. The nozzle should be adjusted to provide a 60-65 inch spray width with a 4-6 inch overlap of the previous spray pass.

  • Page 12: Troubleshooting

    Troubleshooting READ BEFORE USING Problem Possible Cause Solution Pump runs, Battery drained Recharge battery but little Tank empty Refill tank or no flow Filter clogged Clean filter screen Filter bowl not on tight Tighten filter Filter gasket faulty or missing Check / Replace gasket Broken fitting or hose Repair as necessary Pump needs repair...

  • Page 13: Accessories

    Accessories SPREADER-MATE TRUCK CHARGER KSP18-TCG The charger allows the sprayer battery to be recharged from a truck charging system in between jobs. Included is 20 feet of 10-gauge x 2 wire, 40 amp circuit breaker, battery wire connectors, and a quick-connect KSP18-TCG modular plug for the battery.

  • Page 14: Warranty

    The battery and the pump elastomers, which are considered normal wear items, carry a 90-day warranty against defects in materials and workmanship. Spyker Spreaders will not be liable for any loss, damage or expense including, but not lim- ited to, consequential or incidental damages, arising from the operation, condition or use of the item.

Table of Contents