Table of Contents
Advertisement
Quick Links
OPERATOR'S MANUAL
SPYDSB-9G Drop-In Sprayer with 62" Boom
Spyker Spreaders
Contact us at 800.972.6130
www.spyker.com
IMPORTANT
!
!
This manual contains information for the safety of persons and property.
Read it carefully before assembly and operation of the equipment!
©2021 Spyker Spreaders/A Brinly-Hardy Co.
Page 1
1019622-C
Advertisement
Table of Contents
Related Manuals for SPYKER SPYDSB-9G
Summary of Contents for SPYKER SPYDSB-9G
- Page 1 OPERATOR'S MANUAL SPYDSB-9G Drop-In Sprayer with 62” Boom Spyker Spreaders Contact us at 800.972.6130 www.spyker.com IMPORTANT This manual contains information for the safety of persons and property. Read it carefully before assembly and operation of the equipment! ©2021 Spyker Spreaders/A Brinly-Hardy Co.
-
Page 2: Table Of Contents
• HPS Chariot SPYKER • S100-12011 SET-UP PROCEDURE The SPYDSB-9G was pressure tested prior to shipment. Some components were disassembled for packaging and shipment. The basic set-up procedure is as follows: • Remove the spray wand from inside the tank. -
Page 3: Parts
Parts DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 BATTERY AND SPRAY WAND SPRAYER HANDLE MOUNTING HARDWARE WAND PARTS Part # Description 1019634 Angle Bracket 1019635 Wing Nut 1019636 Mounting Clip 1019637 Screw #6 x 1/2" 1019638 Pan Head Screw 1019639... - Page 4 Part Explosions DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 ELECTRICAL COMPONENTS Part # Description 1019642 Toggle Switch 1019643 Switch Bracket 1019644 Pump / Switch Wiring Assembly 1019645 Screw Clamp 1019646 Battery 1019647 Battery *High Capacity 1019648 Battery Wiring Assembly 1019649*...
- Page 5 Part Explosions DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 BOOM COMPONENTS DIAGRAM Part # Description 1019697 Right Boom Section 1019698 Hose, 3/8" ID x 24" 1019699 Spring, Stainless Steel 1019700 Center Boom Section 1019701 Hose, 3/8"...
- Page 6 Part Explosions DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 TANK & PLUMBING Part # Description 1019662 Poly Tank, 9 Gallon 1019663 Regulator 1019664 0-60 SS Liquid Filled Gauge 1019665 1/2" Close Nipple Hex 1/2"...
- Page 7 Part Explosions DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 TANK & PLUMBING Part # Description 1019669 Clear Braid Hose 1/2" ID x 3.5" 1019670 Easy Seal Clamp For 1/2" ID Hose 1019671 1/2" FPT x 1/2" Barb Straight Swivel 1019672 1/2"...
-
Page 8: Assembly
Part Explosions DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 NOZZLE ASSEMBLY Part # Description 1019706 Dripless Nozzle Body, Double w/ Cap 1019707 Dripless Nozzle Body, Single w/ Cap 1019708 Turbo TeeJet Air Induction Nozzle 1019709 Quickjet Cap 1019710... - Page 9 Assembly Utilizing the holes illustrated here, align the With the boom arms folded closed, install the boom arms to the center section. Attach using springs (23) on the spring mounting tabs. the 3/8” hinge bolts and locknuts (28). NOTE: Do not tighten fully! Allow movement. Fig.
- Page 10 Assembly Using the boom support brackets (A) as a Clean all debris from the spreader hopper. template: Drill through the mounting openings, Place the empty tank assembly (32) in creating two 1/4 inch diameter holes in the your spreader hopper with the battery mounted hopper.
- Page 11 Assembly 10. Connect swivel elbow fitting (42) to the pump inlet Install the sprayer nozzles (54), screens (56), port (41). washers (57) and caps (55). Fig. 10 Fig. 7 Install the handle thumb switch (15) with a screw clamp (17). Plug in the switch wiring (16). Fig.
-
Page 12: Use And Care
Use and Care READ BEFORE USING GENERAL OPERATION & INITIAL START-UP MAINTENANCE & PRESSURE TESTING The sprayer pump is turned on and off by the thumb 1. Turn the pressure regulator knob counter- switch mounted on the handlebar of the spreader. Each clockwise all the way. -
Page 13: Battery Recharging
READ BEFORE USING BATTERY SPRAY NOZZLE RECHARGING SETTINGS The SPYDSB-9G’s battery is a sealed, The SPYDSB-9G is equipped with dripless maintenance-free 12-volt battery. nozzle bodies and special shut-off caps. Charging at a low rate (3 amp max.) with an automotive Each nozzle body requires 5 psi of system pressure to quality battery charger will extend battery life. -
Page 14: Calibration
READ BEFORE USING CALIBRATION The SPYDSB-9G is equipped with a Hypro DeflecTip wide-angle flat flood nozzle. The table below will serve as a ref- erence for application rates. A working pressure of 15-20 psi will provide adequate coverage. The nozzle should be adjusted to provide a 60-65 inch spray width with a 4-6 inch overlap of the previous spray pass. -
Page 15: Troubleshooting
Troubleshooting READ BEFORE USING Problem Possible Cause Solution Pump runs, Battery drained Recharge battery but little Tank empty Refill tank or no flow Filter clogged Clean filter screen Filter bowl not on tight Tighten filter Filter gasket faulty or missing Check / Replace gasket Broken fitting or hose Repair as necessary Pump needs repair... -
Page 16: Accessories
Accessories SPREADER-MATE TRUCK CHARGER KSP18-TCG The charger allows the sprayer battery to be recharged from a truck charging system in between jobs. Included is 20 feet of 10-gauge x 2 wire, 40 amp circuit breaker, battery wire connectors, and a quick-connect KSP18-TCG modular plug for the battery. - Page 17 Please find your product serial number and model number, then contact our Customer Service department: In North America and Canada call Toll-Free: 800-972-6130 Chat online: www.spyker.com NOTES English Manual Page 17 1019622-C...
-
Page 18: Warranty
The battery and the pump elastomers, which are considered normal wear items, carry a 90-day warranty against defects in materials and workmanship. Spyker Spreaders will not be liable for any loss, damage or expense including, but not lim- ited to, consequential or incidental damages, arising from the operation, condition or use of the item.
Need help?
Do you have a question about the SPYDSB-9G and is the answer not in the manual?
Questions and answers