Page 4
Un-Assemble Swivel Bracket ............48 Disassemble Swivel ..........................48 Appendix: F Configure IP Router (1 Example) ..........52 Setting Up the Router for Port Forwarding ................52 Reserve the IP or Bind the IP to a MAC ..................56 Paradox Insight ™ HD77 Installation Guide...
In case of a security breach, the HD77 camera provides HD videos with high-quality audio of events for visual verification and reporting. When an alarm is triggered, the HD77 sends a pre-recorded video (360p) in color or black and white (night vision) and 10 images (jpegs) to allow users and the CMS to view what triggered the alarm.
Up to 4 HD77 cameras can each be assigned up to 4 different zones. Configuring HD77 cameras for ROT is done by the master user through the Paradox Insight™ App. 1.2 Overview The Paradox Insight™ HD77 camera is a highly reliable HD video (720p in color) and high-quality audio PIR camera. Camera...
Page 10
LED3 — PIR indication can be set to On or Off by the installer, however, the VOD indication can be turned Note: off only by the master user using the Paradox Insight™ application. Turning the VOD LED off may be considered in some countries as a violation of applicable laws. Make Note: sure to install the HD77 according to local laws.
If the installer is connecting wirelessly one less port is needed. Note: A single CAT5 or higher cable can be used to wire a single HD77 camera. This cable includes 2 twisted Note: pairs for the 4-wire combus and 2 twisted pairs for the Ethernet lines. When using this option the cable length is limited to 50 meters.
Cabling Option #1 A single CAT5 or higher cable can be used to wire a single HD77 camera. This cable includes 2 twisted pairs for the 4-wire combus and 2 twisted pairs for the Ethernet lines. When using this option the cable length is limited to 50 meters.
• For LAN connection, use a CAT5/CAT5e/CAT6 Ethernet cable (70m max. for option #2, 50m max. for option #1 ) between the HD77 and the router. When using a single CAT5 cable (option#1) to also connect the 4-wire combus, the wire run is limited to Note: 50 meters.
Figure 9 – Separating the Module from the HD77 Housing Separate the front cover with module from the back plate of the HD77. Do this by carefully pulling out the bottom of the front cover and sliding the front cover up. The two parts will separate.
Snap the bracket assembly to the wall plate by placing it on top of the wall plate and sliding it down until it locks. Figure 12 – Connect the Bracket Assembly to the Wall Drill the knockouts for wall installation on the HD77 back plate. Tighten this screw to lock...
BabyWare and add the location and label to each module. Screw the HD77 back plate to the swivel bracket using the 4 self tapping screws. Adjust the bracket position as desired and tighten the screw to lock it in place (through the opening in the back plate).
Step 3. Close the lock mechanism at the bottom of the HD77 camera. By securing the lock, the installer diagnostic LEDs will be turned off. Note: Connect the Ethernet line to the router (if not already connected). Make sure the router is turned on.
16V AC transformer to an outlet. The system will boot-up including the cameras. The HD77 boot-up is indicated by LED3. The LED flashes blue for up to 3 minutes. Use VOD to verify camera vision / image / angle. In BabyWare => HD77 Properties => Video tab => play button...
Figure 18 – HD77 Video Stream in BabyWare When installed with a swivel bracket, you can adjust the HD77 position by doing the following. Step 1. Remove the camera. Step 2. Loosen the screw. See Figure 14. Step 3. Make your adjustments.
Click the link below and sign in to the site using your Paradox.com login user name and password to see Note: a video about creating a new account. http://www.paradox-insight.com/learning/configuration-createanewaccount Figure 19 – BabyWare Account Window Open the window. The following window opens up. Connection Options Settings Paradox Insight ™ HD77 Installation Guide...
Figure 20 – IP150 Settings Window Click the button. A list of all IP150 devices appears. Locate Figure 21 – Locate IP Device on Network Select your IP150 device and Click . The IP device configuration window opens. Configure Paradox Insight™ HD77 Installation Guide...
Figure 22 – IP Device Configuration Enter the IP 150 module password. Click OK to confirm password. Click OK to finish configuring the IP 150 device. Click Connect to finalize the connection settings. Paradox Insight ™ HD77 Installation Guide...
Chapter 4 Programming Server parameters must be programmed through BabyWare only. PIR parameters of the HD77 can be configured by the installer using the TM50 touchpad, the K641 series keypads and the K656 keypad, and by using BabyWare software. Due to our constant efforts to improve our products the software screen grabs may not be exactly the Note: same as your screen.
Enter the (CMS) parameters. Central Monitoring Station 4.4.1 Receiver Parameters (Monitoring Station Reporting) To configure your HD77 to report events to an IPRS7 software, check the checkbox. Reporting Enabled Enter the parameters. These parameters come from the Central Monitoring Station.
If your ISP assigns a dynamic WAN IP (as in most cases) you must check the Poll PMH(ParadoxMyHome) checkbox and make sure the Paradox Insight™ App is configured for a Dynamic IP WAN address. See the Paradox Insight™ App User Manual.
If you do not wish to use the PMH, you must get a static WAN IP from your ISP and uncheck the Poll PMH (ParadoxMyHome). Later, you will have to manually key-in this IP address into the Paradox Insight™ Application and the BabyWare application HD77 programming page.
DHCP range. • Record one of the addresses outside the DHCP range as the one you will use for the HD77. • The range shown in following figure, would leave addresses two to four and 101 to 254 available (all the numbers in an IP address are between 1 and 254.).
Step 1. Add a service/item, set the Port to >50000, for example 50001, and enter the IP address selected in the previous step 7 or the HD77 module. Step 2. If port 50001 is already used, you can use another one, such as 50002 or 50003.
Chapter 5 PIR Parameters Programming PIR parameters of the HD77 can be configured by the installer using the TM50 touchpad, the K641 series keypads and the K656 keypad, and by using BabyWare software. To program the module sections from a Paradox keypad BabyWare must be disconnected from the Note: system.
WIFI router will not test this, please use the 3G network. 5.1 Programming Through the TM50 Touchpad To program the HD77 from any installed keypad, BabyWare must be disconnected from the system. Note: Only PIR parameters for the HD77 can be configured through the touchpad.
Key in Section [ 4003 Figure 38 – Installer Programming Screen Enter the module’s [ ]. Click Serial Number Next Figure 39 – Module Serial Number Screen Enter Section [ Figure 40 – Programming Section Paradox Insight ™ HD77 Installation Guide...
Select PIR security level, level 0 to level 2; Default is #0. 5.2 Programming Through the K641 series Keypads and K656 Keypad To program the HD77 from any installed keypad, BabyWare must be disconnected from the system. Note: Only PIR parameters for the HD77 can be configured through the keypad.
Page 34
K641series keypads High (Sensitivity level) 3 Security Level [003] (Mild environment) (003) 000-000 Normal Default as seen on the TM50 Medium (000) High (Harsh as seen on the environment) K641series keypads Paradox Insight ™ HD77 Installation Guide...
ParadoxMyHome is a Paradox Domain Name System (DNS) service that enables the installer to remotely access a Paradox Reporting Device (e.g. IP150 or HD77). A dynamic IP address is assigned automatically, and can change on a regular basis. ParadoxMyHome keeps track of these changes and associates the current IP address to the Site ID (e.g.
To unregister follow the same procedure but select at the drop down menu. Note: Unregister from PMH Enter the requested information. The SiteID should be unique for the site (up to 4 HD77 cameras). Installer e-mail address and password from his ParadoxMyHome site This Site ID is to be given to the end user.
To delete a site from PMH, first delete the site from the Registered Devices page and then delete it from Note: the Deleted Devices page. You must delete your site from BOTH pages. Figure 47 – ParadoxMyHome Site Paradox Insight™ HD77 Installation Guide...
This MUST be checked with an external network in order to verify that port forwarding is working – using wireless network from the property’s WIFI router will not test this, please use the 3G network. Paradox Insight ™ HD77 Installation Guide...
Chapter 8 Upgrading Firmware Use Babyware to upgrade firmware on all of HD77 cameras on your site. To update firmware on the HD77 you will need BabyWare V2.8 or higher. Double click on any connected HD77 camera listed in BabyWare.
If BabyWare does not automatically find the IP address and port numbers for your cameras perform the following procedure. For DHCP Go to HD77 — Settings. See (see Figure 54). Figure 52 – HD77 — Settings Update Graphic On the HD77 Settings window select Auto Detect Paradox Insight ™...
Figure 53 – HD77 Settings Window Click Refresh Click The installer should not leave the house without verifying the VOD can be seen through the App! Note: This MUST be checked with an external network in order to verify that port forwarding is working – using wireless network from the property’s WIFI router will not test this, please use the 3G network.
For Static IP Go to HD77 — Communication — Settings. See (see Figure 54). Figure 54 – HD77 — Settings Update Graphic On the HD77 Settings window select IP/Static Figure 55 – HD77 Settings Window Update Graphic Paradox Insight ™ HD77 Installation Guide...
Step 1. Type the Default Gateway IP address from the command prompt window into your browser. Step 2. You will be asked for a user name and password. Get these from your ISP. Step 3. Bind (Reserve) the Mac address to its IP address for each HD77. Paradox Insight™ HD77 Installation Guide...
Page 44
HD77 Programming page => Communication => Register to PMH. Your HD77 camera server settings should now be configured for a static IP for the LAN. The installer should not leave the house without verifying the VOD can be seen through the App! Note: This MUST be checked with an external network in order to verify that port forwarding is working –...
(H x W x D)15 cm x 7.5 cm x 5 cm (6 in x 3 in x 2 in) See the Paradox.com website for the latest certifications for this product. Environmental http://www.paradox.com/terms/ Operating Temperature -10° C to +40° C (14° F to 104° F) Paradox Insight™ HD77 Installation Guide...
The beam pattern for the detector is shown below. Top view Side view (5.6) (13) (26) (40) Feet (13) 2.1m (6'8") (6'6") Meters Figure 58 – PIR Detector Beam Pattern EN 50131 testing has been performed for 110 degrees. Note: Paradox Insight ™ HD77 Installation Guide...
(2) increase the separation between the equipment and receiver; (3) connect the equipment to an outlet on a circuit other than the one to which the receiver is connected, or (4) consult the dealer or an experienced radio/tv technician for assistance. Paradox Insight™ HD77 Installation Guide...
Flat washer Lock washer Pan head screw #6-32 Back housing with nut installed HD77 camera housing mount Figure 59 – HD77 Swivel Bracket Parts Disassemble Swivel Remove the pan head screw. Remove this screw Figure 60 – Assembled Swivel Bracket Do not drop the flat washer or the lock washer.
Figure 61 – Screw the Slider, HD77 Camera Housing and Back Housing Together Unlock the cover of the camera. Separate the front cover from the backplate of the HD77 by carefully pulling out and sliding up. Assemble the swivel mount.
HD77 camera housing mount (part #7) back housing (part #6) Slider pan head screw washers (part #8) Figure 64 – Screw the Slider, HD77 Camera Housing and Back Housing Together Make sure to screw the anti-tamper from the camera back plate to the swivel bracket.
Page 51
If you are using BabyWare the serial number will be displayed, but you will need to write down the correct location for each module according to the serial number. Step 8. Screw the HD77 back plate to the housing mount using the 4 self tapping screws. Figure 66 – Wire the Camera Step 9.
Command. Step b. Select Command Prompt. Step c. At the prompt Type ipconfig Step d. Press Enter. The router IP address will be the Default Gateway ..:xx.xx.xx.xxx Paradox Insight ™ HD77 Installation Guide...
In the router’s configuration page, check the DHCP settings: Step 1. If DHCP is not enabled, verify that the IP address range is large enough to accommodate all of your cameras. Four cameras will require 4 IP addresses. Paradox Insight™ HD77 Installation Guide...
Step 1. In the router’s configuration page, go to the Port Forwarding section (also known as “port map- ping”, "NAT", (network address translation), or “port redirection”). Step 2. Select an available port on the router and assign it to the HD77 camera. Select a port above #50000 for the port.
Page 55
10.0.0.132 50042 facing sliding rear door 10.0.0.133 50053 Safe room facing the safe 10.0.0.134 50063 2nd floor looking down the staircase 10.0.0.135 50073 Each camera needs a separate IP address and matching external port. Note: Paradox Insight™ HD77 Installation Guide...
Right click the HD77 camera. Go to Communications => Settings Figure 72 – HD77 Settings Select IP Static. Use the IP address and port number you selected in the router binding and port forwarding. Paradox Insight ™ HD77 Installation Guide...
Click Figure 73 – Locate Static IP Addresses Select the IP address with port for your static IP. Click Configure Click Repeat the process for each HD77 camera. Paradox Insight™ HD77 Installation Guide...
Page 58
For support, please contact your local distributor, or dial 1-800-791-1919 (in North America) or +1-450-491-7444 (outside North America), Monday to Friday, from 8:00 a.m. to 8:00 p.m. EST. You may also e-mail us at support@paradox.com. Additional information can be found at PARADOX.COM paradox.com Printed in Canada November, 2014 HD77-EI01...