Download
Share
Print this page
STALEX VS-400 Operating Manual
  1. Manuals
  2. Brands
  3. STALEX Manuals
  4. Saw
  5. VS-400
  6. Operating manual

STALEX VS-400 Operating Manual

Vertical band saw
Hide thumbs

Advertisement

Quick Links

Download this manual
VERTICAL BAND SAW
MODEL: VS-400
VS-500
VS-585
Operating Manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the VS-400 and is the answer not in the manual?

Questions and answers

Related Manuals for STALEX VS-400

Summary of Contents for STALEX VS-400

  • Page 1 VERTICAL BAND SAW MODEL: VS-400 VS-500 VS-585 Operating Manual...

  • Page 2: Table Of Contents

    Table of contents I.INTRODUCTION……………………………………………………………….3 II.INFORMATION ABOUT MAINTENANCE ASSISTANCE…………………3 ……………………………………………………4 III. SPECIFICATION ……… 4 IV.DESCRIPTION OF THE MACHINE AND ITS COMPONENTS ………………………………………..5-10 V. INSTRUCTION MANUAL …………………………………………..11 VI.INVERTER PARAMETER VII. DRAWING AND PARTS LIST…………………………………………12-21 VIII.ELECTRICAL DRAWING FOR VS-400,VS-500 and VS-585…… .22-24...

  • Page 3: I.introduction

    I.INTRODUCTION The “Operating instructions” are an integral part of the machine and should be consulted before, during and after the start up of the machine and whenever else required. The content of these instructions should always be carefully observed. The observance of the above is the only way to achieve the two fundamental aims of this manual: ●...

  • Page 4: Specification

    III. SPECIFICATION Item No. 388201 388202 388203 Model VS-400 VS-500 VS-585 310mm(12.2”) Max. Cutting capacity Height 285mm(11.2”) 336mm(13.2”) 400mm (15.7”) 500mm(19.7”) 585mm(23”) Width Table Size 550x600mm 660x700mm 660x700mm (21.7”x23.6”) (26”x27.6”) (26”x27.6”) Blade Speed(50Hz) 0～1400rpm 0～1400rpm 0～1400rpm Length of saw blade...

  • Page 5: Instruction Manual

    V. INSTRUCTION MANUAL PS. Please turn the Regulator to “the lowest speed” position before turning on the machine. 1. The mechanical construction of this machine is illustrated as shown on the Parts List. 2. The adjusting screws, above and under the Band Guides, can be adjusted as long as. 3.
  • Page 6 B. Sawing Material Selection: Before sawing, the operator must fully understand the quality of the sawing material. Example: With super high stencil steel, the machine should be run at a slower speed. Otherwise, the blade will overheat, be worn or broken easily. With thin material, it is recommended to use a wider blade pitch at high speeds;...
  • Page 7 Button during the welding until the blade back to black color. 3. Tempering operation a. Press the tempering button until the welding points begin to appear red color. Then, after the blade back to the normal color, do the previous action again. Repeat this pressing 5-7 times.
  • Page 8 Maintenance and trouble shooting 1. Maintenances a. put the voltage adj. knob back to mark of “i” when the machine is not working b. after half hour working, the machine can only be continue to work when the temperature is lowing down to the ambient temperature 2.
  • Page 9 Trouble Possible Reason Solution Blade do not a. Blade two ends is not a. Cut the two ends straight and flat. melt straight and flat b. Repair the electrode. b. Electrode is broken or worn. c. Polish the touch points of the switch c.
  • Page 10 Pressure: 0.20Kg/cm2 Type of fluid: Air L. Angles Cutting: 1. Declination sawing: Loose table nuts; adjust the table into the desirable position, and retighten the nuts. “R” shape sawing: Turn slowly because the sawing edge must remain flat, straight and smooth. 3.

  • Page 11: Vi.inverter Parameter

    VI.INVERTER PARAMETER: 1．Consumers are not allowed to adjust the parameters without authorization .(In case that machine failure is caused by any consumer who alters any parameter without authorization, the consumer should be responsible for the failure.) 2.Inverter parameters are only provided for the qualified technician. MAINTENANCE AND CAUTIONS Remarks: 1.

  • Page 12: Drawing And Parts List

    VII. DRAWING AND PARTS LIST VS-400 packing list and drawing Item Description Item Description Low door Wood brush Bolt M6X12 Bolt M5X20 Nut M6 Big washer 5 Block Bolt M5X16 Blade block material seat Washer 5 Blade stay bar Left seat board...
  • Page 13 Item Description Item Description Bolt M6X12 Flange Handle wheel Bearing 6206-2Z Bolt M6X6 Block 62 Elasticity pin 2X14 Handle Gear seat Bearing 51201 Bolt M6X25 Bolt washer Big washer 6 Elasticity pin 3X24 Worm Lead Screw Washer Bolt M8X25 Bolt washer Washer 8 Slanting gear Shaft seat...
  • Page 17 VS-500 and VS-585 packing list and drawing Item Description Item Description Low door Water box Bolt M6X12 Wood brush Nut M6 Bolt M5X20 Big washer 5 Bolt M5X16 Block Washer 5 Blade block material seat Left seat board 43.1 Spring pin 3X18 Right seat board Blade stay bar Bolt M6X8...
  • Page 18 Item Description Item Description Gate Motor Bolt M8X16 Belt A-1750 Rack Big saw wheel Blade protect cover 113.1 Bracket Washer 6 Bolt M8X25 Bolt M6X12 Flat key 12X50 Handle wheel Checking ring 40 Bolt M6X6 Low wheel shaft Elasticity pin 3X14 Bolt M12X55 Gear seat Leveling bolt...
  • Page 19 24(4) 25(4) 27(6) 18(4) 28(6) 16(2) 15(6) 32(2) 34(12) 35(12) 11(4) 9(2) 6(4) 5(4) 3(2) 36(2) 37(2) 4(4) 2(2)
  • Page 20 94(2) 85 86 87 83(2) 82(2) 73(2) 80(2) 77(4) 76(4) 71(4) 70(4) 68.1 64(2) 63(2) 58(4) 45(2) 44(2) 46(2) 43(2) 42(4) 41(4) 40(4) 54(4) 53(4) 52(8) 43.1(2) 52.1(4)
  • Page 21 137(2) 138(8) 135(2) 134(2) 141(2) 131(2) 130(2) 128(2) 127(2) 126(2) 113.1 118(4) 119(4) 121(2) 122(2) 115(2) 114(4) 112(2) 102(2) 110(2) 105(4) 106(4) 108(2) 109(2)

  • Page 22: Viii.electrical Drawing For Vs-400,Vs-500 And Vs-585

    VIII．ELECTRICAL DRAWING FOR VS-400,VS-500 and VS-585...
  • Page 25 Note: This manual is only for your reference. Owing to continuous improvement of the machines, Changes may be made at any time without obligation on notice.

This manual is also suitable for:

Vs-500Vs-585388201388202388203